1. Manuals
  2. Brands
  3. HP Manuals
  4. Desktop
  5. Brio 8500
  6. Online manual

HP Brio 8500 Online Manual

Brio pc
Hide thumbs Also See for Brio 8500:
Table of Contents

Advertisement

Quick Links

See also: User Manual
Online Reference Guide
HP
PC
Online Guide
Date: Spring1998

Advertisement

Table of Contents
loading

Related Manuals for HP Brio 8500

Summary of Contents for HP Brio 8500

  • Page 1 Online Reference Guide Online Guide Date: Spring1998...

  • Page 2: How To Use This Online Guide

    How to Use This Online Guide Click underlined red text to go to the topic indicated. The underlined red text is “linked” to Topic another topic in the guide. Click green text to go to the glossary, where a definition of the term is given. Glossary Click the Go Back button in the toolbar to go back to your previous place in the guide.

  • Page 3: Notice

    Notice Notice The information contained in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.

  • Page 4: About This Guide

    About This Guide This Online Reference Guide is broken down into three main sections: • About Your Hardware - information about the main hardware components that make up your computer: the system board, your sound card, your keyboard, and so on. •...

  • Page 5: Table Of Contents

    Your HP Enhanced Keyboard ........
  • Page 6 The HP Setup Program ........
  • Page 7 Upgrades and Accessories You Can Install..........Upgrading the BIOS.
  • Page 8 &...

  • Page 9: About Your Hardware

    About Your Hardware...

  • Page 10: A Quick Look Inside Your Computer

    A Quick Look Inside Your Computer System Board Layout The system board block diagram will help you identify where the different components and connections are located on the board. Power Supply Connector Rear Panel Connectors Processor and Socket Video Controller Expansion Card Slots COMBO Slot (PCI or ISA) Expansion Card Slot...

  • Page 11: Main Components And Features Of The System Board

    Main Components and Features of the System Board The main components and features of your HP BrioPCare: • Enhanced controller with two channels on the computer bus: A primary IDE channel used, for example, for one or two IDE hard disk drives.

  • Page 12: System Board Configuration Jumpers

    • Five expansion card slots for the installation of: Three 32-bit cards, two 16-bit Four 32-bit PCI cards, one 16-bit ISA card. PCI expansion card slots are generally white plastic grooves. Note ISA expansion card slots are generally black plastic grooves lined with silver. System Board Configuration Jumpers CMOS memory stores information, such as your computer’s configuration, which is preserved when you turn off your...

  • Page 13: Your Sound Card

    Your Sound Card Depending on the computer you have purchased, a sound card may be already installed. The sound card has several connectors that allow you to connect the card to other devices. The figure below shows where the connectors are located on the sound card.

  • Page 14: Connecting Audio Devices To The Rear Panel

    Connecting Audio Devices to the Rear Panel You can connect external speakers, a microphone, or other audio devices to the rear panel. Do not connect headphones to the jack on the CD-ROM drive, as this will only let you hear output from music CDs. Through the rear panel jack on your computer you will hear sounds from training presentations, CDs too.

  • Page 15: Connecting Audio Devices To The Internal Connectors

    Connecting Audio Devices to the Internal Connectors There are also several internal connectors located on the sound card itself. These are shown on are used are described below. This Auxiliary In Connector allows you to connect an additional internal audio source such as a TV tuner, or other similar card.

  • Page 16: Power Consumption

    For certain configurations, the power consumption values will be higher.       The power supply in your HP continues to supply power to the When the computer is turned off with the power button on the front panel, the power consumption falls below three Note watts, but it is not zero.

  • Page 17: Your Hp Enhanced Keyboard

    Your HP Enhanced Keyboard Depending on the computer you have purchased, you may have the HP Enhanced Keyboard. As well as offering standard keys, the Enhanced Keyboard allows you direct access to various software applications. You can also create your own shortcuts to your most frequent tasks by configuring certain keys.

  • Page 18: Using The Enhanced Keys

    The keys are located on the top right-hand side of the keyboard and can be used as follows: "# Messages and LED HP Brio Center Web Browser Displays a window showing the current configuration of the keys and the actions mapped to them.

  • Page 19: Configuring Keyboard Shortcut Keys

    Configuring Keyboard Shortcut Keys You have three standard configurable shortcut keys (S3, S4, S5). You can configure shortcut keys from the Control Panel. Double-click the Keyboard icon, then select the Shortcuts tab from the Keyboard Properties screen. To define a Shortcut key, you need to: Provide a Description of the application you are assigning to...
  • Page 20 You can also reconfigure the mail, phone, and power keys on your keyboard. Double-click the Keyboard icon, then select the Configuration tab from the Keyboard Properties screen. Launch your default mail client that has been configured in your Internet settings. Link to several telephone directories world-wide.

