Foxwell NT710 Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Trademarks

FOXWELL is trademark of Shenzhen Foxwell Technology Co., Ltd.

All other marks are trademarks or registered trademarks of their respective

holders.

Disclaimer

The information, specifications and illustrations in this manual are based on the

latest information available at the time of printing.

Foxwell reserves the right to make changes at any time without notice.

Visit our website at

www.foxwelltech.us

For Technical Assistance, send us email at

support@foxwelltech.com

NT710 User's Manual V1.1

Table of Contents

Need help?

Do you have a question about the NT710 and is the answer not in the manual?

Questions and answers

Enrique Alonso

May 23, 2025

Necesito un manual foxwell NT710 en Español

thomas tran

April 27, 2025

is NT710 comparable with 2008 ML550 MBZ

Summary of Contents for Foxwell NT710

Page 1 Disclaimer The information, specifications and illustrations in this manual are based on the latest information available at the time of printing. Foxwell reserves the right to make changes at any time without notice. Visit our website at www.foxwelltech.us For Technical Assistance, send us email at support@foxwelltech.com...
Page 2: One-Year Limited Warranty
FOXWELL. 3 The customer shall bear the cost of shipping the product to FOXWELL. And FOXWELL shall bear the cost of shipping the product back to the customer after the completion of service under this limited warranty.
Page 3 The customer will be billed for any parts or labor charges not covered by this limited warranty. d) FOXWELL will repair the Product under the limited warranty within 30 days after receipt of the product. If FOXWELL cannot perform repairs covered...
Page 4 (the Consumer). This limited warranty gives the Consumer specific legal rights and the Consumer may also have other rights which vary from state to state. NT710 User's Manual V1.1...
Page 5: Safety Information
● Fuel, oil vapors, hot steam, hot toxic exhaust gases, acid, refrigerant and other debris produced by a malfunction engine can cause serious injury or death. Do not use the tool in areas where explosive vapor may collect, NT710 User's Manual V1.1...
Page 6 And never leave a running engine unattended. ● Do not wear jewelry or loose fitting clothing when working on engine. ● Don't connect or disconnect the equipments while the ignition is on or the engine is running. NT710 User's Manual V1.1...
Page 7: Table Of Contents
..........................21 CCOUNT 4.4 M .......................... 21 RODUCTS 4.5 F ....................22 EEDBACK AND UGGESTIONS 5 UPDATE ............................23 5.1 A ........................23 UTOMATIC PDATE 5.2 M ........................24 ANUAL PDATE 6 VCI MANAGER ..........................25 7 FIRMWARE UPDATE ........................27 NT710 User's Manual V1.1...
Page 8 11.4 M ........................56 ODULE ORTING 11.5 S ..........................58 ILES 11.6 R ........................58 EMOTE ONTROL 11.7 A .........................59 UTOMATIC PDATE 11.8 S ........................59 YSTEM ETTINGS 11.9 G ..........................59 ENERAL 11.10 U ..................... 59 NINSTALL EHICLE OFTWARE NT710 User's Manual V1.1...
Page 9 11.11 C ........................60 LEAR 11.12 P ........................60 RINT ETTINGS 11.13 A ...........................62 BOUT 12 REMOTE SUPPORT ........................63 NT710 User's Manual V1.1...
Page 10: Using This Manual
Bold text is used to highlight selectable items such as buttons and menu options. Example: Select Diagnostic from the Home screen of the NT710 application. 1.2 Symbols and Icons 1.2.1 Solid Spot Operation tips and lists that apply to specific tool are introduced by a solid spot.
Page 11: Introduction
Do not soak scanner as water might find its way into the scanner. 2 Introduction NT710 is newly developed diagnostic scanner with 5.5 inch TFT touch screen and Android 9.0 operating system that delivers OE-level diagnosis for different car brands and supports the most commonly required service and coding features.
Page 12: Accessories
2.2 Accessories This section lists the accessories that go with the scanner. If you find any of the following items missing from your package, contact your local dealer for assistance. NT710 User's Manual V1.1...
Page 13: Technical Specifications
Bluetooth specification v2.1+EDR; Bluetooth 4.0 Low Energy (LE) (10-20 m) 4000mAh, Lithium-polymer battery, chargeable via 5V USB Built-in Battery power supply ISO9141-2, ISO14230-2, ISO15765-4, K/L lines, Double K Line Protocols SAE-J1850 VPW,SAE-J1850PWM,CAN 11898, High-speed, Middle-speed, Lows-peed and Single wire CAN, NT710 User's Manual V1.1...
