Summary of Contents for Demtech ART-0100/A SRT-0200/A
- Page 1 SRT/ART Removal Tool Operator’s Manual Model Numbers: ART-0100/A SRT-0200/A Revision: A...
- Page 2 DEMTECH Services, Inc. developments. The material in the manual is for informational purposes only and is subject to change without notice. DEMTECH Services, Inc. assumes no responsibility for any errors that may appear in this manual. Printed in the USA Manual Number: SRT-OPERATORS-MANUAL, Revision: A DEMTECH Services, Inc.
-
Page 3: Table Of Contents
Rev. A, March 2022 Table of Contents SAFETY PRECAUTIONS………………………………………………….PAGE 1 GENERAL SAFETY & MAINTENANCE INFORMATION……………PAGE 2 Intended Use…………………………………………………………Page 2 Maintenance…………………………………………………………Page 2 GENERAL PRODUCT DATA……………………………………………...PAGE 3 SITE PREPARATION……………………………………………………….PAGE 3 WHAT’S INCLUDED………………………………………………………..PAGE 4 ... -
Page 4: Safety Precautions
Rev. A, March 2022 1 Safety Precautions Safety precautions for operating personnel and equipment: WARNING 1: Operating personnel should perform only the procedures described and recommended in this manual. WARNING 2: To avoid serious injury ensure all hardware is fastened prior to use. WARNING 3: The locations of potentially dangerous voltages and other hazards are identified and labeled on the equipment. -
Page 5: General Safety & Maintenance Information
Maintenance, inspection and adjustment of the SRT shall only be carried out by qualified personnel. Before removing or installing spare parts or performing other repair operations to the SRT, consult DEMTECH Services, Inc. or your authorized DEMTECH service center for advice on proper procedures. This will help insure a safe and successful outcome. -
Page 6: General Product Data
SRT, is a durable easy to use non-destructive on-site Stud Removal Tool. This design allows for easy high-volume removal of rows of Studs and/or Anchors from concrete embedment liner. DEMTECH Services, Inc. strives to make our systems easy to use and built to last. -
Page 7: What's Included
Rev. A, March 2022 5 What’s Included SRT-0200/A 1X SRT‐030 1X SRT‐035 1x SRT‐040 1X SRT‐015 3x 8‐32 – ½” Screws 2X 22mm Wrench ART-0100/A 1X ART‐025 1X ART‐010 1x SRT‐020 1X SRT‐015 3x 8‐32 – ½” Screws 2X 22mm Wrench Page 4 SRT Operator’s Manual... -
Page 8: Setting Up Your Art/Srt Removal Tool
Prior to Stud removal, ensure the correct attachment plate has been selected. A labeled machine and transverse attachment plate has been provided. This allows users to remove Studs in any direction (See Figure 5.1). Contact DemTech Services to ensure you have the correct attachments for the job. -
Page 9: Installing Attachment Plate
Rev. A, March 2022 Installing Attachment Plate a. Install 3x screws (Item 2, Figure 5.2) into router housing using a Phillips head screwdriver. 1 2 2 2 Figure 5.2 Page 6 SRT Operator’s Manual... -
Page 10: Setting Cut Depth
Rev. A, March 2022 Setting Cut Depth a) Unclamp Item 1, Figure 5.3. b) Press both levers (Item 2, Figure 5.3) in and adjust router base height. c) Ensure the router bit is flush to bottom of the attachment plate (Item 3, Figure 5.3). 1 ... -
Page 11: Changing Bits
Rev. A, March 2022 d) Once the router attachment is flush to the liner, flip the power switch (Item 1, Figure 5.4) to the ‘ON’ position. Note, router shown without power cord. 1 Figure 5.4 Changing Bits a) Prior to changing bits, ensure no attachment plate is fastened to Router. Utilize provided Wrench set to loosen the Router Bits collet. -
Page 12: Factory Servicing
Refer to the following step for preparing the V-Plate for return. Unless previous arrangements are made, shipping charges and insurance are the responsibility of the customer. Ship the packaged V-Plate to DEMTECH Services, Inc. at: DemTech Services, Inc... - Page 13 At DEMTECH Services, Inc.'s option, a service representative may be dispatched to the equipment location. As an additional protection, DEMTECH Services, Inc. warrants that for a period of 90 days from the date of shipment to the original buyer, pending prior authorization from DEMTECH Services, Inc., there will be no charge for service related shipping of parts and/or equipment or for authorized travel of a service representative to the equipment location.