  • Page 21: About Your Bios

    About Your BIOS...

  • Page 22: The Bios In Your Computer

    You can configure certain aspects of your computer by using the Setup program which is part of the BIOS. Refer to HP Setup Program” on page 23 for more information about the Setup program. and is stored in a chip on the system board. A computer’s BIOS is specific to that...

  • Page 23: The Hp Setup Program

    Setup program’s default values. This should enable the computer to boot properly. HP strongly recommends that you make a note of any changes you make while in the Setup program. POST. Online help for an item on the Setup page 24 for instructions on how to use the key functions).

  • Page 24: Working Within The Setup Program

    Working Within the Setup Program The following key functions are available when using the HP Setup program. • arrows can be used to select fields in the current menu. • key moves the cursor to the top item, and the key moves the cursor to the bottom item of the current menu.

  • Page 25: Boot Device Priority

    2 About Your BIOS Boot Device Priority You can select the order of the devices from which the BIOS attempts to boot the operating system. During the POST, if the BIOS is unsuccessful at booting from one device, it will try the next one on the Boot Device Priority list until an operating system is found.

  • Page 26: Protecting Your Computer

    2 Select the Security menu group. Then enable the “Password on Boot” item. 3 Be sure to save your changes before you exit the Setup program. “The HP Setup Program” on page POST has completed, before the computer finishes its normal for an explanation on how to clear the CMOS.

  • Page 27: Power Management In The Bios

    IRQ signal sent by an expansion card (modem, network card, etc.). To customize the power management settings though the HP Setup program, use the main menu bar to the Power Menu. The item is then highlighted and displays the available power management options.

  • Page 28: Checking Your Configuration

    2 About Your BIOS Checking Your Configuration To view your computer’s current configuration, press the key just after your computer is turned on and while the computer’s logo is being displayed during the POST. The text-based POST screen will replace the computer’s logo, displaying the system components and devices. Press the Pause/Break key to “freeze”...

  • Page 29: Warning Messages And The Power-On Self-Test

    2 About Your BIOS Warning Messages and the Power-On Self-Test POST is executed each time the system is turned on or a reset is performed. The POST process checks that system components are operating correctly and initializes certain system parameters. Beep Codes If a terminal error occurs during POST, the system issues a beep code before attempting to display the error.

  • Page 30: How To Recover If Things Go Wrong

    Setup default values to recover. However, by doing this, you will lose all customized settings in the Setup program. These settings will have to be reconfigured. HP strongly recommends that you take note of any change to the system setup and store it in a safe place. If you Note have any doubts about using the HP Setup program, contact you HP-authorized support agent or reseller for help.

  • Page 31: Ventilator Fan Failure

    Switch off PC and verify fan connector Press <F1> to continue, <F2> for setup” HP strongly recommends that you do not press F1 to continue. Doing so may cause damage to your computer. Warning The fan connector should be checked before continuing. To check the fan connector do the following: 1 Remove the computer’s cover (refer to...
  • Page 32 The following table shows the possible pin settings: + ) $  *   Clear CMOS To clear the configuration: 1 Turn off the computer. Unplug the computer from the electrical socket. Disconnect any peripherals from the computer. The CMOS will be cleared only if the computer is unplugged from the electrical socket. Note 2 Remove the computer’s cover (refer to 3 Place the jumper on pins 2-3 (refer to...

  • Page 33: Upgrading And Adding Accessories

    Upgrading and Adding Accessories...

  • Page 34: Why Upgrade

    3 Upgrading and Adding Accessories Why Upgrade? Your computer uses some of the latest hardware technology to achieve outstanding performance. If required, performance can be even further enhanced thanks to this computer’s upgradeable design. Main memory is the workspace of the computer in which the processor stores all work in progress. You can increase the size of the computer’s workspace by adding more main memory.

  • Page 35: Upgrades And Accessories You Can Install

    Upgrades and Accessories You Can Install    For example, a sound card Contact your reseller for HP accessory part numbers † Sockets are shown filled. Empty sockets on your computer’s system board indicate that an upgrade is possible.    ·...

  • Page 36: Upgrading The Bios

    Hewlett-Packard are continually improving the BIOS in their computers, introducing new features and making them more efficient. You can therefore keep your own computer up-to-date by upgrading the BIOS. To upgrade your system BIOS, download the appropriate BIOS utility from our support site: http://www.hp.com/go/briosupport...

