Subscribe to Our Youtube Channel
Related Manuals for Haier XPB90-0713S
Summary of Contents for Haier XPB90-0713S
- Page 1 Twin-tub Washing Machine User's manual This manual is for XPB90-0713S Please read this manual carefully before using. Retain it for future reference.
-
Page 2: Table Of Contents
Contents Specification- - - - - - - - - - - - - - - - - - - - the 2nd cover Names of the parts - - - - - - - - - - - - - - - - - 1 Safety precautions - - - - - - - - - - - - - - - - - 2 Installation and adjustment - - - - - - - - - - - 4... -
Page 3: Names Of The Parts
Names of the parts Wash selector Wash timer Water-filling entrance Control panel Overflow filter Water level adjusting lever Wash tub Protecting cover Valve cover Pulsator Wash tub cover Drain hose Base frame Notes: All illustrations in this manual are given for reference only. Your products and accessories may show differences from these illustrations due to our continuous improvement. -
Page 4: Safety Precautions
Safety precautions Please insert the power cord into special receptacle with rated vol- tage. Be sure to use single-phase three pins receptacle. The earthing terminal of the receptacle must be earthed reliably. If possible, please adopt electric leakage protector. If the power cord is bad, to avoid risk it is required to replace it by the technicians of our special shop or the after-sale service department. - Page 5 It is suggested to use foamless washing powder. Please don t use the washer in the environment below 0 C. If the washer is below 0 C, the washer s water inlet system and draining system will be frozen ,then result in the damaged of the whole machine.
-
Page 6: Installation And Adjustment
Installation and adjustment Please install and adjust the machine according to the requirement of the manual. It is very important to your security and correct operating the machine. Install the lint filter After opening the package, please take out the lint filter from the document bag, install it to the overflow filter of the wash tub. -
Page 7: How To Change The Direction Of The Drain Hoses
How to change the direction of the drain hoses Figure 1 indicates the ex factory installation position of the drain hose. Extend the drain hose from the side of spin tub Put soft items on the ground. Lean the machine down gently with the front surface facing the ground. -
Page 8: Preparation Before Washing
Preparation before washing Pay attention to followings before washing the laundries Check if Clear the the laundries pocket. Take has special out the coins, requirement sand, hairpins on washing etc. a. Check if the laundries are applicable for washing with machine. b. -
Page 9: The Musts In Washing
The musts in washing Usage of the detergent How to use the whitener Fill water to decided level. Dilute the whitener with container. Pour it slowly into the washing tub. Avoid using whitener on laun- dries with color or pattern as they are prone to lose color. -
Page 10: Washing Sequence
Washing sequence Wash timer (To set to below 2 minute, first set to 6 minute then Water inlet turn it back. it can increase the service life of the timer). WASH TIMER Wash 1. Fill the water and add the dissolved washing powder to make the water level reach the preset position. -
Page 11: Rinse With Water-Filling
Rinsing Rinse with water-filling 1.Put the laundries into the wash tub. Select suitable current according to the laundries. 2.Adjust the water level Set the water level with water level adjusting lever according to the laundries quantity. Then fill suitable water continuously. 3.Rinse Adjust the wash timer to 5-7 minutes to do rinsing. - Page 12 Ï ´ µ Ó Ð ë Ö ª Spinning 1.Put the laundries into the spin tub evenly and smoothly. 2.Spin (1) Put the gland in properly. Please put in the gland properly even if the laundries quantity is small. Push Gland Proper The laundries...
-
Page 13: Disposal After Washing
Disposal after washing After using, please clean the lint and foreign materials of the lint filter and overflow filter in time. Otherwise it may influence your using the machine. Please first pull off the power plug from the receptacle before cleaning. Cleaning the lint filter The lint filter must be used during washing. -
Page 14: Cleaning The Overflow Filter
Cleaning the overflow filter 2. Take off the corrugation pipe. Dismantle the upper part of the corrugation pipe overflow filter ( as indicated in Figure 1). 3. Cleaning the overflow filter Clean the lint around the filter and flush with tap water. 4. -
Page 15: Trouble-Shooting Answer To Question
Disposal of the complete unit Wipe the complete unit with soft cloth twisted dry. Wipe with neutral detergent if too dirty. Do not wash it directly by water. Thinner Petrol Alcohol Trouble-shooting Answer to question If the laundries fall to the outer side of the spin tub If the laundries fall to the outer side of the spin tub, contact the after-sales service department. -
Page 16: Packing List
Trouble-shooting Answer to question (If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company.
Need help?
Do you have a question about the XPB90-0713S and is the answer not in the manual?
Questions and answers