Taramps Tarsafe TW20 G4 Manual
  1. Manuals
  2. Brands
  3. Taramps Manuals
  4. Security System
  5. Tarsafe TW20 G4
  6. Manual

Taramps Tarsafe TW20 G4 Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
TW20
MANUAL
AUTOMOTIVE ALARM

Advertisement

Table of Contents
loading

Related Manuals for Taramps Tarsafe TW20 G4

Summary of Contents for Taramps Tarsafe TW20 G4

  • Page 1 TW20 MANUAL AUTOMOTIVE ALARM...

  • Page 2: Before Starting

    1) Before Starting: ATTENTION: We recommend the complete reading of this manual before proceeding with the installation of this product. This product is intended to make it difficult or inhibit the theft / robbery of the vehicle, or • objects in it. Before contacting T ARAMPS technical support, make sure you read this manual, it contains all •...

  • Page 3: Remote Controls

    Controls Functions (Manufactured from June 2019) - Anti Jammer function. EXCLUSIVE IN THE G4 TARAMPS LINE. Jammer is when there is another control transmitting near the alarm center,making it impossible to turn the alarm on or off by the registered control.

  • Page 4: Remote Control Functions

    5) Remote Control Functions: FUNCTION CONTROL ACTION ALARM RESPONSE 1 Flash on Turn Signals+ 1 Siren beep3 1 - Turn alarm on Press Beeps indicate Open Door Item 9.1 2 flashes on turn signals + 2 siren beeps Note: 4 flashes on the turn signals+ 4 beeps, 2 - Turn Alarm off...
  • Page 5 6) Programming by Master Key Configure Select Function With the door open, turn the ignition on and hold the START master pressed until the desired function beeps. The alarm will beep with the current setting, to change, press Example: the master the number of times of the desired setting. DOOR OPEN IGNITION MASTER...
  • Page 6 7) Lock Function by Presence/ Distancing TR2-P Control Required Operation: With the ignition on and doors closed, pulling the TR2-P control away from the vehicle automatically activates the distancing lock. After the programmed time (Beep 9 of the configuration by the master), the ultrasound LED starts flashing the audio will be turned off, the siren and turn signals will go off, ther 10 seconds, the engine will start failing until it is definitively blocked.
  • Page 7 7.2) Test the automatic transmission range: Operation: It is used to test the automatic transmission range of the Presence function on the TR2-P control.With the automatic transmission of the presence function activated in the control and the function activated in the alarm central, hold the off and auxiliary keys pressed until the LED goes out. After releasing the keys, the LED will flash every 2 seconds, on each flash,the alarm will respond with a BEEP, informing that it has received the transmission.
  • Page 8 Installation Scheme: Fix on the vehicle windshield, 10cm below the roof Left Side Receiver Right Side Transmitter ATTENTION: The TW20 G4 LINE has a new Ultrasound transmitter. In case the old alarm central is replaced by G4, the transmitter sensor (right side sensor, without LED) must also be replaced by the new one.

  • Page 9: Alarm Functions

    Attention: Function canceled from factory, need to be enabled by Beep 8. In G4 alarms it is possible to simultaneously enable the Beep 8 Secret Button Lock and the Beep 7 Presence Function. Set Time for Locking, 1, 2 or 3 minutes - With the door open, turn the ignition on.

  • Page 10: Relay Connections

    10) Relay Connections The lock, unlock, auxiliary and audio equipment outputs can handle a maximum of 200mA. If it is necessary to install equipment with a consumption that is higher than 200mA, relays must be used. Transform NEGATIVE alarm signal Transform POSITIVE alarm signal (AUDIO) Transform NEGATIVE alarm signal (200mA) into POSITIVE +12V...
  • Page 11 Window Activation Setup (continuation) Set Signal for window/Electric Lock activation - With the door open, turn the ignition on. Configure - Hold a master pressed until beep 11. Select the Beep 11 function - The alarm will respond informing: START 1 Beep = Universal 2 Beeps = VW G5 1X = Universal...

  • Page 12: Led Functions

    12) G2 Ultrasound Sensors Attach the sensors to the vehicle's windshield, 10 cm below the roof. Ultrasound sensors come with digital sensitivity adjustment. Change the default setting only if necessary. The table follows below: Sensor Sensitivity Click Alarm Response 1 Once +20% 1 Beep 2 Twice...
  • Page 13 Auxiliary Output 2 Setup- brown wire Programming by Master - With the door open, turn the ignition on. - Hold the master pressed until beep 13. Configure Select the Beep 13 function - The alarm responds by informing the current setting: 1 Beep = Reads negative switch START 2 Beeps = Lê...

  • Page 14: Warranty Term

    Taramps Electronics - Rua: Abílio Daguano, nº 274 - ZIP19.180-000 Fones: +55(18) 3266-4050 / 99749-3391 E-mail: service@taramps.com.br Taramps reserves the right to change the contents of this manual without prior notice or obligation to apply the modifications to previously produced units.
  • Page 15 Fabricado por / Manufactured by: TARAMPS ELECTRONICS LTDA CNPJ / TAX ID: 11.273.485/0001-03 R. João Silvério, 121• Res. Manoel Martins Alfredo Marcondes - SP Indústria Brasileira - Made in Brazil...

Table of Contents