Page 14: Getting Started
3.1 Powering up the Scanner Before using the NT710 applications (including updating the scanner), please make sure to provide power to the scanner. The unit operates on any of the following sources: Internal Battery Pack ●...
Page 15: Screen Layout Of Home Screen
Diagnostic - leads to test screens for diagnostic trouble code information, ● freeze frame, live data and ECU information. Update - leads to screens for Foxwell ID registration and updating the ● scanner. Data Manager - leads to screens for saved screenshots, pictures and test ●...
Page 16: Diagnostic Menu
VCI Manager – VCI manage (VCI binding, unbinding, re-scan vehicle ● software). 3.3.2 Diagnostic Menu Touch Diagnostic at the NT710 application menu, and the Diagnostic menu will display. The operations of the buttons of Diagnostic menu are described in the below table. Figure 3-3 Sample Diagnostic Menu Screen...
Page 17: My Account
You are allowed to create a Foxwell ID with the built-in client. To register with built-in client: 1. Press My Account or Update from home screen of NT710 diagnostic application, the user login page will show, then press Free registration button to register an account.
Page 18 Figure 4-2 Sample Update Client Main Screen 2. Enter the User Name (use one of your existing mail addresses as user name), and press Send Code button for get a verification code, Foxwell will send a 4-digit verification code to the email you just entered.
Page 19: Sign In
Figure 4-6 Sample Product Activation Screen 4.2 Sign in Press My Account or Update from home screen of NT710 diagnostic application, the user login page will show, enter your FOXWELL ID and password, and press Sign in button to sign in.
Page 20: Product Activate
Figure 4-8 Sample Product Activation Screen 2.Click Submit to continue the activation and press to give up activation. Figure 4-9 Sample Product Activation Submit Screen 3. “Product is activated successfully” message will appear if activate successfully. NT710 User's Manual V1.1...
Page 21: M Yaccount
Figure 4-11 Sample My Account Screen 4.4 My Products This option let you activate a new product and manage activated products including serial number and expiration date. NT710 User's Manual V1.1...
Page 22: Feedback And Suggestions
This option allows you to log on your e-mail and send feedback and suggestions about Foxwell products. To send feedback and suggestions about Foxwell products: 1. Press My Account from home screen of the NT710 diagnostic application. 2. Press Feedback and Suggestions option to show Feedback page, there are two options--Diagnosis Feedback and General Feedback.
Page 23: Update
The scanner can be updated to keep you stay current with the latest development of diagnosis. This section illustrates how to register and update your scan tool. You can register both on Foxwell website or by the built-in update client.
Page 24: Manual Update
Figure 5-1 Sample Automatic Update Screen To automatic update or refer to 12.7 Automatic Update: 1. Press Settings from home screen of the NT710 diagnostic application. 2. Select Automatic Update, then set automatic update notice enable. 5.2 Manual Update To update the diagnostic application: 1.
Page 25: Vci Manager
VCI. VCI unbind & rebind： 1. Click VCI Manager application on the NT710 home screen. 2. After clicking Unbind a VCI dongle, it will display whether to unbind the current VCI. When clicking OK, it will execute unbind, rebind, and refresh the vehicle.
Page 26 Figure 6-2 Sample Unbinding Confirmation Prompt Figure 6-3 Sample Unbinding Current VCI Figure 6-4 Sample Bind New VCI Successfully Figure 6-5 Sample Rescan Vehicle Software NT710 User's Manual V1.1...
Page 27: Firmware Update
7 Firmware Update This application allows you to update the firmware of NT710. To update the firmware: 1. Click the Update application on the NT710 home screen. 2. Check and download the firmware package. 3. After the download is completed, it will automatically jump to the Firmware Update function module.
Page 28: Vehicle Identification
3. Connect a correct adapter to the data cable according to the vehicle being serviced and plug it into the vehicle DLC. 4. Switch the ignition key to the ON position. NT710 User's Manual V1.1...
Page 29: Vin Reading
(VIN). To identify a vehicle by Automatic Read: 1. Select Diagnostic from home screen of the NT710 application. 2. Click VIN and choose Automatic Read from the option list. 3. When the scan tool builds connection with the vehicle, the VIN number displays.
Page 30: Manual Entry
Manual Entry allows to identify a vehicle by inputting VIN manually. To identify a vehicle by Manual Entry: 1. Select Diagnostic from home screen of the NT710 application. 2. Click VIN and choose Manual Entry from the option list. 3. Press Keyboard button to input a valid VIN code and press OK to continue.
