Page 2
User’s Manual Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Page 3
This display is designed for both you and the planet! TCO Certified is a third party verified program, where every product model is tested by an accredited impartial test laboratory. TCO Certified represents one of the toughest certifications for displays worldwide.
These devices contain recyclable materials, which can be re-decomposed and re-integrated into brand-new marvels. On the contrary, other material can be classified to hazardous and poisoned substances. We strongly encourage you to contact the provided information to recycle this product. For more information, please visit www.hannsg.com...
FEATURES ... 8 CHECKING THE CONTENTS OF THE PACKAGE ... 8 INSTALLATION INSTRUCTIONS ... 9 POWER ... 9 SETTING THE MONITOR ON THE WALL ... 10 MAKING CONNECTIONS ... 11 ADJUSTING THE VIEWING ANGLE ... 12 OPERATING INSTRUCTIONS ... 13 GENERAL INSTRUCTIONS ...
Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or sold with the monitor.
SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears.
User’s Manual BEFORE YOU OPERATE THE MONITOR FEATURES 47cm / 18.5" Wide Screen TFT Color LED Backlight Monitor Crisp, Clear Display for Windows ® EPA ENERGY STAR GP Green Product Ergonomic Design Space Saving, Compact Case Design...
3. Snap the monitor into its base. A clear click sound will affirm that the base is connected correctly. 4. Verify that the monitor is securely attached to the base by looking at the bottom of the base and making sure that the clips are fully engaged in the base.
The pitch of the mounting holes is 100mm horizontally and 100mm vertically. The screws type required is metric: M4, 10mm length. The Monitor stand base can be screwed on a table or a hard surface using the hole on the back of the stand base.
CONNECTING TO A PC Turn off your computer before performing the procedure below. 1. Connect one end of the VGA cable to the back of the monitor and connect the other end to the computer’s VGA port. 2. Connect the audio cable between the monitor's audio input and the PC's audio output (green port).
ADJUSTING THE VIEWING ANGLE For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s angle to your own preference. Hold the stand so you do not topple the monitor when you change the monitor’s angle.
OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located on the front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences.
User’s Manual FRONT PANEL CONTROL Power Button: Press this button to switch ON/OFF of monitor’s power. Power Indicator: — Power On mode. Green Orange — Power Saving mode. MENU / RETURN: 1. Turn the OSD menu on/off or return to the previous menu.
Page 15
** The screen resolutions available will depend on the purchased model. NOTES: Do not install the monitor in a location near heat sources such as radiators or air dusts, or in a place subject to direct sunlight, or excessive dust or mechanical vibration or shock. ...
User’s Manual HOW TO ADJUST A SETTINGS BRIGHTNESS/ CONTRAST BRIGHTNESS CONTRAST X-CONTRAST PRESET MODE INPUT SETTING INPUT SETTING AUTO SEARCH COLOR SETTING WARM NATURE (6500K) COOL USER IMAGE SETTING AUTO ADJUST ASPECT RATIO Adjust the brightness value of the display according to your preference.
Page 17
H-POSITION V-POSITION CLOCK PHASE SHARPNESS VIDEO MODE RESPONSE TIME OSD SETTING LANGUAGE H-POSITION V-POSITION TRANSPARENCY display, which does not ensure the image is shown as is or in initial scale. 「FIT」 indicates scaling by the proportion of original images, which may cause the screen showing black bands. availability of this function depends upon the selected model] Select the 「H-POSITION」...
Page 18
AUDIO INPUT to HDMI; if no sound is outputted, it is recommended to select AUDIO INPUT as PC, and make sure the PC audio output cable is connected to monitor’s LINE IN (or AUDIO IN) port. [For HDMI Input only] Select the 「VOLUME」...
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The DDC2B is a bidirectional data channel based on the I²...
CAPS LOCK LED. The LED should either turn ON or OFF after hitting the CAPS LOCK key. *Inspect the monitor’s video cable and make sure that none of the pins are bent. * Adjust pixel frequency CLOCK and PHASE or press hot-key ( i Button).
Page 21
User’s Manual INPUT as a PC option, and make sure PC audio output cable is connected to monitor’s LINE IN port(or AUDIO IN port). [For HDMI Input only]...
User’s Manual ERROR MESSAGE & POSSIBLE SOLUTIONS CABLE NOT CONNECTED: 1. Check that the signal-cable is properly connected, If the connector is loose, tighten the connector’s screws. 2. Check the signal-cable’s connection pins for damage. INPUT NOT SUPPORT : Your computer has been set to unsuitable display mode, set the computer to display mode given in the following table.
*** The above specification is subject to actual product specification and is subject to change without prior notice. NOTES: The Maximum Resolution will depends on the display card supporting. Related issue can refer to www.hannsg.com FAQ section. TFT Color LED 47cm / 18.5" Diagonal 0.300mm(H) x 0.300mm(V) 24KHz –...