  • Page 37: Upgrading Hardware

    Upgrading Hardware For your safety, never remove the computer’s cover without first removing the power cord and any connection to a Warning telecommunications network. Always replace the cover before reconnecting any cables to your computer. Removing and Replacing the Cover You need to remove the computer’s cover to install accessories or to gain access to the system configuration jumpers.
  • Page 38 1 Turn off the computer and display, and disconnect all power supply cords and any telecommunications cables. 2 If necessary, unlock the cover using the key on the back panel. Remove the four screws from the back of the computer. 3 Pull the cover back 1.5 cm, then lift the cover completely off the computer’s chassis.
  • Page 39 3 Upgrading and Adding Accessories 4 Push the cover forward until it meets the front bezel. Secure the cover in place by replacing the four screws on the rear panel. If required, lock the cover using the key provided.     Note: on some computers the screw positions may be higher than shown 5 Reconnect the power supply cords and any telecommunications cables.

  • Page 40: Upgrading Main Memory

    The amount of main memory that your computer has depends on the particular model that you have. To see how much main memory is installed, right-click the My Computer icon on the desktop. Then click Properties in the drop-down menu.
  • Page 41 Installing Main Memory Modules 1 Remove the computer’s cover (refer to 2 On a table top turn the computer on to its side, with the system board closest to the surface of the table top. Static electricity can damage electronic components. Turn off all equipment. Don’t let your clothes touch the Caution accessory.
  • Page 42 If you experience any other problems as a result of the upgrade, and your computer is supplied with the HP Brio Center, refer to the support tools for further assistance.

  • Page 43: Upgrading A Processor

    New, faster processors are being developed all the time. Check with your reseller to find out the fastest processor that you can install in your computer. Information about processor upgrades is also available at: http://www.hp.com/go/briosupport "!
  • Page 44 Installing a Processor Upgrade Removing the Old 1 Remove the computer’s cover (refer to Processor 2 On a table top turn the computer on its side, with the system board closest to the surface of the table top. 3 Remove the airflow guide covering the processor: open the retaining clips on top of the airflow guide then lift it out of the computer.
  • Page 45 3 Upgrading and Adding Accessories 4 Squeeze the tabs on either side of the processor and gently pull the processor away from the system board . 1 Slide the new processor into the processor socket and push gently until it snaps into place (the processor can only go in one way) .
  • Page 46 Set the system board configuration jumpers (or jumper block). The following diagram shows the location on the system board of the jumpers used to configure the computer for the new processor. If you are in any doubt as to whether you should change jumper settings or not, contact your reseller. 1 Replace the airflow guide covering the processor.
  • Page 47 If you experience any other problems as a result of the upgrade, and your computer is supplied with the HP Brio Center, refer to the support tools for further assistance.

  • Page 48: Adding Accessories

    Adding Accessories Adding Expansion Cards An expansion card, or accessory board, is a component that usually adds some specialized function to a computer. For example, installing a network card can, in conjunction with the necessary software and cables, connect a computer to a network.

  • Page 49: Installing An Expansion Card

    Installing an Expansion Card Static electricity can damage electronic components. Turn off all equipment. Don’t let your clothes touch the Caution accessory. To equalize the static electricity, rest the accessory bag on top of the computer while you are removing the accessory from the bag.
  • Page 50 If Windows does not find the correct driver, it displays the following choices for you to select: • Windows default driver. (Shaded if the card is not known by Windows). If this option is available, select it. • Driver from disk provided by the manufacturer. If a Windows default driver is not available, and you have a driver disk, select this option.
  • Page 51 If you experience any other problems as a result of the upgrade, and your computer is supplied with the HP Brio Center, refer to the support tools for further assistance.
  • Page 52 Removing an Expansion Card You might need to remove an expansion card to install a component on it, or to improve access to components on the system board. 1 Follow steps “Installing an Expansion Card” on page 2 Unscrew and remove the retaining screw securing the card. Keep the retaining screw. 3 Carefully remove the card from its connector, handling the card at each end by its top edge.

