Related Manuals for Avonic AV-MT200
Summary of Contents for Avonic AV-MT200
- Page 1 USER MANUAL Avonic Wall Mount AV-MT200, AV-MT220 www.avonic.com • © July 2022 • Version 1.1...
-
Page 2: Disclaimer And Contact
“look and feel” and arrangement of such Content, contained in this Manual is owned, controlled or licensed by or to Avonic, and is protected by trade dress, copyright, patent and trademark laws, and various other intellectual property rights and unfair competition laws. -
Page 3: Important Information
IMPORTANT INFORMATION Liability Avonic will NOT be held responsible for any damage or injury caused by unqualified persons carrying out these tasks, or by not following the instructions in this Manual. Intended Use and Non-Intended Use Installation The following applies to the installation of the mount and the camera: •... -
Page 4: Symbols Used In This Manual
Symbols Used in This Manual Symbol Meaning Description Not following the instructions associated with this symbol may lead to Danger life-threatening situations and / or serious damage to the Product. Not following the instructions associated with this symbol may lead to Warning personal injury and / or serious damage to the Product. -
Page 5: Table Of Contents
Contents DISCLAIMER AND CONTACT........................ ii IMPORTANT INFORMATION........................iii Liability............................iii Intended Use and Non-Intended Use..................iii Installation..........................iii Operation.......................... iii Important Precautions......................iii Symbols Used in This Manual....................iv Acronyms............................ iv INTRODUCTION............................6 Purpose of This Manual......................6 Target Audience.........................6 Document Structure........................6 SAFETY INSTRUCTIONS........................... 7 Important Precautions........................7 Intended Use..........................7 Handling..........................7... -
Page 6: Introduction
Note that this is ONE manual for both mounts and that the mounts are separately sold. In this Manual the Avonic MT200 and MT200 Wall Mount is referred to as the 'Product'. If you want to use the mount and camera in combination with the CamDirector, you need to make sure that the MT200 is NOT compatible in combination with such a system! Use the MT220 to do this. -
Page 7: Safety Instructions
• Mount this Product to a wall or mounting pole. • ONLY use an Avonic mount for mounting to a wall or mounting pole. • Ensure the mounting construction is capable of supporting four times the weight of the Product. (See 'General Specifications >... -
Page 8: Ventilation
• Don’t open this Product and don’t attempt to repair it yourself. Disassembling the Product may damage it or may cause injury to you. • If this Product is damaged, malfunctioning, or if it comes into contact with liquid, contact Avonic or an Avonic Authorized Service Provider. -
Page 9: Product Overview
Description The Avonic MT220 and MT200 Wall Mount are both solid wall mounts suitable for the support of one or two CM40 or CM70 series PTZ cameras. Its discrete design matches the silent operation of Avonic PTZ cameras. The wall mount is a beautiful extension that not only ensures great and safe support of the PTZ cameras, but also allows for all the cables to be hidden inside the mount. -
Page 10: Unpacking
Take note that the mounts are separately sold! Check only the package contents for the mount you have. Quantity Description Avonic SKU MT200 MT220 1 pc 1 pc Wall Mount AV-MT200-B/ -W AV-MT220-B/ -W 1 pc 3 pc Black 30MM Cover Cap 1 pc 1 pc 30MM Steel Ring for Truss Mount 1 pc 2 pc 1/4”- UNC Pozidrive screw (20mm) to fasten... -
Page 11: Unpacking The Mount
MT220 in plastic bag MT200 in plastic bag 3. Verify that the plastic mount bag is sealed. If this is NOT the case, contact Avonic and stop here. 4. Break the seal of the sealed mount bag. 5. Take the mount out of the bag. -
Page 12: Mounting And Installation
• Mount this Product to a wall or mounting pole. • ONLY use an Avonic mount for mounting to a wall or mounting pole. • Ensure the mounting construction is capable of supporting four times the weight of the Product. (See 'General Specifications >... -
Page 13: Mounting The Camera
Figure 2: Screws and plugs The screws and plugs are not included. See Package contents what is included. 2. Mounting the Camera 2. Place the CM40 or CM70 camera on its baseplate and mount it to its baseplate using the supplied 1/4”... -
Page 14: Cable Cover
3. Cable Cover 4. Put the cable cover over the back of the bracket, neatly concealing the cables and connectors of the camera. Note that the MT220 have a bigger cover than you can see on the pictures below. The cover cap can be screwed in place using the supplied M6 Allen bolts (Figure 9) for the MT200 as well as the MT220. -
Page 15: Mounting On A Mounting Pole
Mounting on a mounting pole Trussmount clamp and mounting pole Trussmount clamp If you use the MT220 in combination with a Trussmount Clamp, make sure that you use the hole in the CENTER of the baseplate. Otherwise the mount could tilt to one side. Follow the instructions below to use a Trussmount Clamp: 1. -
Page 16: Measurements And Specs Mt200
MEASUREMENTS AND SPECS MT200... -
Page 17: General Specifications
General Specifications Color White, Black Dimensions product MM 2370 x 60 x 130 mm (indicative) (W x H x D) Weight product 1060 Kg (indicative) Included MT200 Wall Mount, 1x Black 30MM Cover Cap, 1x 30MM Steel Ring, 1x 1/4”- UNC Pozidrive screw to fasten camera, M6*10mm 2x Allen Bolt screw, M3*6mm DIN9785 5x Pozidrive security screw... -
Page 18: Measurements And Specs Mt220
MEASUREMENTS AND SPECS MT220... -
Page 19: General Specifications
General Specifications Color White, Black Dimensions product MM (W x H x D) 2370 x 57 x 2628 mm Weight product 2.1 KG Dimensions package MM (W x H x D) 2480 x 65 x 3400 mm Weight package 2.4 KG Included MT220 Double Wall Mount, 3x Black 30MM Cover Cap, 1x 30MM Steel Ring,... -
Page 20: Transport And Storage
TRANSPORT AND STORAGE The mount must be transported in its original packaging box. Inside the box, it is recommended to wrap the mount in the original plastic bag and to place it in the protective foam. Specific guidelines apply to the environmental temperature and humidity when operating and storing the mount and the camera. -
Page 21: Disposal And Recycling
In general, the term 'E-Waste' applies to items of all types of electrical and electronic equipment and its parts that have been discarded by the owner as waste without the intention of re-use. Avonic outsources the disposal and recycling of its E-Waste mount and camera materials to the Stichting Open. https://stichting-open.org/... - Page 22 Avonic Wall Mount AV-MT200, AV-MT220 © July 2022 • Version 1.1 Exportweg 11a • 2645 ED Delfgauw • The Netherlands +31(0)15 7112 712 • info@avonic.com • www.avonic.com...
Need help?
Do you have a question about the AV-MT200 and is the answer not in the manual?
Questions and answers