1.1 What you can do with G7 Dataseed 1.2 Electrical connections 1.3 How to install the GNSS receiver 1.3.1 How to connect the GNSS receiver to G7 Dataseed 1.3.2 Receiver position - orientation 1.3.3 Receiver position - Transverse axis 1.3.3.1 Seeder / planter installation 1.3.3.2 Weeder installation...
-Export the recorded tracks with high density of dots. 1.2 Electrical connections G7 Dataseed is equipped with a bracket and harness with connectors for easy and safe installation on the vehicle. The wiring includes a 2A protection fuse. The power supply voltage must be in the 10-35 Vdc range.
1.3.1 How to connect the GNSS receiver to G7 Dataseed The All in One RTK receiver is equipped with a cable with a 9-pin serial connector that transfers data and power between the G7 Dataseed and the receiver. With the device off, connect the receiver cable to the harness connector labeled “GPS”.
Figure 1.3.3.b - Receiver installation in the center of the planter 1.3.3.2 Weeder installation Example of installation on a weeder. The receiver must be positioned exactly in the center of the tool. Figure 1.3.3.c - Receiver positioned in the center of the weeder Farmnavigator G7 Dataseed – User Manual...
The measurement must be entered in the receiver configurations on the G7 Dataseed. To configure the receiver at the end of the installation, read paragraph 2.3.1 Figure 1.3.4.a - Measuring the height from the ground...
Page 7
1. Press and hold the power button for 2 to 3 seconds; 2. Press “YES” to turn the device off. It is possible to reset G7 Dataseed if the device cannot be normally turned on/off. The reset button is located at the left of the power button, below the plastic cover.
1.5 How to use multi-touch display G7 Dataseed is provided with a multi-touch display which allows you to perform specific actions with your fingers. Tap the screen to select a button from the menu.
Page 9
The connection scheme of ECU Dataseed is as follows: CONTROLLER LEFT Electro valve left movement RIGHT Electro valve right movement Battery - Battery + Figure 1.6.a - ECU Dataseed connection scheme Figure 1.6.b - Example of connection of solenoid valve Farmnavigator G7 Dataseed – User Manual...
ECU. the “Controller” port; - Check that the ECU Dataseed is correctly powered (LED on); - Start a registration of a track / open and repeat a saved track. Farmnavigator G7 Dataseed – User Manual...
Page 11
- Check the connection of mode) RIGHT and LEFT; - Check the correct hydraulic supply; - Check the correct functioning of the hydraulic part. Table 1.6.1.a - ECU Dataseed troubleshooting Farmnavigator G7 Dataseed – User Manual...
Figure 2.0 - Main menu 2.1 Recording a sowing track Track logging is the basic functionality of the G7 Dataseed system. G7 Dataseed can store and organize with precision all the information relative to the sowing tracks recorded. Correct data entry, before starting recording, will be very useful during the weeding phase, when repeating the saved track.
Page 13
While recording a track, it is not possible to switch to “Automatic” mode (the button becomes active only when a previously recorded track is selected); Farmnavigator G7 Dataseed – User Manual...
Page 14
During the recording it is possible to pause the recording of the points by tapping the “PAUSE” button; Figure 2.1.c - End track registration Farmnavigator G7 Dataseed – User Manual...
2.2 Weeding phase: repeating the sowing track One of the strengths of G7 Dataseed is the ability to repeat with extreme precision a previously recorded track and automatically control a weeder equipped with a shifting frame.
Page 16
In the work page (repeating track mode), the saved track is shown in black, while the “RECORDING” button is disabled. Figure 2.2.c - Track to be repeated in automatic mode To start automatic weeding control: -Position the weeding implement near the track to follow; Farmnavigator G7 Dataseed – User Manual...
Page 17
On the right side of the work page there some icons for interacting with the shifting frame control system. In detail: AUTO: In this mode, the translator moves in automatic mode precisely following the track saved previously. MANUAL: In this mode, there is no automation. Farmnavigator G7 Dataseed – User Manual...
With the ECU connected, press and hold the button to move the tool to the right ECU ERROR: There is no communication between G7 Dataseed and ECU Dataseed. Check the power supply and the connection on the “Controller” connector. Table 2.2.f - Work page icons ( repeating track mode ) 2.3 Setup...
Page 19
G7 Dataseed is compatible with the All in One RTK receiver. The fundamental configurations for the correct use of the system are the following: Figure 2.3.1.b - Satellites - Satellite fundamental configurations Antenna position Figure 2.3.1.c - Antenna position settings...
Page 20
NOTE: FARMNAVIGATOR GNSS receivers include the receiver and the antenna in one housing. ‘Antenna position’ setting refers to the center of the outer case. 1. Tap “RECEIVER POSITION”; to set the offset and height of the receiver from the ground;...
Finally, to work with centimeter accuracy, the NTRIP settings must be correctly configured. In the menu, make sure that the “NTRIP CLIENT (EXTERNAL)” is set as “Connected”. 2.3.2 Guidance Options Figure 2.3.2.a - Guidance options Farmnavigator G7 Dataseed – User Manual...
Figure 2.3.5.a - User preferences menu 2.3.6 Remote control In the “Remote control” menu it is possible to pair the G7 Dataseed to the remote control (available as an accessory). To enable communication between the remote control and the G7 Dataseed: 1.
Figure 2.3.6.a - Remote control pairing 2.3.7 Wi-Fi The “Wi-Fi” menu allows you to connect G7 Dataseed to a local Wi-Fi network. 2.3.8 Mirror control Install the Mirror Control app to control G7 Dataseed with your smartphone or tablet (Android or Apple devices).
In the “System info” menu it is possible to view the current software version. If the wireless connection is active, you can search for updates by tapping the “Check for updates” button. Figure 2.3.9.a - System info 2.4 Database Figure 2.4 - Database Menu Farmnavigator G7 Dataseed – User Manual...
All recorded tracks are saved in the “TRACKS” menu: -Tap on the name of the track to access all its information (“DATA” tab); -Tap on the “PREVIEW” tab to view the track Figure 2.4.1.b - Track preview Farmnavigator G7 Dataseed – User Manual...
CSV, KMZ, SHP. The file is saved on the MicroSD memory card or on USB memory if connected to the device. Figure 2.4.1.c - Track export in various formats 2.4.2 Fields Figure 2.4.2.a - Fields database Farmnavigator G7 Dataseed – User Manual...
In the “FIELDS” menu it is possible to add a new field, to rename it or delete it. 2.4.3 Farmers In the “FARMERS” menu it is possible to add a new customer, to rename or delete it. Figure 2.4.3.a - Farmers database Farmnavigator G7 Dataseed – User Manual...
2.4.4 Drivers In the “DRIVERS” menu it is possible to add a new driver, to rename or delete him. Figure 2.4.4.a - Drivers database Farmnavigator G7 Dataseed – User Manual...
3. Other Functions 3.1 Software Update via Wi-Fi G7 Dataseed can be updated by connecting the device to a Wi-Fi network (even from a smartphone via a Wi-Fi hotspot / router). To search for and install available updates: 1. Connect G7 Dataseed to a Wi-Fi network;...
-The power for the camera must be supplied externally -The camcorder must have a male RCA connector. Connection of the video camera to G7 Dataseed is possible via the ‘USB / Video in / Ethernet’ (P/N AvMap: K2CYFS1000). The cable has a female RCA analog video input.
Page 31
It is recommended to always use protective devices. The voltage from pin2 is for signal use only. Once the device is connected, when the contact is closed, the G7 Dataseed activates the recording of the track. Conversely, when the contact is open, the recording is paused.