Renaming Keys - Harman Kardon AVR 635 Owner's Manual

CONFIGURING THE REMOTE
T V < - V C R [ T R S ]
S A V E D
Figure 72
7. Once the punch-through is programmed, the
transport buttons of the second device named
will be used when those buttons are pressed
while the master device is in use.
Returning the Transport Control Settings to
Default Operation
If you wish to remove the Transport Punch-Through so
that the transport commands are returned to the fac-
tory default setting, follow the steps shown above,
except that in Steps 4 and 5, select the same device
for both the DEVICE IN USE on the left side of the
bottom line and the PUNCH-THROUGH device. In
the example used, the display to return the remote to
default settings will appear as shown in Figure 73.
P U N C H - T H R O U G H
T V < - T V
Figure 73
Renaming
While the names given to the buttons and inputs on
the remote represent recognizable categories of
audio/video products, system operation may be easier
if the displays shown in the remote's LCD screen are
customized to reflect the specific characteristics of a
playback source's brand name or the new function
given to a specific button when one remote's controls
are programmed into the AVR remote. The AVR
remote allows you to change the name of either a
master device or any button on the remote using the
following steps.
Renaming a Device
To rename a specific device/input source button, fol-
low these steps. For this example, we will show you
how to rename the Device/Input Selector normally
shown as "TV" to "HDTV TUNER."
1. Press and hold the Program Button
about three seconds while the message shown
in Figure 24 appears in the remote's LCD
Information Display . Release the button
when the red light under the Set Button q
appears.
2. The remote's MAIN MENU message (Figure 25),
will appear in the LCD display and the Set Button
q will remain illuminated in red. Press the
Navigation Button o until RENAME
⁄ ¤
/
appears on the bottom line of the LCD screen,
as shown in Figure 74.
M A I N M E N U
R E N A M E
Figure 74
50 CONFIGURING THE REMOTE
3. At the next menu screen press the
Navigation Button o until RENAME
DEVICE appears on the bottom line of the
LCD screen, as shown in Figure 75. Press the
Set Button q to begin renaming a device.
R E N A M E
R E N A M E D E V I C E
Figure 75
4. The next display screen (Figure 76) is where you
select the device that will be renamed. In our
example, that is the TV button. Press the
Navigation Button o until the name of the
base device appears and then press the Set
Button q.
R E N A M E D E V I C E
T V
Figure 76
5. At the next menu screen you will see the device
name on the bottom line of the display with a
blinking cursor box to the right of the device
Navigation Button o to
‹
name. Press the
return the blinking cursor to the far left side of the
display line. You may then retitle the device name
as shown in the next step.
6. To enter the new name, press the Numeric Keys
. The letters above the numbered buttons
indicate which letter or symbol will appear when
the button is pressed during the renaming
process. The first press of the button will enter the
first letter shown, subsequent presses of the same
button will change the display to the other letters
above that numbered key. For example, since the
first letter we need to rename the input to HDTV
Tuner is an "H", you would locate the "H" above
the "4" button, and press the button twice. The
first press shows a "G," the second press changes
it to an "H. " Consult the table at the end of this
section to see which characters pressing a partic-
ular button generates.
for
7. After you enter the first letter of the new device
name, there are three options for entering the next
character:
a. To enter a letter that requires a different
numeric key to be pressed, simply press that
button. The cursor will automatically move to
the next position and the first letter accessed
by the new button will appear. Following our
example, the next letter needed is a "D," so
you would press the "3" button once.
b. To enter a letter that uses the same numeric
key, you must first press the
Button o to move the blinking cursor block
to the next position. Then press the Numeric
⁄ ¤
/
Key
c. To enter a blank space, press the
Button o twice. The first press will move the
cursor to the right, and the second press will
move the cursor one more space to the right,
leaving a blank space between the last letter
and the next one.
8. Repeat Step 7 as needed to enter all the needed
letters, numbers, characters and spaces.
⁄ / ¤
9. When the text entry is complete, press the
Set Button q. The LCD display will blink
DEVICE RENAMED three times and then
return to normal operation.
Once a device is renamed you will see the new name
on the top line of the remote's LCD display whenever
the Input//Device Selector
any other command/function button on the remote is
pressed after the main Device Selector is pressed.
Note that renaming a device in the remote will not
change the name of the input used by the on-screen
menu system of the AVR 635.
NOTES ON RENAMING DEVICES:
• To move the cursor to the right or left of the display
during the renaming process, press the
Navigation Buttons o as required.
• The table below shows the letters, numbers and
characters that may be accessed by pressing the
Numeric Keys:
Key
1
2
3
4
5
• Renaming a device changes the name of the device
only, not any of the individual key functions within
that device memory. To change the name of an
individual device, follow the instructions in the next
section.
Renaming Individual Keys
Thanks to the programming flexibility of the AVR
remote, an individual button on the remote may be
assigned a feature or function that is different from the
name that appears as the factory default when the
button is pressed. However, with the Rename Key
function it is possible to rename almost any button on
the remote so that when the button is pressed you will
see a more descriptive or appropriate name displayed.
› Navigation
To rename a specific button on the remote, follow
these steps. For this example, we will show you how to
as required to enter the desired letter.
› Navigation
is pressed, or when
‹ ›
/
Characters Key Characters
[,],/,1 6 M,N,O,6
A,B,C,2 7 P,Q,R,S,7
D,E,F,3 8 T,U,V,8
G,H,I,4 9 W,X,Y,Z,9
J,K,L,5 0 -,.,#,0