Page 31: Smart Vin
(VIN). To identify a vehicle by Smart VIN: 1. Select Diagnostic from home screen of the NT710 application. 2. A screen with vehicle manufacturers displays. Select the area where the vehicle manufacturer from. A menu of all vehicle manufacturers displays.
Page 32: Manual Vehicle Selection
VIN characters, such as model year, and engine type. To identify a vehicle by manual vehicle selection: 1. Select Diagnostic from home screen of the NT710 application. 2. A screen with vehicle manufacturers displays. Select the area where the vehicle manufacturer is from.
Page 33: Vehicle History
To identify a vehicle by Vehicle History: 1. Select Diagnostic from home screen of the NT710 application. 2. Select History button at the top of the diagnostic page and the diagnostic records will display.
Page 34: Vehicle Identification
(DTCs) overview. Depending on the number of control modules, it may take a few minutes to complete the test. To perform an automatic system scan: 1. Press Quick Scan option to start. 2. To pause the scan, press the Pause button on the screen. NT710 User's Manual V1.1...
Page 35 Figure 9-3 Sample Quick Scan Complete Screen 4. Press Report to create an overview of installed control units and their system status, or press Save to save the report. Press Erase to clear the information. Figure 9-4 Sample DTC Save Screen NT710 User's Manual V1.1...
Page 36: Control Modules
Control Modules displays all controllers available of the vehicle manufacturer. The controllers listed on the menu do not mean that they are installed on the vehicle. It is useful for technicians who are familiar with the vehicle specifications. NT710 User's Manual V1.1...
Page 37: Diagnostic Operations
● Clear Codes ● Live Data ● ECU Information ● NOTE Not all function options listed above are applicable to all vehicles. Available options may vary by the year, model, and make of the test vehicle. NT710 User's Manual V1.1...
Page 38: Read Codes
Frame button at the bottom bar. The screen will display freeze frame detail data, a snapshot of critical vehicle operating conditions automatically recorded by the on-board computer at the time of the DTC set. It is a good function to help determine what caused the fault. NT710 User's Manual V1.1...
Page 39: Clear Codes
To clear codes, make sure that the ignition key is switched to ON with the ● engine off. Clear Codes does not fix the problem that caused the fault! DTCs should ● only be erased after correcting the condition(s) that caused them. To clear codes: NT710 User's Manual V1.1...
Page 40: Live Data
All Data menu lets you view all live PID data from a selected control module. To view all live PID data: 1. Press Select ALL for select all live PID data and press Deselect ALL to deselect all items. NT710 User's Manual V1.1...
Page 41 Figure 9-16 Sample Live Data Selection Screen Figure 9-17 Sample Live Data Screen Name Description Help To provide help information of a PID To Top To move a data line to the top of Data List screen NT710 User's Manual V1.1...
Page 42 Figure 9-19 Sample Live Data Screen 3. Swipe the screen up and down to view additional information when necessary. NT710 User's Manual V1.1...
Page 43 Figure 9-21 Sample Multi-graphs Screen Merge Graph: merges multiple PID plots into one coordinate, so you can ● easily see how they affect each other, providing you with the most comprehensive and functional look at live data possible. NT710 User's Manual V1.1...
Page 44: Custom List
3. To deselect an item, tap the line again. Alternatively, tap SELECT ALL or Deselect ALL to select or deselect all items at once. 4. Press OK to complete the selection, and all selected items display. NT710 User's Manual V1.1...
Page 45: Record Data
1. Press Record button to record all selected live data, then it will show the record time and frames. Figure 9-25 Sample Live Data Record Screen 2. Press Stop button to create a record, then press OK to save the record into Data Playback of Data Manager. NT710 User's Manual V1.1...
Page 46: Ecu Information
Figure 9-28 Sample ECU Information Screen Press to print the information if need be. Press to exit. 4. Press Save to store ECU information screen and Press OK to complete save or Press Cancel to give up. NT710 User's Manual V1.1...
Page 47: Complaints
9.3 Complaints This function lets the customers sending back the complaints or feedback to Foxwell server with one touch during the diagnostic process and allows for quicker and more accurate fixes for diagnostic troubles and bugs. To make a complaint: Click during the diagnostic process when face a failure.
