Table of Contents
Advertisement
Quick Links
Cisco 10000 ESR
AC Power Entry Module Installation
This publication contains instructions for installing the AC Power Entry Module
(PEM) in the Cisco 10000 Edge Services Router (ESR). If you are not familiar
with the Cisco 10000 router, see the Cisco 10000 ESR System Description, and
the Cisco 10000 ESR Hardware Installation Guide for additional information.
Contents
The following sections are included in this configuration guide:
Corporate Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Product Description, page 2
•
Prerequisites and Preparation, page 3
•
Installation Guidelines, page 4
•
Adding or Replacing an AC PEM, page 5
•
FCC Class A Compliance, page 20
•
Cisco Connection Online, page 20
•
Documentation CD-ROM, page 22
•
78-10832-01
Advertisement
Table of Contents
Related Manuals for Cisco Blower Module Cisco 10000 ESR
Summary of Contents for Cisco Blower Module Cisco 10000 ESR
-
Page 1: Table Of Contents
FCC Class A Compliance, page 20 • Cisco Connection Online, page 20 • Documentation CD-ROM, page 22 • Corporate Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Copyright © 2000. Cisco Systems, Inc. All rights reserved. 78-10832-01... -
Page 2: Product Description
Product Description Product Description The AC PEM provides power conversion directly from the facility VAC input power (100 VAC to 240 VAC) to the –48V VDC used internally by the system (see Figure 1). AC power is delivered to the AC PEM from the VAC connection power cable to the power cord attached to the PEM. -
Page 3: Prerequisites And Preparation
Prerequisites and Preparation Before you perform any of the procedures in this guide, Cisco recommends that you: Read the safety guidelines in the next section and review the electrical safety • and ESD-prevention guidelines in the Cisco 10000 ESR Hardware Installation Guide. -
Page 4: Installation Guidelines
Installation Guidelines This warning symbol means danger. You are in a situation that Warning could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. To see translations of the warnings that appear in this publication, refer to the Regulatory Compliance and Safety Information document that accompanied this device. -
Page 5: Adding Or Replacing An Ac Pem
Adding or Replacing an AC PEM This section describes how to add or replace an AC PEM in the Cisco 10000 chassis. It contains the following procedures: Removing the Front Cover, page 5 • Installing a Second AC PEM, page 7 •... -
Page 6: Removing The Front Cover
Adding or Replacing an AC PEM Remove the cover by lifting it up slightly and then pulling it toward you Step 2 (Figure 3). Figure 3 FA N S FA N FA IL U R E M U LT I-F AN FA PO W ER FA U LT... -
Page 7: Installing A Second Ac Pem
Adding or Replacing an AC PEM Installing a Second AC PEM Use the following procedure to install a second AC PEM in the bottom power bay for redundancy. Attach an antistatic wrist strap to your wrist and to an ESD socket on the chassis, Step 1 or to a bare metal surface on the chassis or frame (Figure 4). - Page 8 Adding or Replacing an AC PEM Loosen the captive screws to remove the blank cover from the bottom power bay Step 2 (Figure 5). Figure 5 Captive screws Cisco 10000 ESR AC Power Entry Module Installation Removing the Blank Cover FA NS FA N MU LT I-...
- Page 9 Install the new AC PEM all the way into the power bay to ensure a secure Step 3 connection to the backplane, and then tighten the captive screws (Figure 6). Figure 6 Captive screws 78-10832-01 Installing an AC PEM PO W ER FA U LT PO W ER FA U LT...
- Page 10 Adding or Replacing an AC PEM Connect the power cord from the PEM to your power cord that connects to the Step 4 facility VAC input. Set the AC power cord connectors in a cord strain relief (canoe) to prevent them Step 5 from accidently disconnecting (Figure 7).
- Page 11 Set the power switch to the on (|) position (Figure 8). Step 7 The (green) power LED on the PEM lights indicating that the PEM is on. Figure 8 P O W E R F A U L T Replace the front cover. Step 8 78-10832-01 Setting the AC Power Switch to the On Position...
-
Page 12: Replacing An Ac Pem
Adding or Replacing an AC PEM Replacing an AC PEM Use the following procedure to replace an AC PEM. The illustrations in this guide show how to replace the AC PEM from Note the bottom power bay. The procedure is the same to replace an AC PEM in the top power bay. -
Page 13: Step 2
Power off the PEM you are replacing (Figure 10). Step 2 Do not power off both AC PEMs in a redundant system or the system Caution shuts down and all data traffic stops. Only power off the AC PEM you are replacing. Figure 10 P O W E R F A U L T... - Page 14 Adding or Replacing an AC PEM Remove the PEM power cable from its canoe and disconnect it from the AC input Step 3 power cable (Figure 11). Figure 11 Cisco 10000 ESR AC Power Entry Module Installation AC Power Cord Connectors in Canoes FAN S FAI LUR MU LTI-...
-
Page 15: Figure 12
Loosen the captive screws on the PEM and remove the PEM from the chassis Step 4 using the handle on the faceplate (Figure 12). Figure 12 Captive screw Handle Captive screw 78-10832-01 Removing an AC PEM PO W ER FA U LT PO W ER FA U LT Cisco 10000 ESR AC Power Entry Module Installation... - Page 16 Adding or Replacing an AC PEM Install the new PEM all the way into the power bay to ensure a good connection Step 5 to the backplane, and tighten the captive screws on the PEM (Figure 13). Figure 13 Captive screws Cisco 10000 ESR AC Power Entry Module Installation Installing an AC PEM...
- Page 17 Connect the power cord from the PEM to the power cord that connects to the Step 6 facility VAC input. Set the AC power cord connectors in a cord strain relief (canoe) to prevent them Step 7 from accidently disconnecting (Figure 14). Figure 14 Plug the facility AC input power cord into a power receptacle.
- Page 18 Adding or Replacing an AC PEM Set the power switch to the on (|) position (Figure 15). Step 9 The (green) power LED on the PEM lights indicating that the PEM is on. Figure 15 P O W E R F A U L T Replace the front cover.
-
Page 19: Troubleshooting The Installation
Troubleshooting the Installation Table 1 contains troubleshooting information for the AC PEM: Table 1 Symptom System fails to power on Check that: AC PEM Fault LED is on (yellow) 78-10832-01 AC PEM Troubleshooting Description All AC power cords are properly •... -
Page 20: Fcc Class A Compliance
(That is, make certain the equipment and the television or radio are on circuits controlled by different circuit breakers or fuses.) Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product. - Page 21 Cisco product that is under warranty or covered by a maintenance contract, contact the Cisco Technical Assistance Center (TAC) at 800 553-2447, 408 526-7209, or tac@cisco.com. To obtain general information about Cisco Systems, Cisco products, or upgrades, contact 800 553-6387, 408 526-7208, or cs-rep@cisco.com.
-
Page 22: Documentation Cd-Rom
LightSwitch, MICA, NetRanger, Post-Routing, Pre-Routing, Registrar, StrataView Plus, Stratm, TeleRouter, and VCO are registered trademarks of Cisco Systems, Inc. or its affiliates in the U.S. and certain other countries. All other trademarks mentioned in this document are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any of its resellers.
Need help?
Do you have a question about the Blower Module Cisco 10000 ESR and is the answer not in the manual?
Questions and answers