Monolith C Series Components List Technical Data Before you Install Installation ADA Compliance Operation Maintenance Cleaning Repairs Damage Prevention Faucets Soap Dispensers Warranty MONOLITH BASIN SYSTEM MANUAL...
Monolith C Series The Splash Lab Monolith System C Series is a trough sink specific to wall-mounted fixtures for one to four users. The basin is constructed from solid surface material, mounted on steel brackets and is well suited to commercial and public restrooms.
Lock nuts 1/4-20 UNC Washers Before assembly, please check that all listed components are present and advise The Splash Lab of any missing parts. Wall mounting hardware is not included for fastening the brackets to the wall as every location differs. The Splash Lab recommend that you consult the Structural Engineer or General Contractor for advice on the most appropriate mounting method for your project.
Page 6
/ steel stud wall The wall structure that the Monolith is to be fixed to should be sufficiently strong to support the weight of the Monolith. Refer to table on page 5 for weight of the Monolith.
Page 7
/ timber stud wall It is recommended that a timber stud framework is constructed to support the Monolith using construction- grade 2” x 4” studs. This will leave enough void within the wall for the required services for the plumbing installation.
3-User 90” Monolith P-Trap Connection Waste Connection Ensure a water supply is provided to suit the taps in use with Monolith. A waste water connection and appropriate trap is required to connect to the 1 ½” NPT thread on the waste funnel.
Page 9
3-User 90” Monolith 1-1/2" P' Trap T. M.V. Hot Feed Cold Feed Waste Water Required materials not included Hardware Fasteners 3/8” x 2” Lag screws 2 per bracket Plumbing 1 1/2” NPT P-trap 1 per user 1 1/2”...
Length of trough No of Fixing height Suggested bracket (inches) brackets – Point A fixing centers 32 1/8 3-User 90” Monolith 20" to 36" Depending 20" to 36" Depending 20" to 36" Depending 4.00 TYP. on sink design...
Page 11
Mark the bracket mounting points on Drill the wall to accept the 3/8” x 2” lag screws. the wall. Attach the brackets through the mounting slots Ensure all brackets are level with each other with the lag screws using the height adjustment to lengthwise, at the correct height, and mounted ensure that all the brackets are all level and fitted...
Page 12
With the Monolith placed face-down, fit all waste Lift the Monolith onto the brackets and make funnels and gaskets to the funnel adapter plates sure the T-slot bolts pass through the slots on on the underside of the basin. Install one bolt into the mounting brackets each T-slot pad.
Page 13
Fit waste trap to drain funnel MONOLITH BASIN SYSTEM MANUAL...
ADA compliance 24.00 17.85 14.66 5.00 38.00 34.00 29.00 27.00 9.00 11.00 6.00 ADA KNEE AND FOOT CLEARANCE ZONE 17.00 7.00 MONOLITH BASIN SYSTEM MANUAL...
operation The user is to activate the faucet, either an automatic sensor faucet or a manual faucet, allow the water to flow and wash their hands in the normal manner. maintenance The Monolith should be periodically inspected for any damage. Also, the Monolith should be tested to ensure that the water drains out of the basin, and that the drainage waterways are not blocked with any debris.
Severe scratches can be removed using 180G abrasive paper in a circular motion on the affected area. Most other damage or chips to The Splash Lab Solid Surface material can be repaired with no visible evidence. Please contact The Splash Lab technical department for damage evaluation and repairs.
Some chemicals are not compatible with The Splash Lab solid surface. Contact should be avoided with the following chemicals: Strong chlorinated solvents Chloroform Ketones Methylene chloride (paint removers) Very strong acids such as concentrated sulphuric and hydrochloric acids Acid drain cleaners should not be used.
1 year for manufactured product; 10 years for material used If a defect is found in normal use, The Splash Lab will, at their discretion, repair, provide a replacement part or product, or make appropriate adjustments. Damage caused by accident, misuse, or abuse is not covered by this warranty.
Page 19
contact General information 310 410 5008 Showroom: 8745 Washington Boulevard, Studio D, Culver City CA 90232 Warehouse + Offices: 20809 Higgins Court, Torrance CA 90501 Technical support info@thesplashlabusa.com For further contact information visit: www.thesplashlabusa.com MONOLITH BASIN SYSTEM MANUAL...
Need help?
Do you have a question about the MONOLITH C Series and is the answer not in the manual?
Questions and answers