HP ProCurve Gigabit-LX Installation Manual

Hp procurve gigabit-lx: install guide.
Hide thumbs
   
HP ProCurve Gigabit Transceivers
Installation Guide
Introduction
The HP ProCurve Gigabit Transceivers are used to provide 1000 Mbps
connections to other compatible network devices for the HP ProCurve
Switch 2424M Gigabit Stacking Module and other HP networking devices
that are designed to accept these transceivers. The transceivers are installed
into the transceiver slots of the HP networking device or device module.
This document describes how to install, verify, and troubleshoot the
following two HP ProCurve Gigabit Transceivers:
HP J4131A ProCurve Gigabit-SX Transceiver
HP J4132A ProCurve Gigabit-LX Transceiver
The Gigabit-SX transceiver complies with the 1000Base-SX standard and is
used with multimode fiber-optic cable. The Gigabit-LX transceiver complies
with the 1000Base-LX standard and is used with either single-mode or
multimode fiber-optic cable. For more information on the cables used with
these transceivers and the supported cable lengths, see page 4.
N o t e :
The illustrations in this document show the above listed units being used
with the HP J4130A ProCurve Switch 2424M Gigabit Stacking Module. The
procedures described in this document also pertain to using these units in
other Gigabit HP networking devices that are designed to accept them.
1

Advertising

   Summary of Contents for HP ProCurve Gigabit-LX

  • Page 1

    Switch 2424M Gigabit Stacking Module and other HP networking devices that are designed to accept these transceivers. The transceivers are installed into the transceiver slots of the HP networking device or device module. This document describes how to install, verify, and troubleshoot the...

  • Page 2: Installation Steps

    To install the HP Gigabit Transceivers, follow these steps: 1. Insert the transceiver into an HP networking device’s Gigabit transceiver slot and secure the retaining screws. 2. If the Gigabit transceiver slot is in a module, install the module into the switch.

  • Page 3

    Insert the Transceiver Into the Slot The transceivers are installed into an HP networking device, as follows: 1. Unplug the HP networking device from the AC power source, or remove the module with the transceiver slots from the networking device. Then, using a flat-bladed or Torx T-10 screwdriver, unscrew the two retaining screws on the slot cover plate or existing transceiver, and remove it from the HP networking device or device module.

  • Page 4

    Connect Network Cables to the Transceiver Port The following network cables should be used with the Gigabit-SX and Gigabit-LX transceivers. Port Type Gigabit-SX 62.5/125 m or 50/125 m core/ cladding diameter, graded-index, multimode fiber-optic cables that are fitted with SC connectors—the cables must comply with the ITU-T G.651 and ISO/IEC 793-2 Type A1b or A1a standards.

  • Page 5: Troubleshooting

    For additional troubleshooting, you can also use the device's console interface, the switch’s web browser interface, or HP Top Tools for Hubs & Switches to trouble- shoot and configure the Gigabit transceiver port. See the switch's Management and Configuration Guide for more information.

  • Page 6

    VCCI Class A Complies with Canadian EMC Class A requirements These transceivers are designed for operation with the HP ProCurve Switch 2424M or other HP networking products with compatible transceiver slots and are listed in the Declaration of Conformity for those products. See the Installation Guide for the network products, or contact your HP-authorized dealer or reseller for a copy of the declaration.

  • Page 7: Customer Support Services

    See the Customer Support/Warranty booklet that came with your transceiver for information on how to use these services to get technical support. The HP networking products World Wide Web site, http://www.hp.com/go/procurve also provides up-to-date support informa- tion and contact phone numbers. Click on the [Support] button on that web page.

  • Page 8

    Technical information in this document is subject to change without notice. Copyright Hewlett-Packard Company, 1999. All rights reserved. Reproduction, adaptation, or translation without prior written permission is prohibited except as allowed under the copyright laws. Printed in Singapore 03/99 Manual Part Number 5967-9960 *5967-9960*...

Comments to this Manuals

Symbols: 0
Latest comments: