Sony MEX-BT38UW Service Manual
Hide thumbs
Also See for MEX-BT38UW:
- Operating instructions manual (72 pages) ,
- Specification sheet (2 pages) ,
- Installation/connections (2 pages)
Table of Contents
Advertisement
Quick Links
SERVICE MANUAL
Ver. 1.0 2009.11
AUDIO POWER SPECIFICATIONS
CEA2006 Standard
Power Output: 17 Watts RMS
4 at
4 Ohms < 1% THD+N
SN Ratio: 82 dBA
(reference: 1 Watt into 4 Ohms)
Tuner section
FM
Tuning range: 87.5 – 107.9 MHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 150 kHz
Usable sensitivity: 10 dBf
Selectivity: 75 dB at 400 kHz
Signal-to-noise ratio: 70 dB (mono)
Separation: 40 dB at 1 kHz
Frequency response: 20 – 15,000 Hz
AM
Tuning range: 530 – 1,710 kHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 25 kHz
Sensitivity: 26 μV
Tuner section
FM
Tuning range: 87.5 – 108.0 MHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 150 kHz
Usable sensitivity: 10 dBf
Selectivity: 75 dB at 400 kHz
Signal-to-noise ratio: 70 dB (mono)
Separation: 40 dB at 1 kHz
Frequency response: 20 – 15,000 Hz
MW/LW
Tuning range:
MW: 531 – 1,602 kHz
LW: 153 – 279 kHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 25 kHz
Sensitivity: MW: 26 μV, LW: 45 μV
Sony Corporation
9-889-696-01
2009K0500-1
Audio&Video Business Group
©
2009.11
Published by Sony Techno Create Corporation
Photo: MEX-BT3800U
Model Name Using Similar Mechanism
CD Mechanism Type
Optical Pick-up Name
SPECIFICATIONS
Tuner section
FM
Tuning range:
87.5 – 108.0 MHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 150 kHz
Usable sensitivity: 10 dBf
Selectivity: 75 dB at 400 kHz
Signal-to-noise ratio: 70 dB (mono)
Separation: 40 dB at 1 kHz
Frequency response: 20 – 15,000 Hz
MW/LW
Tuning range:
MW: 531 – 1,602 kHz
LW: 153 – 279 kHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 25 kHz
Sensitivity: MW: 26 μV, LW: 45 μV
Tuner section
FM
Tuning range:
87.5 – 108.0 MHz (at 50 kHz step)
87.5 – 107.9 MHz (at 200 kHz step)
FM tuning interval: 50 kHz/200 kHz switchable
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 150 kHz
Usable sensitivity: 10 dBf
Selectivity: 75 dB at 400 kHz
Signal-to-noise ratio: 70 dB (mono)
Separation: 40 dB at 1 kHz
Frequency response: 20 – 15,000 Hz
AM
Tuning range:
531 – 1,602 kHz (at 9 kHz step)
530 – 1,710 kHz (at 10 kHz step)
AM tuning interval: 9 kHz/10 kHz switchable
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 25 kHz
Sensitivity: 26 μV
MEX-BT38UW/BT3800U/
BT3807U/BT3850U
Tuner section
FM
Tuning range:
87.5 – 108.0 MHz (at 50 kHz step)
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 150 kHz
Usable sensitivity: 10 dBf
Selectivity: 75 dB at 400 kHz
Signal-to-noise ratio: 70 dB (mono)
Separation: 40 dB at 1 kHz
Frequency response: 20 – 15,000 Hz
AM
Tuning range:
531 – 1,602 kHz (at 9 kHz step)
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 25 kHz
Sensitivity: 26 μV
CD Player section
Signal-to-noise ratio: 120 dB
Frequency response: 10 – 20,000 Hz
Wow and flutter: Below measurable limit
USB Player section
Interface: USB (Full-speed)
Maximum current: 500 mA
Wireless Communication
Communication System:
Bluetooth Standard version 2.0
Output:
Bluetooth Standard Power Class 2 (Max. +4 dBm)
Maximum communication range:
1
Line of sight approx. 10 m (33 ft)*
Frequency band:
2.4 GHz band (2.4000 – 2.4835 GHz)
Modulation method: FHSS
2
Compatible Bluetooth Profiles*
:
A2DP (Advanced Audio Distribution Profile)
AVRCP (Audio Video Remote Control Profile)
HFP (Handsfree Profile) 1.5
HSP (Headset Profile)
US Model
MEX-BT38UW/BT3800U
Canadian Model
AEP Model
UK Model
MEX-BT3800U
Russian Model
MEX-BT3807U
E Model
MEX-BT3850U
MEX-BT3700U/BT3750U/BT4700U
MG-101Z-188//Q
DAX-25A
*1 The actual range will vary depending on factors
such as obstacles between devices, magnetic
fields around a microwave oven, static electricity,
reception sensitivity, antenna's performance,
operating system, software application, etc.
*2 Bluetooth standard profiles indicate the purpose of
Bluetooth communication between devices.
Power amplifier section
Output: Speaker outputs (sure seal connectors)
Speaker impedance: 4 – 8 ohms
Maximum power output: 52 W
4 (at 4 ohms)
General
Outputs:
Audio outputs terminal (front/rear)
Subwoofer output terminal (mono)
Power antenna (aerial) relay control terminal
Power amplifier control terminal
Inputs:
BUS control input terminal
BUS audio input terminal
Telephone ATT control terminal
Remote controller input terminal
Antenna (aerial) input terminal
MIC input terminal
AUX input jack (stereo mini jack)
USB signal input connector
Tone controls:
Low: ±10 dB at 60 Hz (XPLOD)
Mid: ±10 dB at 1 kHz (XPLOD)
High: ±10 dB at 10 kHz (XPLOD)
Power requirements: 12 V DC car battery
(negative ground (earth))
Dimensions: Approx. 178
50
179 mm
1
1
(7
/
2
7
/
in) (w/h/d)
8
8
Mounting dimensions: Approx. 182
53
162 mm
1
1
1
(7
/
2
/
6
/
in) (w/h/d)
4
8
2
Mass: Approx. 1.2 kg (2 lb 11 oz)
Supplied accessories:
Card remote commander: RM-X304
Parts for installation and connections (1 set)
Design and specifications are subject to change
without notice.
AUDIO SYSTEM
Advertisement
Table of Contents
Related Manuals for Sony MEX-BT38UW
Summary of Contents for Sony MEX-BT38UW
- Page 1 Intermediate frequency: 25 kHz Antenna (aerial) terminal: Sensitivity: 26 μV External antenna (aerial) connector Intermediate frequency: 25 kHz Sensitivity: MW: 26 μV, LW: 45 μV AUDIO SYSTEM Sony Corporation 9-889-696-01 2009K0500-1 Audio&Video Business Group © 2009.11 Published by Sony Techno Create Corporation...
- Page 2 Do not touch the soldering iron on the same conductor of the TIONNEMENT. NE REMPLACER CES COMPOSANTS QUE circuit board (within 3 times). PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DON- • Be careful not to apply force on the conductor when soldering NÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS...
-
Page 3: Table Of Contents
MEX-BT38UW/BT3800U/BT3807U/BT3850U TABLE OF CONTENTS SERVICING NOTES ..........GENERAL ..............DISASSEMBLY 3-1. Disassembly Flow ............13 3-2. Cover ................13 3-3. CD Mechanism Deck (MG-101Z-188//Q) ..... 14 3-4. ANTENNA Board ............14 3-5. MAIN Board ..............15 3-6. SERVO Board ..............15 3-7. -
Page 4: Servicing Notes
MEX-BT38UW/BT3800U/BT3807U/BT3850U SECTION 1 SERVICING NOTES UNLEADED SOLDER NOTES ON HANDLING THE OPTICAL PICK-UP Boards requiring use of unleaded solder are printed with the lead- BLOCK OR BASE UNIT free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with... - Page 5 MEX-BT38UW/BT3800U/BT3807U/BT3850U NOTE FOR REPLACEMENT OF THE BT BOARD MODEL IDENTIFICATION When repairing, the complete BT board (Part No. A-1641-142-A) – Bottom View – should be replaced since any parts in the BT board cannot be re- paired. NOTE FOR REPLACEMENT OF THE SERVO BOARD When repairing, the complete SERVO board (Part No.
- Page 6 2. If the board needs to be replaced 7. After switching the source of the MEX-BT38UW/BT3800U/ • Return to the factory shipping mode. BT3807U/BT3850U)to other than BT PHONE (e.g. TUNER) to check that a sound is generated, make a call to the cellular phone connected to the set.
-
Page 7: General
MEX-BT38UW/BT3800U/BT3807U/BT3850U SECTION 2 This section is extracted GENERAL from instruction manual. (BT38UW/BT3800U: US and Canadian models) ... - Page 8 MEX-BT38UW/BT3800U/BT3807U/BT3850U ...
- Page 9 MEX-BT38UW/BT3800U/BT3807U/BT3850U (BT3800U: AEP, UK /BT3807U) ...
- Page 10 MEX-BT38UW/BT3800U/BT3807U/BT3850U ...
- Page 11 MEX-BT38UW/BT3800U/BT3807U/BT3850U (BT3850U) Ω ...
- Page 12 MEX-BT38UW/BT3800U/BT3807U/BT3850U ...
-
Page 13: Disassembly
MEX-BT38UW/BT3800U/BT3807U/BT3850U SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below. 3-1. DISASSEMBLY FLOW FRONT PANEL SECTION Note: Illustration of disassembly is omitted. 3-2. COVER (Page 13) 3-3. CD MECHANISM DECK (MG-101Z-188//Q) (Page 14) 3-4. ANTENNA BOARD 3-6. -
Page 14: Cd Mechanism Deck (Mg-101Z-188//Q)
MEX-BT38UW/BT3800U/BT3807U/BT3850U 3-3. CD MECHANISM DECK (MG-101Z-188//Q) CD mechanism deck (MG-101Z-188//Q) two screws (PTT2.6 × 4) connector (CN350) bracket (CD) screw (PTT2.6 × 6) connector (CN110) screw two screws (PTT2.6 × 6) (PTT2.6 × 6) 3-4. ANTENNA BOARD two claws lead wire with connector... -
Page 15: Main Board
MEX-BT38UW/BT3800U/BT3807U/BT3850U 3-5. MAIN BOARD connection cord (MIC) (external microphone) (J801) connector (CN811) screw screw (PTT2.6 × 8) screw (PTT2.6 × 8) (PTT2.6 × 8) fuse (blade type) (auto fuse) (10A/32V) (FU701) three ground point screws connection cord (RCA) (PTT2.6 × 6) -
Page 16: Chassis (T) Sub Assy
MEX-BT38UW/BT3800U/BT3807U/BT3850U 3-7. CHASSIS (T) SUB ASSY two screws (M 1.7 × 2.5) two screws (M 1.7 × 2.5) chassis (T) sub assy claw 3-8. ROLLER ARM ASSY roller arm assy gear (RA1) spring (RAL) washer spring (RAR) -
Page 17: Chassis (Op) Assy
MEX-BT38UW/BT3800U/BT3807U/BT3850U 3-9. CHASSIS (OP) ASSY chassis (OP) assy tension spring (KF) two coil springs (damper) (natural) coil spring (damper) (green) slider (R) lever (D) gear (LE1) 3-10. CHUCKING ARM SUB ASSY chucking arm sub assy spring Note 1: Have this portion receive the chassis. -
Page 18: Sled Motor Assy
MEX-BT38UW/BT3800U/BT3807U/BT3850U 3-11. SLED MOTOR ASSY three serration screws (M 2 × 3) sled motor assy spring turn table spring stand Note 2: Never remove these parts since they were adjusted. bearing (F) stand Note 1: Place the stand with care not to touch the turn table. -
Page 19: Optical Pick-Up Section
MEX-BT38UW/BT3800U/BT3807U/BT3850U 3-12. OPTICAL PICK-UP SECTION optical pick-up section Note: Be careful not to touch the lens and hologram terminal when removing the optical pick-up section. 3-13. OPTICAL PICK-UP pan tapping screw (M 1.4 × 2.5) leaf spring (sub guide) leaf spring (OP) - Page 20 MEX-BT38UW/BT3800U/BT3807U/BT3850U MEMO...
-
Page 21: Diagrams
MEX-BT38UW/BT3800U/BT3807U/BT3850U SECTION 4 DIAGRAMS 4-1. BLOCK DIAGRAM - AUDIO Section (1/2) - SERVO BOARD AU_LCH CD-L CD MECHANISM AU_RCH R-CH DECK (MG-101Z-188//Q) BT-L (Page 22) MUTING D502 CONTROL SENSOR Q470, 471 D472 BOARD MUTING CONTROL AU_ATT Q493 MUTING CONTROL Q490... -
Page 22: Block Diagram - Audio Section (2/2)
MEX-BT38UW/BT3800U/BT3807U/BT3850U 4-2. BLOCK DIAGRAM - AUDIO Section (2/2) - R-CH ELECTRICAL VOLUME, INPUT SELECT IC401 MUTING MUTING MUTING J901 (2/2) Q480 Q485 Q483 (Page 21) CD-L CD_LCH OUT_FLCH 34 AUDIO OUT FRONT BT-L BT_LCH R-CH J901 (1/2) BUS_LCH OUT_RLCH 32... -
Page 23: Block Diagram - Panel, Power Supply Section
XRESET SYS_RST ACCESSORY XSYS_RST XACC_IN 82 CHECK BU_CHECK Q703 S101 RESET LEVEL SHIFT TEL_ATT 81 Q701 CNJ600 SONY BUS INTERFACE BUS CONTROL IN IC601 DATA_I/O BU_CHECK 10 BU_CHECK DATA_IN 9 UNISO BUS_ON DATA_OUT 8 UNISI CLK_IN 11 UNSCK TH600 BUS_IN 12... - Page 24 MEX-BT38UW/BT3800U/BT3807U/BT3850U THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. • Circuit Boards Location (In addition to this, the necessary note is printed in each block.) SERVO board For Printed Wiring Boards. For Schematic Diagrams. Note: Note: SENSOR board •...
-
Page 25: Printed Wiring Boards - Main Section (1/2)
MEX-BT38UW/BT3800U/BT3807U/BT3850U 4-4. PRINTED WIRING BOARDS - MAIN Section (1/2) - • See page 24 for Circuit Boards Location. • : Uses unleaded solder. MAIN BOARD (COMPONENT SIDE) C318 R488 R478 Q482 D611 C323 Q483 Q484 Q485 Q480 R612 C316 R479... -
Page 26: Printed Wiring Boards - Main Section (2/2)
MEX-BT38UW/BT3800U/BT3807U/BT3850U 4-5. PRINTED WIRING BOARDS - MAIN Section (2/2) - • See page 24 for Circuit Boards Location. • : Uses unleaded solder. J901 J401 BUS AUDIO REAR AUDIO FRONT AUDIO SUB OUT (FRONT VIEW) (MONO) J701 CNJ600 MAIN BOARD... -
Page 27: Schematic Diagram - Main Section (1/4)
MEX-BT38UW/BT3800U/BT3807U/BT3850U 4-6. SCHEMATIC DIAGRAM - MAIN Section (1/4) - • See page 33 for IC Block Diagrams. MAIN BOARD (1/4) TH600 D610 MAZ8180GMLS0 D600 R618 MAZ8062GMLS0 C610 D611 MA2ZD14001S0 R600 D601 D612 MAZ8180GMLS0 MAZ8180GMLS0 R602 Q600 RT1N141C-TP-1 BATTERY CHECK R612... -
Page 28: Schematic Diagram - Main Section (2/4)
MEX-BT38UW/BT3800U/BT3807U/BT3850U 4-7. SCHEMATIC DIAGRAM - MAIN Section (2/4) - • See page 33 for IC Block Diagrams. MAIN BOARD (2/4) Q827 Q820 Q821 RT1P141C-TP-1 RT1P141C-TP-1 RT1P141C-TP-1 Q826 RT1N141C-TP-1 Q820-822 B+ SWITCH Q822 RT1N141C-TP-1 Q826, 827 B+ SWITCH R831 R833 R837 2.2k... -
Page 29: Schematic Diagram - Main Section (3/4)
MEX-BT38UW/BT3800U/BT3807U/BT3850U 4-8. SCHEMATIC DIAGRAM - MAIN Section (3/4) - • See page 33 for IC Block Diagrams. (BT38UW/BT3800U: US, CND/BT3850U) MAIN BOARD (3/4) IC B/D FRONT LCH+ FRONT LCH- IC301 REAR LCH+ CN701 (BT3800U: AEP, UK/BT3807U) POWER AMP, REAR LCH-... -
