Advertisement
Operation
MODE
FAN
SWING
TEMP
HEALTH
3
CLOCK
SET
2
SET
TIMER
SLEEP
HEAT
FILTER RESET
5
ON
OFF
4
RESET
AM
PM
ON/OFF
The function of code A:TIMER ON/OFF
(1)After unit start, select your desired operation mode
Operation mode will be displayed on LCD.
Power indicator lights up.
(2) Press TIMER button to change TIMER mode
Every time the button is pressed, display changes as
follows:
ON
blank
ON
OFF
OFF
ON
Select
.
OFF
(3)Time setting for TIMER ON
Press TIME button.
Every time the button is pressed, time increases 10min.
If button is kept depressed, time will change quickly.
Every time the button is pressed, time decreases 10min.
If button is kept depressed, time will change quickly.
Time will be shown on LCD.
It can be adjusted within 24hours.
AM refers to morning and PM to afternoon.
To cancel TIMER mode
Just press TIMER button several times until TIMER mode disappears.
According to the Time setting sequence of TIMER ON or TIMER OFF, either Start-Stop or Stop-Start
can be achieved.
A
TEMP
ON
6
1
OFF
SWING
FAN
MODE
SLEEP
HEALTH
FRESH
3
CLOCK
SET
1
2
6
TIMER
HIGH/SO
5
4
FILTER
HEAT
LIGHT
LOCK
RESET
CODE
(4) Time confirming for TIMER
After time setting, press TIMER button to
confirm."ON" stops blinking, While "OFF"
starts blinking.
Time displayed: Unit starts at Xhour X min.
(5)Time setting for TIMER OFF
Follow the same procedures in "Time setting
for TIMER ON".
(6)Time confirming for TIMER OFF
After time setting, press SET button to confirm
"OFF" stops flashing.
Time displayed: Unit stops at X hour X min.
7
Parts and Functions
16.FRESH Button
Used to set fresh mode, the unit will draw in fresh air.
17.SLEEP Button(In function of code A)
(The clock must be corrected before setting sleep function)
Used to set sleep mode.
18.FAN Button
Used to select fan speed:LOW,MID,HIGH,AUTO.
19.TIMER OFF Display
20.TIMER Display
21.FILTER Display
When the filter need be cleaned, the sign will
appear automatically.
22.TEMPERATURE Display
23.AUTO SWING Display
24.HIGN/SO Run Display
25.Code A display
26.SIGNAL SENDING Display
27.Code B display
28.Fresh Display
29.Auxiliary ELECTRICAL HEATING Display
30.HEALTH Display
Displays when healthy run function is set.
31.Operation MODE Display
32.SLEEP State Display( In function of code A)
33.BATTERY Energy Display
Notify the user when it is time to change the batteries.
34.LOCK State Display
35.FAN SPEED Display
The function of code A
The function of code B
A
A
U
U
T
T
O
O
LOW
MID
HIGH
AUTO
LOW
MID
HIGH
AUTO
36.TIMER ON Display
37.HEAT Button
Used to select Auxiliary electric heater.
Remote Controller Operation
When in use, direct signal transmission head to
the receiver placed on the indoor unit
Clock Set
When unit is started for the first time and after replacing batteries in remote controller, clock should
be adjusted as follows:
1.Press CLOCK button, clock indication of " AM " or " PM " flashes.
2.Press
or
to set correct time. Each press will increase or decrease 1 min. If the button is kept
pressed, time will increase or decrease quickly.
3.After time setting is confirmed, press "SET" : AM or PM stop flashing, while clock starts working.
Note:AM means morning and PM means afternoon.
The distance between the remote controller and the receiver
should be max 7m and there should be no obstacle between them.
Do not throw the remote controller; prevent it from being damaged.
When operating the remote controller in an area where
electronically controlled lights are installed or wireless handsets
are used, please move closer to the indoor unit as the function
of the remote controller might be affected by signals emitted by
the above mentioned equipments.
Battery loading
Battery loading
Batteries are fitted as follows:
Remove the battery compartment lid
Slightly press and disengage the battery compartment lid marked
"
"
with
and then hold the remote controller by the upper
section and then remove the battery compartment lid by pressing
in the direction of the arrow as shown in the figure above.
Loading the battery
Ensure that batteries are correctly placed in the compartment
as required for positive and negative terminals.
Replacing the battery compartment lid
The battery compartment lid is reinstalled in the reverse
sequence.
Display review
Press the button to see if batteries are properly fitted. If no
display appears, refit the batteries.
Confirmation indicator
If no indication is displayed after press ON/OFF button,
reload the batteries.
Caution:
If the remote controller does not operate as designed after
fitting new batteries of the same
type, press the Reset button (marked ) with a pointed article.
Note:
It is recommended that the batteries be removed from the
compartment if the remote controller is not used for an extended
period.
The remote controller is programmed for automatic test of
operation mode after the batteries are replaced. When the test
is conducted, all icons will appear on the screen and then
disappear if the batteries are properly fitted.
When the display become weak, this display no power
in the battery, please change the battery.
MODE
SLEEP
HEALTH
FRESH
CLOCK
SET
1
TIMER
2
HIGH/SO
FILTER
HEAT
RESET
CODE
LIGHT
LOCK
4
3
Advertisement
