Summary of Contents for Kodak RODPJFFPVCW100
- Page 1 KODAK Projector Screen 100", 120" Fixed Frame, Black Velvet & White PVC User Mnual RODPJFFPVCW100 RODPJFFPVCW120...
-
Page 2: Table Of Contents
TABLE OF CONTENTS INTRODUCTION SAFETY PRECAUTIONS ABOUT SPECIFICATIONS PACKAGE CONTENTS PRODUCT OVERVIEW ASSEMBLY INSTRUCTIONS CARE & MAINTENANCE 10-12 WARRANTY INFORMATION GET IN TOUCH TO SEE THIS GUIDE IN FRENCH, ITALIAN, GERMAN, OR SPANISH, PLEASE VISIT WWW.KODAKPHOTOPLUS.COM OR USE THIS QR CODE: Um diese Anleitung auf Französisch, Italienisch, Deutsch oder Spanisch zu lesen, besuchen Sie bitte www.kodakphotoplus.com oder nutzen Sie diesen QR-Code. -
Page 3: Introduction
INTRODUCTION Thank you for purchasing the KODAK Projector Screen with Fixed Frame, Black Velvet & White PVC. This User Guide is intended to provide you with guidelines to ensure that operation of this product is safe and does not pose risk to the user. Any use that does not conform to the guidelines described in this User Guide may void the limited warranty. -
Page 4: About
Adult assembly required: Yes Installation required: No Additional tool required: Yes Country of origin: China Warranty included: Yes Warranty length: 1 year RODPJFFPVCW100 Overall screen size: 91.9" x 53.8" Viewing area size: 87.1" x 49" Diagonal size: 100" Black border length: 2.4" RODPJFFPVCW120 Overall screen size: 109.3"... -
Page 5: Package Contents
PACKAGE CONTENTS Screen fabric 8 Hanging brackets x 4 2 Metal rods x 6 9 Joint screws x 24 (extras included) (large x 2, medium x 2, small x 2) 10 Center joints x 2 3 Horizontal frames x 4 11 Plastic screen pins x 24 (extras included) 4 Vertical frames x 2 12 Center support bar... -
Page 6: Product Overview
REQUIRED TOOLS: 1 Philips-head screwdriver 2 Level 3 Pencil 4 Drill PRODUCT OVERVIEW 1 White PVC screen 2 Black velvet border ASSEMBLY INSTRUCTIONS 1. Clear out an area to assemble the screen. Measure the wall you wish to place the projector screen to make sure there is enough space for the screen. NOTE: Make sure the floor area you are using to assemble the projector screen is clean. - Page 7 2. Slide the two (2) joint bars into the flat ends of the horizontal frames, one (1) joint bar should be used to connect two (2) horizontal frames together. Then, secure the horizontal frames and joint bars together using the eight (8) joint screws, four (4) screws for each joint bar.
- Page 8 4. Slide the four (4) hanging brackets on the top and bottom horizontal frames right under the black velvet material. 5. Insert the corner joint into the horizontal and vertical frames then fasten corner joint to the frames using four (4) joint screws. Repeat this step for each corner to fully assemble the screen frame.
- Page 9 NOTE: The two (2) large metal rods should be inserted into the screen fabric vertically. The two (2) longer horizontal metal rods (connected by a small and medium rods) should be inserted into the screen fabric horizontally. 8. Push the screen pins attached to the frame through the small slots located along the edges of the screen fabric.
- Page 10 10. Place the assembled projector screen against wall and mark the desired location for the hanging screws with a pencil. push push NOTE: It is recommended to mount the projector screen at a height where your eye level sitting down lines up to the lower third of the screen for the best viewing experience upper 3rd Ideal viewing...
-
Page 11: Care & Maintenance
11. Drill four (4) holes into the wall where you marked. Then, insert the four (4) wall anchors into the drilled holes. 12. Insert the four (4) hanging screws into the wall anchors with a screwdriver or drill. Then, mount the screen on the screws with the hanging brackets. NOTE: The hanging brackets are loose and can slide along the frame so you can adjust the horizontal position of the projector screen if needed. -
Page 12: Warranty Information
WARRANTY LIMITED WARRANTY TO ORIGINAL CONSUMER This Kodak Projector Screen with Fixed Frame, Black Velvet & White PVC (“Product”), including any accessories included in the original packaging, as supplied and distrib- uted new by an authorized retailer is warranted by C&A Marketing, Inc. (the “Compa- ny”) to the original consumer purchaser only, against certain defects in material and... - Page 13 (g) Consumable parts, such as batteries, fuses, and bulbs; (h) Cosmetic damage; or (i) If any Kodak Projector Screen with Fixed Frame, Black Velvet & White PVC serial number has been removed or defaced. This Warranty is valid only in the country where the consumer purchased the Product, and only applies to Products purchased and serviced in that country.
- Page 14 EXTENT PERMITTED BY APPLICABLE LAW, THE COMPANY PROVIDES THE PRODUCT “AS-IS” AND “AS-AVAILABLE” FOR YOUR CONVENIENCE AND THE COMPANY AND ITS LICENSORS AND SUPPLIERS EXPRESSLY DISCLAIM ALL WARRANTIES AND CONDITIONS, WHETHER EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, QUIET ENJOYMENT, ACCURACY, AND NON-INFRINGEMENT OF THIRD-PARTY RIGHTS.
-
Page 15: Get In Touch
CUSTOMER SERVICE Should you experience any problems with your product, please contact us before returning the item to the place of purchase. We’re here to help! U.S. Support: kodak@camarketing.com 844-516-1539 International Support: kodakintl@camarketing.com 844-516-1540... - Page 16 The Kodak trademark, logo, and trade dress are used under license from Eastman Kodak Company. All other products, brand names, company names, and logos are trademarks of their respective owners, used merely to identify their respective products, and are not meant to connote any sponsorship, endorsement, or approval.