Bosch D-tect 150 Original Instructions Manual page 19

Changing the display mode
Note: It is possible to change the display mode in all operat-
ing modes.
Press and hold the select button (10) or (12) to switch from
the default display screen to Metric rule mode.
N
? 8.8 cm
S
20.1 cm
18 19 20
cm 10 cm 20cm
Prev. Concrete deep
In the example, Metric rule mode shows the same situation
as in figure D: Three iron rods, equally spaced. In Metric rule
mode, the distance between the centres of detected objects
can be determined.
The distance travelled along the measuring path from the
starting point is displayed below the permitted drilling depth
indicator (l); in the example, this is 20.1 cm.
The three detected objects are displayed as rectangles on
the small rule above the operating mode indicator (h).
Note: Both the permitted drilling depth indicator (l) and the
material property indicator (m) relate to the object shown in
black on the sensor screen.
Briefly press the select button (10) or (12) to return to the
default display screen.
Note: Only the display is changed, not the measuring mode!
Settings menu
To open the Settings menu, press the setup button (14).
To exit the menu, press the start button (11). The settings
that are currently selected are applied. The default display
screen for the measuring process is activated.
Navigating in the menu
To scroll down, press the setup button (14).
Press the select buttons (10) and (12) to select the values:
– Pressing the select button (10) selects the right-hand/
next value.
– Pressing the select button (12) selects the left-hand/pre-
vious value.
<Language>
In the <Language> menu, you can change the language of
the menu navigation. The default setting is <English>.
<Cut-off time>
In the <Cut-off time> menu, you can set the time before the
measuring tool switches off automatically when no measure-
ment is taken and no settings are adjusted. The default set-
ting is <5 min>.
Bosch Power Tools
<Display illum.>
In the <Display illum.> menu, you can set the time for which
the display (16) remains illuminated. The default setting is
<30 sec>.
<Brightness>
In the <Brightness> menu, you can set the brightness of the
display. The default setting is <Max>.
<Tone signal>
In the <Tone signal> menu, you can set when the measuring
tool should emit an audio signal, providing you have not
switched off the signal by pressing the audio signal but-
ton (13).
21 22 23
– The default setting is <Wallobjects>: An audio signal
30cm 40
Next
– With the <Live wire> setting, an audio signal sounds
– With the <Keyclick> setting, an audio signal only sounds
<Defaultmode>
In the <Defaultmode> menu, you can set the operating
mode that will be selected by default when the measuring
tool is switched on. The default setting is <Universal
mode>.
Advanced settings menu
To open the Advanced settings menu, press the setup but-
ton (14) and the on/off button (15) simultaneously while the
measuring tool is switched off.
To exit the menu, press the start button (11). The default
display screen for the measuring process is activated and
the settings are applied.
Navigating in the menu
To scroll down, press the setup button (14).
Press the select buttons (10) and (12) to select the values:
– Pressing the select button (10) selects the right-hand/
– Pressing the select button (12) selects the left-hand/pre-
<Device Info>
The <Device Info> menu contains information about the
measuring tool, e.g. the <Operation Time>.
In the <Restore Settings> menu, you can restore the fact-
ory settings.
Examples of measuring results
Note: In the following examples, the audio signal on the
measuring tool is switched on.
sounds every time a button is pressed and whenever an
object is located in the wall within the sensor range. In ad-
dition, a short repeated warning signal is given for live
wires.
every time a button is pressed and the warning signal is
given for live cables (short, repeated) whenever the
measuring tool displays a power cable.
when a button is pressed.
next value.
vious value.
1 609 92A 4G0 | (22.08.2018)
English | 19