Download Print this page

Mercia Garden Products 01OSBA0604SDFW-V1 General Instructions Manual

6x4 osb apex
Hide thumbs Also See for 01OSBA0604SDFW-V1:

Advertisement

Quick Links

General Instructions
01OSBA0604SDFW-V1 & OSBA0604SDFW-V1NW
6X4 OSB APEX
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand (not supplied)
including a Phillips screwdriver, Stanley knife, wood saw, step ladder and drill with 2mm
bit.
- Ensure there is plenty of space and a clean dry area for assembly.
TIMBER
As with all natural materials, timber can be a ected during various weather conditions.
For the duration of heavy or extended periods of rain, swelling of the wood panels may
occur. Warping of the wood may also occur during excessive dry spells due to an interior
moisture loss. Unfortunately, these processes cannot be avoided but can be helped. It is
suggested that the outdoor building is sprayed with water during extended periods of
warm sunshine and sheltered as much as possible during rain or snow.
Our buildings are pre treated with a water based treatment**; this only helps to protect
the product during transit and for upto 3 months against mould. To validate your
guarantee and ensure longevity of the product, it is ESSENTIAL the building is treated
with a wood preserver within the rst three months of assembly and thereafter in
accordance with the manufactures recommendations. Care must be taken to ensure
the product is placed on a suitable base.
BUILDING A BASE
When thinking about where the building and base is going to be constructed:
Ensure that there will be access to all sides for maintenance work and annual
treatment.
Ensure the base is level and is built on rm ground, to prevent distortion. Refer to
diagrams for the base dimensions, The base should be slightly smaller than the external
measurement of the building, i.e. The cladding should overlap the base, creating a run
o for water. It is also recommended that the oor be at least 25mm above the
surrounding ground level to avoid ooding.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Whilst all products manufactured are made to the highest standards of Safety and in
the case of childrens products independently tested to EN71 level, we cannot accept
responsibility for your safety whilst erecting or using this product.
Refer to the instructions pages for you speci c product code
Please retain product label and instructions for future reference
x2
All building's should be
erected by two adults
For ease of assembly, you
MUST pilot drill all screw
holes and ensure all screw
heads are countersunk.
2mm Drill bit
**Protim Aquatan T5 (621)**
Your building has been treated with Aquatan.
Aquatan is a water-based concentrate which is diluted with water, the building as been treated by the correct
application of Aquatan solution and then allowed to dry.
Aquatan is a decorative nish to colour the wood, which is applied industrially to timber fence panels and
garden buildings.
Aquatan undiluted contains: boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl
sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.
For assistance please contact customer care on: 01636 880514
Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN
www.merciagardenproducts.co.uk
Winter = High Moisture = Expansion
Summer = Low Moisture = Contraction
CAUTION
Every e ort has been made during the
manufacturing process to eliminate the
prospect of splinters on rough surfaces of the
timber. You are strongly advised to wear gloves
when working with or handling rough sawn
timber.
P 1

Advertisement

loading
Need help?

Need help?

Do you have a question about the 01OSBA0604SDFW-V1 and is the answer not in the manual?

Questions and answers

Summary of Contents for Mercia Garden Products 01OSBA0604SDFW-V1

  • Page 1 Please retain product label and instructions for future reference All building’s should be Winter = High Moisture = Expansion erected by two adults Summer = Low Moisture = Contraction 01OSBA0604SDFW-V1 & OSBA0604SDFW-V1NW 6X4 OSB APEX BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY For ease of assembly, you CAUTION...
  • Page 2: Pre-Assembly

    01OSBA0604SDFW-V1 & 01OSBA0604SDFW-V1-NW Please retain product label and instructions for future reference Pre Assembly Overall Dimensions: Remove transportation Length = 1794mm Width = 1199mm blocks from the bottom 01OSBA0604SDFW-V1 Height = 1863mm of each panel before Base Dimensions: beginning assembly. Each...
  • Page 3 Step 1 Step 3 Fix the corners with 50mm Place the floor on a firm and level base, screws as shown in diagram. ensure the base has suitable drainage free 9x50mm Screws from areas where standing water can collect. See the front page for base requirments. Pre drill hole 50mm...
  • Page 4 Step 5 Step 7 Fix two eaves frames to each roof sheet Pre drill 40mm hole using 3x30mm screws per eave. screw Cut the felt into 2 sheets at 1894mm and fix onto the roof Fix the roof sheets to the roof ensuring using felt tacks as shown in they come together at the top using diagram ensuring there is...
  • Page 5 Step 8 Step 10 For the no window version go to step 11 Fit the Cover Trims to the front Pre drill and back of the building as hole 30mm shown in the illustration using screw 30mm screws. Trim the length 30mm of the cover trims to the Fix the window strips to the two...
  • Page 6: After Treatment

    Step 11 Step 12 Fix the Turn Button onto the door gable using 1x30mm black screw for each one. 2x 30mm Black Screw 30mm screw It is ESSENTIAL that you apply wood treatment immediately after the building has been assembled. AFTER TREATMENT: score around protective cover on glazing and...

This manual is also suitable for:

Osba0604sdfw-v1nw