Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Haier HLF11P
Summary of Contents for Haier HLF11P
- Page 1 HLF11P...
- Page 2 WARNING...
-
Page 5: Table Of Contents
Unpacking Your Dryer ... 16 Exhaust System Connections ... 17 Requirements and Instructions... 17 Materials ... 18 Location of Your Dryer ... 20 Installation in Mobile Home ... 21 Electrical Connections ... 22 Requirements and Instructions ..22 3-Wire Cord Connections... 23 4-Wire Cord Connections... -
Page 6: Operating Instructions
Temp Towels/Cotton Power On/Off Button: (1) Press the button once to operate the dryer. Press the button once again to turn the dryer "OFF". Start/Pause Button: (2) Press this button once to start the dry process. Press this button once again to pause the activity during the dry cycle. - Page 7 Cycle Signal Button: (4) Used to select buzzing volume or turn off the buzzer. Timed/Cycles Button: (5) "Timed/Cycles" button will let you select your desired dry mode. Auto Dry: automatically set "Dryness Level", "Temp", "Cycle Signal", "Wrinkle Care" buttons status according to clothes loaded. Timed Dry: you can set status of "Temp", "Cycle Signal"...
-
Page 8: Preparations Before Drying
Dark and light colored clothes shall be separately dried. Fabrics prone to falling lint and those prone to adhering lint shall be separately dried. Clothes prone to falling lint shall be turned inside out before putting into the dryer. Make sure buttons and ornaments on the clothes are high temperature resistant and won't damage drum surface. -
Page 9: Load Clothes Into Dryer
Towels/Cotton 1. Press "Power On/Off" button to power on Turn on the power switch, the computer board beeps once and the dryer transfers from off status to the initial operating status (Normal program); If no "Start/Pause" button is pressed in 5 min after powering on, it automatically cuts off power and returns to off status;... - Page 10 Various button initial status for "Normal program" Softer Cycle Signal Wrinkle Care Normal Cycles Indicate current program remaining time Nixie display Temp High More Dry Dryness Level Auto-program Timed/Cycles 2. Press "Cycles" button to select a suitable full automatic cycle The Normal program will be automatically selected after powering on.
- Page 11 3. Press "Dryness Level" button to select a suitable drying time After powering on, the clothes dryer automatically sets dryness at "More Dr y", which means the normal drying time. If other drying time is desired, press "Dryness Level" button to select a shorter time.
-
Page 12: Timed Dry Cycle
Timed Dry cycle More Dry Cool down High Cycle completed Customer Medium Extend trumble Normal Less Dry Air Only(No Heat) Dryness Heavy Duty Level Temp Towels/Cotton 1. Press "Power On/Off" button to power on 2. Press "Timed/Cycles" button and select "Timed Dry" cycle After powering on, press "Timed/Cycle"... -
Page 13: Other Features
All dryers come with a lint filter that needs to be cleaned before or after every use (read Care and CleaningGuide Section). Leveling Legs: Your dryer has four leveling legs which are located in the front and rear corners of your dryer. After installingyour dryer in its final position, you can level your dryer. - Page 14 All dryers come with a lint filter that needs to be cleaned before or after every use (read Care and CleaningGuide Section). Leveling Legs: Your dryer has four leveling legs which are located in the front and rear corners of your dryer. After installingyour dryer in its final position, you can level your dryer.
-
Page 22: Location Of Your Dryer
Location of Your Dryer Do Not Install Your Dryer: In an area exposed to dripping water or outside weather conditions. In an area where it will come in contact with curtains, thick carpet, or anything that will obstruct the flow of combustion and ventilation air. -
Page 23: Installation In Mobile Home
Metal ducting must be 4 inches (10.16 cm) in diameter with no obstructions. Rigid metal duct is preferred. If dryer is exhausted through the floor and area beneath the mobile home is enclosed, the exhaust system must terminate outside the enclosure with the termination securely fastened to the mobile home structure. - Page 25 Circuit MOTOR THERMAL LIMITER DOOR Computer Program SWITCH Controller HIGH LIMIT THERMOSTAT RELAY HEATER CONTROL THERMOSTAT...
- Page 26 Circuit MOTOR THERMAL LIMITER DOOR Computer Program SWITCH Controller HIGH LIMIT THERMOSTAT RELAY HEATER CONTROL THERMOSTAT Circuit...
-
Page 28: Specification
Model Rated voltage , frequency Rated dry capacity Rated dry power Weight (about) Dimension HLF11P 120V/240V~ 60Hz 10 kg 5000W 55 kg L712mm W686mm H1115mm...