Advertisement
Parts and Functions
Left picture is a wired remote controller,
which can be used on Series wired control
units ,The remote controller can be purchased
B
A
extrally.
Wired remote Controller using method:
1.Use one wired remote controller. See fig (1)
A
U
T
O
2.Also can buy a remote controller extrally, realize
OFF
M
D
fig(1)
wired remote control + remote control dual control modes.
3.When the remote controller can be used on series wired
TEMP
ON
remote controller units ,than please press the botton
OFF
SWING
FAN
"CODE"to choose the program of code "A"
4.Series wired remote control units have power failure
MODE
SLEEP
HEALTH
FRESH
compensation.
CLOCK
SET
TIMER
HIGH/SO
FILTER
HEAT
FAN
MODE
RESET
CODE
LIGHT
LOCK
AUTO
TEMP
HEALTH
CLOCK
SET
TIMER
*
ROOM
ON
OFF
HEAT
FILTER RESET
ON/OFF
Remote controlller
Wire remote controlller
Remote controlller is an accessory, to be ordered extrally
The right figure is a remote controller, which can be used on
series remote control units and the matching remote control receiver
1.Remote control receiver using method :
Use remote controller control the
remote control window of the remote
control receiver.
2.Series remote
controller units
please press the
botton "CODE"to choose
the program of code "B"
3.Series remote control units
have not power failure compensation.
MODE
FAN
AUTO
TEMP
CLOCK
SET
TIMER
*
ROOM
ON
OFF
HEAT
FILTER RESET
ON/OFF
B
SWING
A
U
SET
T
O
OFF
SLEEP
M
D
RESET
TEMP
fig(2)
ON
OFF
SWING
MODE
SLEEP
HEALTH
FRESH
CLOCK
SET
TIMER
HIGH/SO
FILTER
HEAT
LIGHT
LOCK
RESET
CODE
Remote receiver
Remote controlller
1
Health Function and Installating the Reciever
About health function
SWING
HEALTH
SET
SLEEP
MODE
RESET
CLOCK
SET
TIMER
OFF
HEAT
AM
AM
ON/OFF
On the "Health" mode, if you want
to setting timing open mode, should
close the health first: On the timing
open mode, please don't use health
A
function.
Installation of receive display
Because of the temperature sensitive device, do not install the receive display at straight sunlight place,
either in front of air outlet grill, for it is effected greatly from cool air and heat air, the receive display is
at least 20mm distance to the air outlet grill.
Since there is light sensitive device which receives wireless remote signal, so do not installed behind the
window curtain or other obstacles, in order not to obstruct the signal.
Must fix the remote control wire far from strong electricity (such as the wiring of electric light, air cond-
itioner, etc.) and weak electricity (such as the wiring of telephone, interphone, etc.).
FAN
1.Fix the receive display with screws
on the selected place
Connecting wiring method of receiver :
Refer the indoor unit wiring diagram .
Safety cautions see the electrical wiring part .
1 .Emergency switch
2 .Running lamp: When the compressor working, this lamp bright.
3 .Timing lamp: When the unit been setting Timing running, this lamp bright.
4 .Power lamp: After open the unit, this lamp bright when the unite enter
health running, the lamp change from orange to blue lamp.
5 .Indoor temp. sensor: Test the room temperature.
1.How to use the health function (only for units with this function)
After set the right function mode, press health button,
remote controller or wire controller displays " ",oxygen pump
or negative ion generator starts up to apply oxygen or negative
A
U
T
O
FAN
SWING
OFF
ion to indoor unit. Press the button again,the sign " " disapp-
TEMP
HEALTH
TEMP
eared and negative ion generator stops working. After all health
ON
OFF
SET
SWING
FAN
function of the indoor unit being fully canceled, oxygen pump
MODE
SLEEP
SLEEP
stopped.
HEALTH
FRESH
FILTER RESET
RESET
CLOCK
SET
TIMER
HIGH/SO
CAUTION:
FILTER
HEAT
When the temperature of the outdoor unit is lower than 4
LIGHT
LOCK
RESET
CODE
oxygen pump is automatically stopped, if press health button
just then, oxygen pump could not start up. But if the air condi-
tioner has the negative ion function simultaneous,when press
the Health button, negative ion function could still be operated.
When the temperature of the outdoor unit is higher than 6
oxygen pump could automatically resume to oxygen-make
function.
2.Place the panel onto the fixed frame, pay attention
that the four claws must be placed into the
corresponding four poles on the frame
10
C
,
C
,
5
2
4
3
1
Advertisement