Page 30: Schematic Diagram - Main Section (4/4)
MEX-BT38UW/BT3800U/BT3807U/BT3850U 4-9. SCHEMATIC DIAGRAM - MAIN Section (4/4) - • See page 24 for Waveforms. • See page 37 for IC Pin Function Description. MAIN (Page 29) BOARD (3/4) MAIN BOARD (4/4) I2C_SIO I2C_SCK C101 C102 R101 R102 FB105 MAIN... -
Page 31: Printed Wiring Boards - Key Section
MEX-BT38UW/BT3800U/BT3807U/BT3850U 4-10. PRINTED WIRING BOARDS - KEY Section - • See page 24 for Circuit Boards Location. • : Uses unleaded solder. LED903, S901 LED907, 932 LED901, 903, 905, 907, 909, (ILLUMINATION) LSW905 – 913 LED910, 912, 914, 916, 919, S901 –... -
Page 32: Schematic Diagram - Key Section
MEX-BT38UW/BT3800U/BT3807U/BT3850U 4-11. SCHEMATIC DIAGRAM - KEY Section - • See page 33 for IC Block Diagrams. KEY BOARD IC B/D CN901 R907 IC902 USB_VBUS R905 R906 S[4] S[21] C912 REMOTE CONTROL SEG4 SEG21 RECEIVER S[3] S[22] USB_GND SEG3 SEG22 IC902... - Page 33 MEX-BT38UW/BT3800U/BT3807U/BT3850U • IC Block Diagrams – MAIN Board – IC1 TEF6617T/V1/S470, 518 IC812 TS5A3159DCKR 6 IN 5 V+ AMRFIN 1 AMOUT2 4 COM AMOUT1 AMRFDEC 2 TUNER AMIFAGC1 FMIN2 3 AMSELIN2 TUNER FMIN1 4 AMSELIN1 GNDRF 5 VCC+8.5V 6 TESTCT...
- Page 34 MEX-BT38UW/BT3800U/BT3807U/BT3850U IC301 TDA8588AJ/N2/R1 PGND2/TAB 1 OUT3– 3 MUTING OUT3+ 5 OUT1– 7 PGND1 MUTING OUT1+ 9 SGND 13 IN2 15 ACGND OUT2+ 17 MUTING PGND3 OUT2– 19 OUT4+ 21 MUTING OUT4– 23 STANDBY/ PGND4 MUTING DIAG 25 PROTECTION/ DIAGNOSTIC IIC-BUS INTERFACE TEMPERATURE &...
- Page 35 MEX-BT38UW/BT3800U/BT3807U/BT3850U IC401 BD3447AFV-E2 I2C BUS LOGIC, FADER FADER FADER FADER FADER EFFECT 180 /0 7 BAND 3 BAND P-EQ (TONE CONTROL) SPECTRUM ANALYZER /LEVEL METER VOLUME/MUTE SPEANA LVL METER LVL METER SPEANA INPUT GAIN INPUT SELECTOR (3 SIGLE-END AND 3 STEREO IS O)
- Page 36 MEX-BT38UW/BT3800U/BT3807U/BT3850U IC851 TPS40200DRG4 UVLO ISNS LOGIC DRIVER E/A AND SS REFFERENCE SOFT-START 700mV OVERCURRENT COMP ENABLE E/A – KEY Board – IC901 LC75829PWH-US-H 59 58 57 56 54 53 52 51 50 49 COMMON DRIVER CCB INTERFACE CLOCK GENERATOR SHIFT REGISTER...
- Page 37 SONY bus data input from the SONY bus interface UNISO SONY bus data output to the SONY bus interface UNISCK SONY bus clock signal output to the SONY bus interface RDS_ON Power on/off control signal output terminal Not used MC_RX...
- Page 38 XACC_IN Accessory power detection signal input terminal “L”: accessory power on XBUS_ON SONY bus on/off control signal output to the SONY bus interface CD_ON CD servo power supply control request input terminal CDM_ON CD mecha power supply control request input terminal...
