Autofeed; Lubrication; Batteries; Battery Disposal - RIDGID K-39 Series Operator's Manual

K-39/K-39B Drain Cleaning Machine

Autofeed

A drop of grease to the following areas once a month will
extend the life of the autofeed unit and keep it well main-
tained:
A. Top of large Top Adjustment Screw
B. Threads on bottom of Top Adjustment Screw
C. Outside diameter of Top Roller Holder housing
The autofeed will accumulate dirt, grease and debris
over time. Periodically remove the autofeed unit and
clean with cleaning solvent and a firm brush.
Once a week a light grease should also be applied to the
autofeed roller bearing surface. This will extend the life of
the bearings and keep them free to operate properly.

Lubrication

Disassembly of the K-39/K-39B Drain Cleaner monthly for
cleaning and lubrication:
1. Disassemble unit:
A. Unscrew nose piece. Thread is a normal right hand
thread. If necessary, use adjustable pliers to re-
move.
B. Pull off hand grip assembly.
C. Remove springs. The two clamp springs attach
to canister front half in a manner similar to a peg-
board hook.
2. Thoroughly clean all parts. If required, use emery
cloth to remove rust and/or scale from inside of sleeve.
3. Coat springs and inside sleeve with good quality
bearing grease and reassemble.

Batteries

1. Be alert for battery packs that are nearing their end of
life. Battery packs typically last from 250 to 500
charges. If you notice decreased tool performance or
significantly shorter running time between charges
then it is time to replace the battery pack. Failure to do
so can cause the tool to operate improperly or damage
the charger.
2. Long term battery storage should be in the discharged
state. Battery packs last longer and re-charge better
when they are stored discharged. Remember to fully
re-charge battery packs before using after prolonged
storage.

Battery Disposal

Do not attempt to disassemble the bat-
WARNING
tery or remove any component projecting from the
battery terminals. Fire or injury may result. Prior to dis-
12
posal, protect exposed terminals with heavy insulating
tape to prevent shorting.

Nickel-cadmium Batteries

If equipped with a nickel-cadmium battery, the battery
must be collected, recycled or disposed of in an environ-
mentally sound manner.
Please call 1-800-8 BATTERY for information on Ni-Cd
battery recycling and disposal bans/restrictions in your
area.

Nickel-metal Hydride Batteries

If equipped with a nickel-metal hydride battery, the battery
can be disposed of in a municipal solid waste stream.

Accessories

Only the following RIDGID products have been designed to
function with the K-39/K-39B Drain Cleaners. Other ac-
cessories suitable for use with other tools may become
hazardous when used on the K-39/K-39B. To prevent se-
rious injury, use only the accessories listed below.
Cables
Catalog
No.
62225
56782
89400
56792 C-131IC
62235
56787
89405
56797 C-23IC
62245
62250
62260
96037
50647
50652
50657
Ridge Tool Company
Model
No. Description
C-1 25' (7,62m) w/Bulb Auger
C-1IC 5 / " x 25' (7,62m) Inner Core
16
w/Bulb Auger
C-21 50' (10,67m) w/Bulb Auger
35' (10,67m) w/Bulb Auger
C-2 25' (7,62m) w/Drop Head Auger
C-2IC 25' (7,62m) Inner Core
w/Drop Head Auger
C-22 50' (15,24m) w/Drop Head Auger
35' (10,67m) w/Drop Head Auger
C-4 25' (7,62m) w/Male Coupling
C-5 35' (10,67m) w/Bulb Auger
C-6 35' (10,67m) w/Male Coupling
C-6IC 35' (10,67m) Inner Core
w/Male Coupling
S-1 15' with Bulb Auger
S-2 25' with Bulb Auger
S-3 35' with Bulb Auger