Before First Use; Intended Use; Operation; Accessories - Batavia FIXXPACK BT-CP002 Operating Instructions Manual

English
machine may contact hidden wiring a
"live" wire may make exposed metal
parts of the power tool "live" and could
give the operator an electric shock.
• In case of electrical or mechanical mal-
function, immediately switch off the
tool or unplug charger from power
source.

5. Before first use

Remove the machine and the accessories
from the packaging. Check the machine for
transport damage and do not use the
machine in case of damages. Keep the
packing materials away from children, risk
of suffocation!

6. Intended use

This power tool is to be used as a polisher
and sandpaper sander, it is not suitable for
cutting, roughing and wire brushing. Do not
use any accessories that have not been
specifically provided or recommended for
this power tool by the manufacturer.

7. Operation

Spindle lock function
7.1
Press the spindle lock (1) to prevent spindle
rotation when installing or removing

accessories

2-gear speed
7.2
The speed can be adjusted by the 2-gear
speed button (3) between a high speed
0-7800/min or a lower speed 0-2600/min
Lock button
7.3
Before use, press the lock button (5) on
the side with the symbol to unlock the
ON/OFF switch (8), then press the ON/
OFF switch (8).
a. After use, release the ON/OFF switch,
then press the lock button on the side
with the symbol to lock the ON/OFF
switch.
On/Off Trigger
7.4
• Use the On/Off trigger to start the
machine and keep holding it for contin-
uous operation.
• The rotation speed can be varied by
depressing the On/Off trigger. The more
the trigger is pressed, the faster the
rotation speed.
6
7064218-Cordless-Polisher-Ma-EN-WoF-2203-22.indb 6 7064218-Cordless-Polisher-Ma-EN-WoF-2203-22.indb 6
• To switch the machine off, release the
On/Off trigger
8. Accessories
Use only accessories with an allowable
speed matching at least the highest no-load
speed of the tool.

9. Maintenance and Cleaning

WARNING: Always disconnect from the
mains power supply, before carrying out any
maintenance/ cleaning of the charger.
Remove the battery before carrying out any
maintenance/cleaning of the tool.
Maintenance
9.1
There are no inner parts of the tool which
need maintenance.
Cleaning
9.2
• Keep safety devices, ventilation open-
ings and the motor housing as free as
possible from dirt and dust. Rub the
electric power tool with a clean cloth or
blow over it with low pressure com-
pressed air.
• We recommend that you clean your
electric power tool immediately after
each use.
• Clean the electric power tool regularly
with a damp cloth and somewhat soft
soap.
Do not use any cleaning or solvent materi-
als; these can attack the device's plastic
components. Make sure that no water can
get inside the electric power tool.

10. Technical data

Speed . . . . . . . . . . 0-2600/0-7800 min
Pad size . . . . . . . . . . . . . . . . Ø 75mm
Drive spindle thread . . . . . . . . . . . . .M6
Weight. . . . . . . . . . . . . . . . . . 0.67 kg
Sound Pressure Level L
Uncertainty K . . . . . . . . . . . . . . . 3 dB
pA
Sound Power Level L
WA
Uncertainty K . . . . . . . . . . . . . . 3 dB
WA
Hand Arm Vibration
Main handle . . . . . . . . . . . . 4.700 m/s²
Uncertainty K. . . . . . . . . . . . . .1.5 m/s
Auxiliary handle . . . . . . . . . . 3.334 m/s
Uncertainty K. . . . . . . . . . . . . .1.5 m/s
-1
. . . . . 80 dB(A)
pA
. . . . . . . 91 dB(A)
2
2
2
22-03-2022 12:07 22-03-2022 12:07