Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Compac LL160S
Summary of Contents for Compac LL160S
- Page 1 Laser Version: LL160S Date of issue: 17 November 2014 Compac Industries Ltd. 52 Walls Road. Penrose. Auckland 1061. New Zealand. PO Box 12 417. Penrose. Auckland 1642. New Zealand. Tel: +64 9 579 2094 Fax: +64 9 579 0635 info@compac.co.nz...
-
Page 2: Table Of Contents
11.2 Standalone Operation ....................... 12 Spare Fuses ........................12 Precautions if Using Generator Power .................. 12 Error Messages ....................... 13 LL160S Spare Parts ......................14 Product Details ........................ 15 Contact Details ........................ 15 Notes ..........................15 Revision History ....................... 16 G:\Masters\Installation Sheets\Laser\LL160S Installation Sheet.doc... -
Page 3: Conditions Of Use
Unless otherwise noted, references to brand names, product names, or trademarks constitute the intellectual property of the owner thereof. Subject to your right to use the unit, Compac does not convey any right, title, or interest in its intellectual property, including and without limitation, its patents, copyrights, and know-how. -
Page 4: Footprint
1½" BSP Sockets. Nozzle Holder Rear Outlet Side B Nozzle 8 Mounting Holder Holes Ø20 Front Outlet 1½" BSP Side A Socket Footprint Plan View LL160S G:\Masters\Installation Sheets\Laser\LL160S Installation Sheet.doc Page 4 of 16... -
Page 5: Static Electricity Precautions
This is not a recommended alternative to wearing an anti-static wrist strap. Note: Compac Industries Limited reserves the right to refuse to accept any circuit boards returned, if proper anti-static precautions have not been taken. -
Page 6: Triac Dip-Switches
These switches are set in the factory and should not be changed. If they are accidentally changed these are the correct settings for Laser Pump applications. Note: They are 3 position switches Pump (Motor triac fitted) Centre G:\Masters\Installation Sheets\Laser\LL160S Installation Sheet.doc Page 6 of 16... -
Page 7: Electrical Connections
Pump supplying side B to terminal marked T4 If both sides are required to switch the same submersible pump then T1 and T4 should be linked together. Note: Dispensers do not use the terminals marked LOAD 1 & 2. G:\Masters\Installation Sheets\Laser\LL160S Installation Sheet.doc Page 7 of 16... -
Page 8: Dispensing Hoses And Nozzles
Configuration Code 10.1 The configuration code has been set at Compac and should not be changed In the event of it being lost and having to be re-entered the configuration is written on the yellow label on the C4000 processor board cover. - Page 9 Press and release the Parameter switch 8 or more The price for side ‘B’ is shown as ‘PX.XXX’ on the times in quick succession litres display and ‘Prb’ is displayed on the money display. Repeat steps 3 to 5 above. G:\Masters\Installation Sheets\Laser\LL160S Installation Sheet.doc Page 9 of 16...
-
Page 10: K-Factor Switch Settings
J 9 Power for KG Meters J15: Not used Side A J4: Input from KG Meter J10: Totes J16: Not used Side B J5 : Not Used J11: Buzzer J17 Backlighting J6 Not used J12 Nozzle Switches G:\Masters\Installation Sheets\Laser\LL160S Installation Sheet.doc Page 10 of 16... -
Page 11: Calibration (K-Factor)
Existing Factor 10.00 Existing Factor Change the existing 'K' Factor to this new value. Sealing the K-Factor switch 11.2 After calibration the K-factor switch should be sealed as shown G:\Masters\Installation Sheets\Laser\LL160S Installation Sheet.doc Page 11 of 16... -
Page 12: Standalone Operation
3) For units where the generator starts and stops on demand, install a delay timer or PLC to automatically isolate the unit until the operating speed and consistent power output is achieved. 4) Isolate the unit before shutting down the generator. G:\Masters\Installation Sheets\Laser\LL160S Installation Sheet.doc Page 12 of 16... -
Page 13: Error Messages
Configuration Lost Reconfigure C4000 refer to C4000 manual Err 12 C4000 memory failure. Change memory IC. F-AD-DS1225 (not applicable to Futra) Display error Check display cable for loose wires/crimps Replace display PCB G:\Masters\Installation Sheets\Laser\LL160S Installation Sheet.doc Page 13 of 16... -
Page 14: Ll160S Spare Parts
(electronics only) F-METER-125/250E Solenoid (complete) F-SOLND-S20-2P1X Solenoid service parts Coil - F-SOL-20P1-COIL Main body kit - F-SOL-20P1-MBKT Top body kit - F-SOL-20P1-TBKT Filter Element F-FILTER-926170 C4000 Power Supply (does not include box) F-CP-C4PWR-ASSEM G:\Masters\Installation Sheets\Laser\LL160S Installation Sheet.doc Page 14 of 16... -
Page 15: Product Details
Phone E-mail Address 1 Address 2 Notes Manufacturer Contact The Compac Laser Dispenser is designed and Details manufactured by: Compac Industries Limited 52 Walls Road, Penrose, Auckland 1061, New Zealand P.O. Box 12-417, Penrose, Auckland 1641, New Zealand Phone: + 64 9 579 2094 Fax: + 64 9 579 0635 www.compac.co.nz... -
Page 16: Revision History
Updated wiring info & spare parts 17 October 2013 Added sump info in accordance with EPA. File ref. COM 09 29 29 August 2014 Added new front page footer and pump outlet size. G:\Masters\Installation Sheets\Laser\LL160S Installation Sheet.doc Page 16 of 16...
Need help?
Do you have a question about the LL160S and is the answer not in the manual?
Questions and answers