IMPORTANT REMOTE CONTROL INFORMATION ...2 Warning and cautions ...3 Location of controls ...4 Using the remote control ...7 Basic operation Switching on/off the TV set Searching channels ...9 Full automatic mode...9 Semi-automatic search...10 Manual fine tune...11 Program skip ...12 Watching TV ...13...
/ navigation buttons on the remote controller. DVD Function Button Please note the DVD function button on the remote control switches the unit between TV and DVD, after watching a DVD Disc press the DVD button to return to TV mode.
AVOID excessive warm locations to prevent possible damage to the cabinet or component failure. CONNECTION This TV receiver can be connected to 230V- 50Hz, NEVER connect to DC supply or any other power. AUTOMATIC DEGAUSSING All colour television receivers are sensitive to magnetic influences, usually caused by either moving the receiver from one place to another or using certain electrical appiiances near the receiver.
CABINET, the power cord must be pulled out from the wall then wipe the receiver with a dry soft cloth. "inside work" on your tv must DANGER Invisible laser radiation when open and interlock failed or defeated. avoid direct exposure to laser beam.
Page 6
IMPORTANT SAFEGUARDS PREFITTED MAINS PLUGS For you convenience a mains plug has been fitted to this appliance. For your safety please observe the following information. 1. Should the fuse in the plug fail remove the plug from the wall socket and replace the fuse with a 5Amp ASTA approved to BS 1362 fuse.
Page 7
1. Front AV: AV1 signal input in TV mode. Rear AV interface: AV2 signal input. 3. SCART1: in TV mode, containing one AV2 signal input, one RGB signal input and one AV output. SCART2; in DVD mode, containing one AV (CVBS) output.
" 1 To turn the set off to Standby press button on the remote control. AUTO 2 To turn off the TV fully, press the Power button and release. Auto switch-off function Should the signal input from the aerial be interrupted for more than 5 minutes, the TV will automatically switch to "Standby".
- automatic and manual fine TUNE. In this section, how to use the remote control to set the channel is explained. You can also use the buttons on the TV to set the channel. Full automatic mode Automatic search...
Searching channels ( ) Continued Semi-automatic search Semi-automatic search 1 Press the P+/- buttons or PROGRAM NUMBER 0-9 buttons to choose desired channels I.E. channel 1 TUNE 2 Press the TUNE button, the TUNE menu will be shown on the right of the screen. Press the P+/- P...
Searching channels ( ) Continued Manual fine tune Manual fine tune If the picture and/or sound are poor, try using the FINE TUNE feature. reception is poor. P + 1 Press the P+/- buttons or PROGRAM NUMBER 0-9 button to choose desired V...
Searching channels ( ) Continued Programme skip Programme skip During Auto tune some channels may have been received which are of poor quality, noisy or ghosting. These can be removed with Program Skip . 1 Press the P+/- buttons or P...
Press the P- button to decrease channel number. P + Adjust the Volume level Press the V / buttons on the remote or the front of the TV V + MENU set to adjust the volume level. The range is 0~100. When the volume buttons are pressed the volume level is displayed automatically on the TV screen.
Auto program scan 1 Press the SCAN button to SCAN scan through all the memorized TV channels. The scan will pause for about 2 seconds on each channel. 2 If you want to stop the function during auto scanning, simply press the SCAN button again.
"RICH", "USER","LISTEN", "SOFT" ) can be selected in turn. The 5 modes are Listen-This is a new feature that blacks out the TV Soft-Designed for night time low light viewing; Standard -Designed for rooms that have good all round Rich-Designed for rooms with high ambient lighting such User-A spare setting that can be adjusted to personal tastes.
Convenient picture and sound control functions ( ) Continued Noise Reduce Picture Noise & Grain Reduction Circuit. (Use only on poor reception) Black stretch and noise reduce How to select BLACK STRETCH PICTURE 1 Press the PICTURE right display on the screen. P...
Convenient picture and sound control functions ( ) Continued Mute Sound mute 1 Press the MUTE button on the remote control to turn off the MUTE sound. MUTE will appear on the top left of the display. 2 Press MUTE again to turn the sound back on.
定时关机功能 Clock setting and timer on/off functions Clock setting The clock will only work if the TV set is left turned on or placed in its standby mode. When the set is TIME disconnect from the power supply or is turned off by...
Time functions ( ) Continued Sleep timer and program preset Sleep timer The TV has 18 option settings for TIME " Sleep timer , each setting has a time value of 10 minutes. 1 Press the TIME button, and the TIME menu display on the screen.
