DeWalt XR Li-Ion DCS365 Original Instructions Manual page 44

EnGLIsH
Storage Recommendations
1. The best storage place is one that is cool and dry away from direct
sunlight and excess heat or cold. For optimum battery performance and
life, store battery packs at room temperature when not in use.
2. For long storage, it is recommended to store a fully charged battery
pack in a cool, dry place out of the charger for optimal results.
nOTE: Battery packs should not be stored completely depleted of charge.
The battery pack will need to be recharged before use.
Labels on Charger and Battery Pack
In addition to the pictographs used in this manual, the labels on the charger
and the battery pack may show the following pictographs:
Read instruction manual before use.
See Technical Data for charging time.
Do not probe with conductive objects.
Do not charge damaged battery packs.
Do not expose to water.
Have defective cords replaced immediately.
Charge only between 4 ˚C and 40 ˚C.
Only for indoor use.
Discard the battery pack with due care for the environment.
Charge D WALT battery packs only with designated D
e
chargers. Charging battery packs other than the designated
D WALT batteries with a D
e
burst or lead to other dangerous situations.
Do not incinerate the battery pack.
USE (without transport cap). Example: Wh rating indicates 108
Wh (1 battery with 108 Wh).
TRANSPORT (with built-in transport cap). Example: Wh rating
indicates 3 x 36 Wh (3 batteries of 36 Wh).
Battery Type
The DCS365operates on a 18 volt battery pack.
These battery packs may be used: DCB141, DCB142, DCB143, DCB144,
DCB145, DCB181, DCB182, DCB183, DCB183B, DCB184, DCB184B, DCB185.
Refer to Technical Data for more information.
Package Contents
The package contains:
1 Mitre saw
1 Blade wrench
1 Saw blade
1 Side handle package
1 Dustbag
1 Material clamp
42
WALT
e
WALT charger may make them
e
1 Li-Ion battery pack (C1, D1, L1, M1, P1, S1, T1, X1 models)
2 Li-Ion battery packs (C2, D2, L2, M2, P2, S2, T2, X2 models)
3 Li-Ion battery packs (C3, D3, L3, M3, P3, S3, T3, X3 models)
1 Instruction manual
nOTE: Battery packs, chargers and kitboxes are not included with N models.
Battery packs and chargers are not included with NT models. B models
include Bluetooth® battery packs.
• Check for damage to the tool, parts or accessories which may have
occurred during transport.
• Take the time to thoroughly read and understand this manual prior
to operation.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
Keep hands away from blade.
Visible radiation. Do not stare into light.
Date Code Position (Fig. A)
The date code 24 , which also includes the year of manufacture, is printed
into the housing.
Example:
2018 XX XX
Year of Manufacture
Description (Fig. A)

WARNING: Never modify the power tool or any part of it. Damage or
personal injury could result.
Trigger switch
1
Operating handle
2
Mounting holes
3
Lower guard
4
Mitre lock knob
5
Kerf plate
6
Mitre arm
7
Mitre scale
8
Mitre scale screws
9
Side handles
10
Fence
11
Bevel lock knob
12
Rails
13
Intended Use
Your D WALT DCS365 cordless sliding compound mitre saw has been
e
designed for professional wood cutting applications. It performs the
sawing operations of cross-cutting, bevelling and mitring easily, accurately
and safely.
This unit is designed for use with a nominal blade diameter 184 mm carbide
tip blade.
nEVER cUT METALs or light alloy, especially magnesium.
Dust port
14
Lifting handle
15
Battery pack
16
XPS™ worklight momentary
17
switch
Lock off lever
18
Rail adjustment screw
19
Rail lock knob
20
Clamp hole
21
Blade wrench
22
Lock down pin
23
Date code
24
Bevel override
25