-
Page 39: Exploded Views
MEX-BT38UW/BT3800U/BT3807U/BT3850U SECTION 5 EXPLODED VIEWS Note: • -XX and -X mean standardized parts, so • Color Indication of Appearance Parts Ex- The components identifi ed by mark 0 they may have some difference from the ample: or dotted line with mark 0 are critical for original one. -
Page 40: Front Panel Section
MEX-BT38UW/BT3800U/BT3807U/BT3850U 5-2. FRONT PANEL SECTION (BT38UW/BT3800U: US, CND) (BT3800U: AEP, UK/BT3807U/BT3850U) not supplied (for FRONT PANEL) not supplied (KEY board) RE901 CN901 not supplied not supplied (JACK board) CN902 LCD901 not supplied not supplied not supplied not supplied Note: Refer to the servicing notes “NOTE FOR REPLACEMENT OF THE USB CONNECTOR (CN902)”... -
Page 41: Cd Mechanism Deck Section (Mg-101Z-188//Q)
MEX-BT38UW/BT3800U/BT3807U/BT3850U 5-3. CD MECHANISM DECK SECTION (MG-101Z-188//Q) not supplied not supplied not supplied not supplied not supplied not supplied not supplied not supplied not supplied not supplied not supplied not supplied not supplied not supplied Ref. No. Part No. Description Remark Ref. -
Page 42: Electrical Parts List
MEX-BT38UW/BT3800U/BT3807U/BT3850U SECTION 6 ANTENNA JACK ELECTRICAL PARTS LIST Note: • Due to standardization, replacements in • RESISTORS When indicating parts by reference num- the parts list may be different from the All resistors are in ohms. ber, please include the board name. - Page 43 MEX-BT38UW/BT3800U/BT3807U/BT3850U MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < TRANSISTOR > R990 1-216-818-11 METAL CHIP 1/10W R991 1-216-819-11 METAL CHIP 1/10W Q901 8-729-027-44 TRANSISTOR DTC114TKA-T146 R998 1-216-864-11 SHORT CHIP Q907 8-729-027-44 TRANSISTOR DTC114TKA-T146 R999...
- Page 44 MEX-BT38UW/BT3800U/BT3807U/BT3850U MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C110 1-162-964-11 CERAMIC CHIP 0.001uF C482 1-126-964-11 ELECT 10uF C111 1-127-760-11 CERAMIC CHIP 4.7uF 6.3V C483 1-126-964-11 ELECT 10uF C112 1-126-934-11 ELECT 220uF C484 1-126-964-11 ELECT...
- Page 45 MEX-BT38UW/BT3800U/BT3807U/BT3850U MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C854 1-107-826-11 CERAMIC CHIP 0.1uF D702 6-501-782-01 DIODE MAZ8180GMLS0 C855 1-164-315-11 CERAMIC CHIP 470PF D703 6-501-782-01 DIODE MAZ8180GMLS0 C856 1-164-315-11 CERAMIC CHIP 470PF D704 6-501-782-01 DIODE MAZ8180GMLS0...
- Page 46 MEX-BT38UW/BT3800U/BT3807U/BT3850U MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-410-501-61 INDUCTOR 2.2uH 1-216-864-11 SHORT CHIP 1-457-817-11 COIL (FM MIX) (BT3800U: AEP, UK/BT3807U/BT3850U: EA) 1-481-285-51 INDUCTOR 560uH 1-216-864-11 SHORT CHIP 1-481-285-51 INDUCTOR 560uH 1-216-864-11 SHORT CHIP...
- Page 47 MEX-BT38UW/BT3800U/BT3807U/BT3850U MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R501 1-216-845-11 METAL CHIP 100K 1/10W R560 1-216-829-11 METAL CHIP 4.7K 1/10W (BT3807U) R561 1-216-849-11 METAL CHIP 220K 1/10W R502 1-216-845-11 METAL CHIP 100K 1/10W R565...
- Page 48 MEX-BT38UW/BT3800U/BT3807U/BT3850U MAIN SENSOR SERVO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R830 1-216-864-11 SHORT CHIP SENSOR BOARD R831 1-216-825-11 METAL CHIP 2.2K 1/10W ************** R832 1-216-825-11 METAL CHIP 2.2K 1/10W ************************************************************ R833 1-216-829-11 METAL CHIP 4.7K...
- Page 49 MEX-BT38UW/BT3800U/BT3807U/BT3850U Ref. No. Part No. Description Remark 4-158-430-41 MANUAL, INSTRUCTION, INSTALL (RUSSIAN, UKRAINIAN) (BT3807U) 4-158-430-51 MANUAL, INSTRUCTION, INSTALL (ENGLISH, SPANISH) (BT3850U: E) 4-158-430-61 MANUAL, INSTRUCTION, INSTALL (ENGLISH, ARABIC, PERSIAN) (BT3850U: EA) ************************************************************* KEY (FRAME) FITTING FRAME ASSY PARTS FOR INSTALLATION AND CONNECTIONS...
- Page 50 MEX-BT38UW/BT3800U/BT3807U/BT3850U REVISION HISTORY Checking the version allows you to jump to the revised page. Also, clicking the version at the top of the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2009.11...