® The Impulse battery charger system meets all safety requirements for power tools. is a trademark Paslode CORDLESS An Ilinois Tool Works Company 888 Forest Edge Drive Vernon Hills, Illinois 60061 Power Nailers are made in the U.S.A. and are CORDLESS protected by one or more of the following U.S.
Paslode's sole liability hereunder will be to replace any part or accessory delivery to the original user. which proves to be defective within the specific time period. Any replacement...
An Overview of the Cordless Stapler Description Specifications Dimensions: Weight 6.5 lbs. The Cordless Stapler is a self-contained, fully portable tool Height 12-1/2 nches that uses liquid hydrocarbon fuel to power a unique linear Length 13-1/2 inches drive internal combustion motor. Cycle Rate: Intermittent Operation –...
The following safety instructions have been included in this booklet to provide you with basic information necessary for WARNING safe operation of the Paslode Stapler. DO NOT ATTEMPT TO OPERATE THIS TOOL UNTIL YOU HAVE READ AND UNDERSTAND ALL SAFETY PRECAUTIONS AND Do not expose the tool to MANUAL INSTRUCTIONS.
Page 6
Refer to the servicing or troubleshooting section of this manual to correct the problem. If the problem cannot be corrected, stop using the tool and report it to your The Cordless Stapler supervisor or Paslode ® representative. should be operated only when it is in contact with 6.
Page 7
Safety Instructions 12. NEVER DRIVE FASTENERS INTO AREAS WITH 15. PROPERLY STORE FUEL CELL. CONCEALED HAZARDS. Always check the area behind the work surface for WARNING electrical wiring, gas pipes, water pipes, sewer drains or other potential hazards. Always store fuel cells where they will not be 13.
Battery and Charging System Battery and Charging Sytem Charging Instructions The Paslode Cordless tool comes with a recharge- 1. Remove wall mount unit with the orange label from able battery and its own charging system. This the tool case and plug into a 120V AC outlet. Set...
Page 9
Battery and Charging System Battery Indicator Light The illustration is a close-up of the side of the Impulse Stapler handle. On the back side of the handle is a small plastic lens. This is the battery indicator light. When you insert a fully-charged battery into the tool, you will see a blinking green light.
Do not inhale the spray. NOTE: Altitude Restriction Keep out of the reach of children. Paslode Cordless tools are powered by an internal combustion engine and are effected by altitude. The Store fuel cell(s) in well-ventilated areas only. tool may lose power or not cycle consistently at elevations of 4000 feet or greater.
Page 11
Fuel Cell and Metering Valve Installing Metering Valve to Fuel Cell Prior to Use To install the metering valve to a fuel cell: 1. Press downward on the front side of the valve (stem side) until it seats. 2. Press downward on the rear side of the valve until it seats. 3.
Page 12
Fuel Cell and Metering Valve Inserting Fuel Cell As you slide the metering valve/fuel cell assembly into the Cordless Stapler, you will notice a yellow adapter at the top Inserting the metering valve/fuel cell assembly into the of the cylinder pocket. As shown in the illustration, this Cordless Stapler is very simple.
An overheated tool may not drive staples completely or may operate 2. Insert one or two strips of Paslode staples onto the rail. erratically. Let them fall forward to the staple guide. COLD WEATHER OPERATION 3.
Cordless Stapler Operation PRESS WORK – CONTACTING ELEMENT AGAINST THE WORK SURFACE. Fan motor starts, fuel is injected into combustion chamber and mixed with air by the fan. SQUEEZE Depth of Drive Adjustment TRIGGER Spark plug sparks Remove the battery before adjusting the depth of drive. and fuel/air mixture ignites.
Fasteners and Applications Fasteners Applications Vinyl Siding The Cordless S16 Stapler drives Paslode S16 Series staples. They are made from 16-gauge galvanized wire and Vinyl Clad Steel are entirely coated with Pas-Kote for improving holding power. Fasteners are collated into strips of 75 for easy Light Decking loading.
If you have any reason to believe that your problem is beyond the service procedures in this A typical problem you may encounter is having a jammed manual, contact your Paslode ® representative immediately. fastener. Because of the unique design of the Cordless...
Page 17
Cuts glare while affording eye protection. Clear Safety Glasses - Part No. 402510 Impulse ® Oil - Part No. 401482 Battery Charger Kit - Part No. 900200 Cordless Stapler Case - Part No. 900362 Contact your Paslode ® representative for additional information. ® Impulse Tools A 5/32 Hex Socket Wrench (Part No.
Spark wire out of spark plug. Remove cap and check spark lead, insert in spark plug and replace cover. Spark plug is dirty. Clean tool cylinder head. No spark is generated. Return tool to authorized Paslode ® dealer for service.
Page 19
Wrong fasteners being used. Use only fasteners meeting Paslode ® Tool operates, but no fastener is driven. specifications. Check Fasteners and Applications section for fastener types and sizes recommended for use in Impulse tool.
Page 20
IM200-S16 900078 PASLODE MODEL NUMBER DESIGNATION The model number of each Paslode tool contains information about the tool and the fasteners that are used with it. The following example illustrates the information contained in this tool model number. Stapler (16ga)