Maintenance - DeWalt DCPR320 Instruction Manual

English
1. Keeping your hands and other body parts away from the
blade, push the lock‑off button
lock‑off switch 3 then squeeze the trigger switch
2. The cutting blade 6
cycle is complete you must release the trigger switch
3. To make repeated cuts, squeeze the trigger
switch 1 again while continuing to hold down lock off
switch 3 .
4. To turn the tool off, release the trigger switch
lock‑off switch 3 .
nOTE: In order to keep the unit powered on, you must
continue to squeeze the lock‑off switch
long the tool will time out and will need to release
switches and start again.
nOTE: If the lock‑off button
unintentionally depressed without squeezing the trigger
switch 1 , the tool will power off.
LED Worklight (Fig. A)

CAUTION:
Serious eye injury could result.
The LED worklight 5 is activated when the trigger switch
is depressed, and will automatically turn off 20 seconds after
the trigger switch is released. If the trigger switch remains
depressed, the worklight will remain on.
nOTE: The worklight is for lighting the immediate work
surface and is not intended to be used as a flashlight.
Pruning Instructions (Fig. A, F)

DANGER:
parts away from the blade. Contact with the blade
will result in serious personal injury.

WARNING:
observe the following:
• Read instruction manual before using. Save
instruction manual.
• Check the shrub for foreign objects such as wires or
fences before each use.
• Keep hand on firmly on tool and other hand far
away from cutting action. Don't overreach.
• Do not use under wet conditions.

CAUTION:
branches greater than 1.25" (32 mm). Use the pruner
only for cutting normal shrubbery around houses
and buildings.
Working Position (Fig. F)
Maintain proper footing and balance and do not overreach.
Wear safety goggles, non‑skid footwear and gloves when
pruning. Hold the tool firmly. Always hold the pruner, as
shown in Fig. F. Refer to Proper Hand Position for more
information. Never hold the tool by the blades.
8
2 down and squeeze the
will make a cut cycle. Once this
1
3 . If held too
2 or lock‑off switch
Do not stare into worklight.
Keep hands and other body
To guard against injury,
Do not use blade to cut
1. Position the branch to be cut between the cutting
blade 6
1 .
2. Push the lock‑off button
off switch
1 .
3. The cutting blade
branch off.
nOTE: Cut branches at an angle for a cleaner cut.
4. Release the trigger switch.
nOTE: If more branches need to be cut, at the same time,
and the
the lock‑off switch
trigger switch

MAINTENANCE


WARNING:
3 are
personal injury, turn unit off and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
1 care and regular cleaning.
Removing and Installing Blade (Fig. A, G, H)

DANGER:
REASSEMBLING THE BLADE SYSTEM, ENSURE EACH
PART IS REINSTALLED CORRECTLY, AS DESCRIBED
BELOW. IMPROPER ASSEMBLY OF THE BLADE OR
OTHER PARTS OF THE BLADE SYSTEM CAN CAUSE
SERIOUS INJURY.

DANGER:
personal injury, turn unit off, remove battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause serious personal injury.

WARNING:
protection. Be careful of the sharp edges on the blade.
Replacement blades are available from your nearest
authorized service center. This pruner requires replacement
blade DWZPRB300.
1. Remove the battery.
2. Wear proper eye protection and gloves and be careful
not to cut yourself.
3. Place the product on a smooth, level surface.
4. Using the supplied hex wrench
blade screw
will allow for easier removal and assembly of the cutting
blade 6
5. Flip the product onto its other side.
6. Using the hex wrench
screw
12
and fixed blade 7 .
2 down and squeeze the lock‑
3 then squeeze the trigger switch
6 will make a cut cycle and cut the
3 can be held down and actuate the
1 as needed. Otherwise, repeat steps 1‑4..
To reduce the risk of serious
RISK OF INJURY. WHEN
To reduce the risk of serious
Use gloves and proper eye
10
11 one full turn as shown in Fig. G. This
.
remove the cutting blade
10
and nut as shown in Fig. H.
13
1 .
loosen the fixed