  • Page 53: Installing Storage Devices

    The on-system board electronics have a total of six interface channels that can support up to six storage devices—two devices and four devices. Disk drives ordered from HP may be supplied with mounting rails. Remove all mounting rails from the drive, as your Note computer does not need them. You can install a non-IDE device such as a an interface card and software for it.
  • Page 54 Your computer has the following cables which may be used by storage devices: • A primary hard disk drive cable with two connectors. This cable supports up to two IDE hard disk drives, one of which is already connected to the Master connector on this cable. •...
  • Page 55 If you install a hard disk drive and connect it to the cable that the Note must be connected to the Master connector in the cable from the system board, not the Slave connector. If you have a CD-ROM drive currently connected to the Master connector, you must reconnect the CD-ROM drive to the Slave connector of the cable, and then attach the new hard disk drive to the Master connector.
  • Page 56 2 Install the new hard disk drive in the computer: • For a 3.5-inch hard disk drive – mount the new hard disk drive in the 3.5-inch bay (below the floppy disk drive). Have the connectors of the new hard disk drive pointing towards the back of the computer. •...
  • Page 57 If the new drive is not recognized, you may need to run the Setup program: restart the computer and press Press <F2> to enter SETUP is displayed at the bottom of the screen. If you have any doubts about using the HP Setup program, contact your reseller for help.
  • Page 58 Installing a Floppy Disk Drive, CD-ROM Drive, Zip Drive, or Tape Drive 1 To remove the front bezel, move the computer to the edge of the table (only far enough to be able to place your hand between the table and the front bezel). Pull the front bezel outwards from the computer by hooking your fingers in the gap and pulling (it should still be connected at the top).
  • Page 59 3 If you are installing a 3.5-inch drive, use a star-shaped screwdriver to unscrew the two screws on either side of the front plate and remove it. 4 If you are installing a 5.25-inch drive, remove the faceplate on the 5.25-inch bay by inserting a flathead screwdriver into the slot, then push outward until the faceplate snaps off.
  • Page 60 If the new drive is not recognized, you may need to run the Setup program: restart the computer and press Press <F2> to enter SETUP is displayed at the bottom of the screen. If you have any doubts about using the HP Setup program, contact your reseller for help.

  • Page 61: Changing The Battery

    Nevertheless, in order to protect the environment, do not dispose of batteries in household waste. Please return used batteries to the shop from where you bought them, to the dealer from whom you purchased your computer, or to HP so that they can be either recycled or disposed of in an environmentally sound way. Returned used batteries will be accepted free of charge.
  • Page 62 3 Upgrading and Adding Accessories...

  • Page 63: At Commands

    AT Commands...

  • Page 64: Basic At Commands

    Basic AT Commands This section describes the AT commands supported by your modem. If you send an AT command that is not applicable, the modem returns an error message. The following table lists the basic AT commands. Command See Modem Response Messages, on page Description 4 AT Commands $"...
  • Page 65 Command 0 to 9 - S= n - ;H - Description 4 AT Commands...
  • Page 66 Command Description 4 AT Commands...
  • Page 67 Command Description 4 AT Commands...

  • Page 68: Modem Response Messages

    Command Modem Response Messages In response to AT modem commands, the modem returns status information in the form of response messages. These messages appear on the screen when you enter a modem command and press Enter. You can instruct the modem to return responses in English language words (with the The most common responses are described in the table below (the numeric equivalents are in parentheses).
  • Page 69 4 AT Commands Message Description X2 X4...
  • Page 70 4 AT Commands Message Description...
  • Page 71 4 AT Commands Message Description...
  • Page 72 4 AT Commands Message Description...

  • Page 73: Glossary

    Glossary AGP Accelerated Graphics Port. Standard for computer bus architecture. BIOS Basic Input/Output System. Code within the computer that controls the input and output data. Bus An electrical connection over which information is transported. Cache A block of memory used for the temporary storage of data.
  • Page 74 Glossary I/O address Input/Output address. Address that defines the channel used between the main processor and a peripheral component. IRQ Interrupt Request. A signal that, when received by the processor, halts the current process and allows a different task to be undertaken. ISA Industry Standard Architecture.
  • Page 75 Glossary RAM Random Access Memory. Computer memory used to temporarily hold programs and data. Reset Reload operating characteristics. When you reset your modem, it obtains its operating characteristics from non-volatile random access memory where they are stored. Resolution How fine the detail is on a screen or printout.
  • Page 76 Glossary...

  • Page 77: Index

    Index Advanced menu HP Setup program AT commands list of audio devices, connecting Line In jack Line Out jack Mic jack SPK jack audio devices, connecting MIDI/GAME jack AUX In connector (MPEG) battery, changing Beep codes list of terminal errors...
  • Page 78 HP Setup program Line In jack Line Out jack main memory installing removing main memory module and sockets main menu HP Setup program...
  • Page 79 Index sound card internal connectors speakers, connecting SPK jack storage device connectors installing system board block diagram system board configuration jumpers system board features IDE controller main memory rear panel connectors system characteristics power consumption system recovery if incorrect password on startup the system startup fails you need to clear the CMOS tape deck, connecting...
  • Page 80 Index...

This manual is also suitable for:

Brio 8513Brio 8512Brio 8531Brio 8532Brio 8533Brio 85xx ... Show all

Table of Contents