CHILD LOCK function "ON" V + M E N U NOTE: All the control panel buttons on the front of the TV are disabled when CHILD LOCK is turned on. The power switch will still turn the TV set off. "...
3 Press AVL function "ON" or "OFF" Calendar function FUNCTION Enables the TV sets internal calendar to be set. 1 Press the Function button, the Function menu will be displayed on the right of the screen. 2 Press the P+/- buttons to select "CALENDAR"...
Position exchange function Exchange Exchange This feature enables TV programs that may be on a wrong TV channel number to be swapped/exchanged. This feature is very useful when Automatic Search Tuning has been used, to reallocate the found programs to the correct channel numbers.
(cable networks, satellite channels, etc.).Teletext button on remote can be used in TV mode only. When using DVD or selecting AV1 /AV2,please do not press the text button.
Page 25
Continued Teletext Cancel mode This feature allows the TV picture to be displayed while next page to be searched is entered and found. Only the top teletext line is displayed until the page is found. Press the button to hide the teletext information. Either press the button or the Text button to exit the cancel display mode.
Basic Playback Basic Playback Preparations Press the TV/DVD button on the remote control or the TV to enter the DVD status. Basic playback 1. Press OPEN/CLOSE to open the disc tray, place a disc on the disc tray. There are two different disc sizes. Place the disc in the correct guide on the disc tray.
Advanced Playback Advanced Playback IMPORTANT NOTE: ALL DESCRIBED FUNCTIONS ARE FOR DVD DISCS. IF YOU PLAY OTHER FORMATS, THE OPERATION AND DISPLAY ON SCREEN MAY VARY. SUBTITLE Press " ", the screen will display "SUBTI- SUBTITLE TLE 01/XX XXXXX", "01" indicates the ordinal number of this language;...
Special Function Playback JPEG DISC PLAYBACK When a disc containing standard JPEG picture files is inserted into the player, a navigation menu will be displayed automatically. Use the UP and DOWN cursor buttons to select a file then press PLAY/ENTER. The slide show will commence. Press PREVIOUS or NEXT to move between pictures.
: 16 9 You may select this if you have a widescreen (16:9) TV. Back bars may still appear above and below the picture even if using a widescreen TV. This is because some film directors prefer to use ultra widescreen aspect ratios e.g.
Page 30
LB Angle Mark On OSD Lang ENG Spdif Output Captions On Screen Saver Off ..General Setup Page.. TV Display Angle Mark OSD Lang Spdif Output Caption Screen Saver Off ..General Setup Page.. TV Display Angle Mark OSD Lang Spdif Output...
Page 31
Preference Page The Preference Page is only available when there is no disc in the player. These settings are applied consistently to all discs which are inserted and played. TV TYPE: This player SETUP supports different TV output, including MULTI(Auto), NTSC, and PAL systems.
Page 32
PLAY/ENTER Note: Some functions may not be available depending on the type of disc. Press the OPEN/CLOSE button to close the DVD draw after screen saver has activated. Resets all settings ..Preference Page.. TV Type Auto Parental Password Default Reset...
Playable Discs The following discs can be played: You cannot play discs other than those listed above. You cannot play discs of non-standardized discs, even if they may be labelled as above. The performance of CD-R or CD-RW disc is depend on the way of disc-burning. In a few cases, their performance may be not very well or even no performance.
Disc Protection and DVD Characteristics Compare DVD disc with other discs: Encode Digital/MPEG method Single- Double Single- side -side side Capacity single- single double- layer -layer layer 4.7G 8.5G 9.4G Playing Time minutes minutes minutes 12cm/8cm Disc diameter Horizontal More than 500 line resolution Picture Multiple kinds...
Connecting the TV set to the other video and audio equipment Connecting to the other video and audio equipment You can attach other equipment such as another TV or other audio amplification equipment to the scart/digital coaxial sockets at the rear of the set to enjoy higher quality sound and picture.
No disc on screen. DVD picture skips Dirty disc. and jumps. Remedy Fault Press P+ or P- on handset. TV may be in Child lock . Press Picture button on " handset. Adjust brightness level. Check aerial connection. Aerial may be damaged.
Specifications The specifications offered you here are only for reference and, with the improvement of the products ,there may be some different between the description and the practicality. Specifications M o d e l Colour system PAL, NTSC PLAYBACK Sound system Picture tube 14 colour picture tube (34cm viewable) "...
Need help?
Do you have a question about the GTV14T5DVD and is the answer not in the manual?
Questions and answers