HP Compaq d240 MT Reference Manual

Service Reference Card
HP Compaq d240/d248 Series
Personal Computers
©
2003 Hewlett-Packard Development Company, L.P. The informa-
tion contained herein is subject to change without notice. HP shall
not be liable for technical or editorial errors or omissions contained
herein. Intel, Pentium, Intel Inside, and the Intel logo are trademarks
or registered trademarks of the Intel Corporation and its subsidiaries
in the U. S. and other countries.
Product of the United States.
Document Number 355870-001. 1st Edition December 2003.
Key Specifications
Processor Type: Intel Celeron or Pentium 4
RAM Type: DDR PC2100, PC2700, or PC3200 non-ECC
Maximum RAM Supported: 4 GB
Expansion Bus: PCI 2.2
Graphics Adapter Integrated controller. AGP support on select models.
Hard drive interface: UATA/100
I/O Interfaces: Serial (1), parallel (1), USB 2.0 (8), diskette drive (1)
System Setup and Boot
Basic system information regarding system information, setup, power management, hardware,
and passwords is maintained in the Setup Utility held in the system ROM. The Setup Utility is
accessed by pressing the F10 key when prompted (on screen) to do so during the boot sequence.
If the screen prompt opportunity is missed, a restart will be necessary.

Computer Setup Menu

Heading Option / Description
System Lists the following main system specifications:
Information
• Product Name
• Chipset type
• BIOS Version
• BIOS Release Date
• Processor Type
• Processor Speed
• CPU ID
Standard System Time (hh/mm/ss) - Allows you to set system time. (24 hour for-
CMOS mat)
Setup
System Date (mm/dd/yyyy) - Allows you to set system date.
Floppy Drive A - Calculates size and capacity of diskette drive.
Primary IDE Master - Auto detects which hard drive is the Primary
Master drive.
Primary IDE Slave - Auto detects which hard drive is the Primary Slave
drive.
Secondary IDE Master - Auto detects which hard drive is the Secondary
Master drive.
Secondary IDE Slave - Auto detects which hard drive is the Secondary
Slave drive.
Advanced Boot Device Specifies the boot order for all devices.
CMOS Priority
Setup
POST Delay Sets the amount of time before the Setup Utility prompt
Time (sec- (F10-Setup) appears when the computer boots.
onds) • None: POST delay time disable (Default)
• 5: POST Delay 5 seconds
• 15: POST Delay 15 seconds
• 25: POST Delay 25 seconds
• 35: POST Delay 35 seconds
System Key- Detects if a keyboard is present when the computer
board boots.
• Absent: keyboard not detected (default)
• Present: keyboard detected
APIC ACPI Enables or disables the internal I/O APIC and Multipro-
SCI IRQ cessor Tables. (Disabling the APIC ACPI SCI IRQ may
require you to reinstall the operating system.)
• Enable: IRQ 20-23 (Default)
• Disable: IRQ 01-11
Hyper- Enables or disables the Intel Hyper-Threading Technol-
Threading ogy. (This item is only selectable with the Intel HHT
Technology CPU plug-in.)
• Enable: Intel HTT function enabled (BIOS auto
detect)
• Disable: Intel HTT function disabled (BIOS auto
detect)
Internal Selects the size of memory for internal graphic adapter.
Graphic • Disable: Internal graphic memory mode select dis-
Mode Select
able
• 1MB: Share 1MB
• 4MB: Share 4MB
• 8MB: Share 8MB (Default)
• 16MB: Share 16 MB
• 32MB: Share 32 MB
Power Man- ACPI Sets the ACPI Standby State when system goes into
agement Standby ACPI Standby Mode.
Setup State • S1/POS: Power on Suspend
• S3/STR: Suspend to RAM (Default)
• L1 and L2 Cache Size
• Memory Information
• FSB Speed
• Ratio Status
• Ratio CMOS Setting
• DDR Frequency
• MAC Address
Computer Setup Menu (Continued)
Heading Option / Description
Power Man- Reset on AC/ Sets the system status after AC power loss.
agement Power Loss • Power Off: System always Powers Off (Default)
Setup
• Power On: System always Powers On
(Continued)
• Last State: System returns to the last state before AC
power loss
Resume on Sets the Resume on Ring from soft off.
Ring • Disable: Ring Resume disable (Default)
• Enable: Ring Resume enable
Resume on Sets the Resume on PME from soft off.
PME • Disable: PME Resume disable
• Enable: PME Resume enable (Default)
Peripheral OnBoard Enables or disables the OnBoard LAN.
Setup LAN • Disable: OnBoard LAN disabled
• Enable: OnBoard LAN enabled (Default)
OnBoard Enables or disables the OnBoard LAN Chip Boot ROM.
LAN Chip • Disable: OnBoard LAN Chip Boot ROM disabled
Boot ROM
• Enable: OnBoard LAN Chip Boot ROM enabled
(Default)
Init. Graph- Sets the initial priority of the graphics adapter
ics Adapter NR146 GV (d240/d248)
Priority • PCI/Int-VGA (Default)
• Int-VGA/PCI
USB Enables or disables the USB Controller.
Controller • Disable: USB Controller disabled
• Enable: USB Controller enabled (Default)
USB 1.1 Sets the USB 1.1 Device Legacy Support under DOS
Device Mode.
Legacy • Disable: USB 1.1 Device Legacy Support disabled
Support
• All Device: All devices are supported
OnBoard Sets the OnBoard Serial Port settings
Serial Port • Auto (Default)
• Disable
• 3F8/COM1
• 2F8/COM2
• 3E8/COM3
• 2E8/COM4
OnBoard Sets the OnBoard Parallel Port settings
Parallel Port • Auto (Default)
• Disable
• 378
• 278
Hardware CPU Warns when CPU temperature exceeds 85°/185°F.
Monitor Warning
Temperature
CPU System will shutdown when CPU temperature is greater
Shutdown than 90°/194°F.
Temperature
System Warns when system temperature is greater than 60°C/
Warning 140°F.
Temperature
System System will shutdown when system temperature is
Shutdown greater than 65°C/149°F.
Temperature
CPU Detects current CPU temperature
Temperature
System Detects current system temperature
Temperature
CPU FAN Detects CPU FAN speed
Speed
Chassis FAN Detects current chassis FAN speed
Speed
CPU VID Detects current CPU voltage
Vccp Detects current Vccp voltage
+1.5V Detects current ATX power +1.5V
+2.5V Detects current ATX power +2.5V
+3.3V Detects current ATX power +3.3V
+5.0V Detects current ATX power +5.0V
+12.0V Detects current ATX power +12.0V
HVcc Detects HVcc voltage
(+3.3VSB)
Password Change Allows you to set and change the supervisor password
Option Supervisor
Password
Password Shows password status
Status
Password Allows you to set the password check when the supervi-
Check sor password is set up
• Setup: Password prompt appears when BIOS is exe-
cuted
• Always: Password verification is checked every time
the computer boots (Default)
Load default None Loads the optimum default values for all of the setup
Settings options.
Save Set- None Exit system with new changes.
tings and
Exit
Exit With- None Exit system setup without saving the changes.
out Saving