Paslode C Series Operating Manual And Tool Schematic
  1. Manuals
  2. Brands
  3. Paslode Manuals
  4. Power Tool
  5. C Series
  6. Operating manual and tool schematic
Paslode C Series Operating Manual And Tool Schematic

Paslode C Series Operating Manual And Tool Schematic

Paslode pneumatic straight bradder
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
P
IMPORTANT!
DO NOT DESTROY
It is the customerʼs responsibility to have all
operators and service personnel read and
understand this manual.
PRINTED IN TAIWAN
© 2017, Illinois Tool Works Inc.
219495-1
08/17
OPERATING MANUAL AND
TOOL SCHEMATIC
Part No. B20118
MODEL T250-16S
Paslode Pneumatic
Straight Bradder

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the C Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Paslode C Series

Summary of Contents for Paslode C Series

  • Page 1 Part No. B20118 MODEL T250-16S Paslode Pneumatic Straight Bradder IMPORTANT! OPERATING MANUAL AND DO NOT DESTROY TOOL SCHEMATIC It is the customerʼs responsibility to have all operators and service personnel read and understand this manual. PRINTED IN TAIWAN © 2017, Illinois Tool Works Inc.
  • Page 2 Paslode replacement parts,damaged in transit or handling, or which, in Paslode's opinion, has been altered or repaired in a way that affects or detracts from the performance of the tool. PASLODE MAKES NO WARRANTY, EXPRESSED OR...

  • Page 3: Tool And Fastener Specifications

    TOOL AND FASTENER SPECIFICATIONS TOOL SPECIFICATIONS MODEL NO. T250-16S (Part# B20118) HEIGHT 11.6" WIDTH 2.9" LENGTH 12.3" WEIGHT 3.9lbs. OPERATING PRESSURE 80 to 120 p.s.i. (5.5 to 8.3 bars) FASTENER SPECIFICATIONS NAIL LENGTH 1" - 2-½" SHANK DIAMETER 16 gauge (1.6 mm) TOOL AIR FITTINGS This tool uses a 1/4”...

  • Page 4: Safety Instructions

    fire unexpectedly. WARNING Failure to follow any of the above instructions could result in severe personal injury to tool user and bystanders or cause damage to tool and property. Contact your local Paslode Representative for presentation of Paslodeʼs Safety Awareness Program...

  • Page 5: Tool Operation

    Paslode standards could cause tool damage and will void all warranty claims. Loading Fasteners STEP 1: Align the heads of the Paslode 16 ga. (1.6 mm) Finish nails to the brad channel in the rear of the magazine and insert one or two strips. Push the nails strips forward.
  • Page 6 Unload Nails: To unload nails, simply pull the follower to the rear of the The Paslode T250-16S Finish Nailer has a triggering magazine and press the center lock button on the follower. system than can be switched from sequential to contact The lock will move the follower out of the way and allow trip.

  • Page 7: Maintenance

    ❑ possible, the following procedure should be used to warm is legible. up the tools. Use only Paslode approved fasteners in the tool, and ❑ Reduce the regulated air pressure to 30 psi (2 Bar). ❑ ensure that they are correct for the application.
  • Page 8 Keep magazine and feeder Prevent jamming of fasteners. Blow clean daily. mechanism clean. Use only Paslode replacement Keep tool operating efficiently Order any replacement parts needed from Paslode Dealer. parts. and maintain Paslode tool warranty.

  • Page 9: Operator Troubleshooting

    Clean as needed to from time to time. remove debris. Make sure correct fasteners are being used. Use fasteners that meet Paslode specifications only. ® Increase air flow to tool -- use larger air lines (3/8 ID (10mm) minimum).
  • Page 12 ITW Construction, Asia pacific 47-55 Williamson Road,Ingleburn, NSW 2565 Paslode New Zealand 8 Orbit Drive, Albany, Auckland © 2017, Illinois Tool Works, Inc.

This manual is also suitable for:

T250-16s

Table of Contents