Related Manuals for Avigilon NVR5-STD-2NDCPU
Summary of Contents for Avigilon NVR5-STD-2NDCPU
- Page 1 Avigilon NVR5 Standard 2 CPU Kit Installation Guide Installation Guide NVR5-STD-2NDCPU NVR5 STD 16TB-64TB...
- Page 2 © 2022, Avigilon Corporation. All rights reserved. AVIGILON, the AVIGILON logo, AVIGILON are trademarks of Avigilon Corporation. Intel is a trademark of Intel Corporation or its subsidiaries in the U.S. and/or other countries. Other names or logos mentioned herein may be the trademarks of their respective owners. The absence of the symbols ™...
-
Page 3: Table Of Contents
Table of Contents Introduction Confirm Package Contents Recommended Tools Installing the NVR5 2nd CPU Kit Opening the Cover Installing the CPU Installing Additional RAM Reattaching the Cover Confirming the Installation For More Information... -
Page 4: Introduction
Introduction Avigilon provides an optional 2 CPU kit for the NVR5 Standard. These kits provide all the components needed to add CPU redundancy to an NVR. Part Number Description NVR5-STD-2NDCPU NVR5 Standard 2 CPU Kit Important: A second power supply (NVR5-PSU-800W) is required in order to enable the 2 CPU Kit... -
Page 5: Installing The Nvr5 2Nd Cpu Kit
Installing the NVR5 2 CPU Kit Note: If the NVR5 is an operating part of your security system, be aware that it must be shut down to complete this procedure. Before starting to install the kit: 1. Turn off the NVR5, including all attached peripherals. Press the power button on the front panel, and wait for the light to stop blinking to indicate shutdown is complete. -
Page 6: Opening The Cover
Opening the Cover 1. At the top of the NVR5, unlock the latch release then lift and rotate the latch towards the back of the unit. The cover slides back and is released from the body. Tip: Use a Phillips #2 screwdriver to remove the shipping screws before unlatching the cover if you are removing the cover of an NVR5 for the first time. - Page 7 3. View the interior of the NVR5 and identify the locations where the components of the kit will be installed. The view below shows the details of an NVR5 with all of the covers and cards removed, and important components labeled with numbers. The components affected by the NVR5 Standard 2 CPU Kit are: 3—Memory module...
-
Page 8: Installing The Cpu
Installing the CPU You need the processor bracket, processor (CPU), and heatsink provided in the kit to complete this procedure. With the NVR5 open and the protective cover removed: 1. Unpack the CPU. 2. Place the processor in the processor tray. Note: Ensure that the pin 1 indicator on the processor tray is aligned with the pin 1 indicator on the processor. - Page 9 5. Unpack the heat sink and remove the protective film from the base of the heat sink. Be careful not to touch the thermal paste that is pre-applied to the bottom of the heat sink. 6. Place the heat sink on the processor and press the heat sink until the carrier locks onto the heat sink at all the four corners.
- Page 10 7. Locate the 2 processor socket and pull off the CPU dust cover over the socket. 8. Align the pin 1 indicator of the processor heat sink module (PHM) to the system board and then place the processor heat sink module (PHM) on the processor socket. Important: Ensure that the processor and heat sink module is held parallel to the system board to prevent damaging the components.
- Page 11 9. Set the anti-tilt wires to the locked position (outward position), and then use the star-shaped screwdriver #T30 to tighten the screws on the heat sink in the following order: a. In a random order, tighten the first nut three turns. b.
-
Page 12: Installing Additional Ram
Installing Additional RAM Important: To prevent damage to the DIMM or memory module socket during installation: Do not bend or flex the DIMM. Handle each DIMM only by the edges to ensure that you don't touch the middle of the memory module or the metallic contacts. -
Page 13: Reattaching The Cover
Reattaching the Cover When all the components of the kit have been installed: 1. Reinstall the top of the cooling shroud: a. Align the slot on the air shroud with the standoff in the system. b. Lower the air shroud into the system until it is firmly seated. 2. -
Page 14: Confirming The Installation
The number of connected cameras should be the same as before the NVR5 was upgraded, and the analytics load should be about half of what it was prior to the upgrade. Limited Warranty Avigilon warranty terms for this product are provided at avigilon.com/warranty. Confirming the Installation... -
Page 15: For More Information
For More Information For additional product documentation and software and firmware upgrades, visit support.avigilon.com. Technical Support Contact Avigilon Technical Support at support.avigilon.com/s/contactsupport. For More Information...
Need help?
Do you have a question about the NVR5-STD-2NDCPU and is the answer not in the manual?
Questions and answers