Page 48: Data Manager
Figure 9-31 Sample Compliant Sheet Screen 3.Press Upload to send to Foxwell server directly when connecting with Wifi or Press Save to save the complaint and send to us later.(The saved complaint can be found at Data Manager--Data Record menu.) Press Email to share or PDF to print.
Page 49: Image
10.1 Image Image option leads to screens for review of stored screenshots. In case a failure of NT710 application or the Android system occurs, please just take a screenshot and send it to our team to help with the troubleshooting.
Page 50: Review Image
Figure 10-4 Sample Screenshot Screen 10.1.2 Review Image To review the screenshots: 1. Press Data Manager from home screen of NT710 diagnostic application. 2. Press Image from Data Manager. 3. Press Diagnostic Screenshot for application menu screenshot or Press System Screenshot for system menu screenshot, then all available pictures will be displayed.
Page 51: Pdf Report
OK button to save. 10.2.1 How to Create a PDF Report To create a PDF report: 1. Press Data Manager from home screen of NT710 diagnostic application. 2. Press Report from Data Manager. 3. Press any reports saved. NT710 User's Manual V1.1...
Page 52: Review Pdf Report
Figure 10-10 Sample of Report edit Screen 10.2.2 Review PDF Report To review the PDF reports: 1. Press Data Manager from home screen of NT710 diagnostic application. 2. Press PDF and all available PDF files will be displayed. NT710 User's Manual V1.1...
Page 53: Data Playback
Playback speed and direction (forward or reverse) can also be controlled. To review recorded live data: 1. Press Data Manager from home screen of NT710 diagnostic application. 2. Press Data Playback and all available records display. NT710 User's Manual V1.1...
Page 54 Figure 10-15 Sample Graph Screen 5. To move forward or reverse back of the playing, just drag the progress bar forward or reverse. Press the button to stop. 6. Long press the record to Rename or Delete the records. NT710 User's Manual V1.1...
Page 55: Settings
Selecting Unit opens a dialog box that allows you to choose between Imperial customary or metric units of measure. To change the unit setup: 1. Press Settings from home screen of the NT710 diagnostic application. 2. Press Unit and available unit system display. 3. Select a unit system.
Page 56: Language
Select Language opens a screen that allows you to choose system language. To configure system language: 1. Press Settings from home screen of the NT710 diagnostic application and select Language. Then all available language options display. 2. Select your preferred language to change.
Page 57 Figure 11-3 Sample Drag the Data Manager module to the front of the Update module Figure 11-4 Sample Release and Dwell Data Manager Module 3. Click to display whether to apply the current settings interface, click OK to apply the current changes, click Cancel to discard the current changes. NT710 User's Manual V1.1...
Page 58: Sort Tiles
This option allows you to change the sort for Brand of vehicles. There are two sorting methods available by alphabet or by frequency of use. To change sort 1. Press Settings from home screen of the NT710 diagnostic application, and select Sort Tiles. 2. Select your preferred sort order.
Page 59: Automatic Update
1. Press Settings from home screen of the NT710 diagnostic application, then select Remote control. 2. Select your preferred tool. 11.7 Automatic Update This option allows you to enable/disable automatic update notice. If it is enabled, an orange update mark will show on the upper right of the diagnostic software icon whenever there is a new version available.
Page 60: Clear App Data
This option allows you to print any data or information anywhere and anytime either via PC network or Wi-Fi. To setup the printer connection: 1. Tap the Settings application on home screen of NT710. 2. Tap the Printing Settings option on the option list. Figure 11-9 Sample Print Settings Screen 3.
Page 61 Figure 11-11 Sample Setting of Print Service Manager Screen 5. Choose the right printer. Press for return. Figure 11-12 Sample of Printer Screen 6. Select a available printer, then press PRINT TEST PAGE button at the right-bottom. Press for return. NT710 User's Manual V1.1...
Page 62: About
Figure 11-14 Sample of File Printing Screen NOTE 1. Please make sure the printer and the NT710 in the same Wi-Fi or Network when printing. 2. If Mopria Print Service driver can’t workable for your printer, please download the driver to work for your printer on Print Service Manager.
Page 63: Remote Support
About how to set the tool of default, please refer to 11.6 Remote control. To use QuickSupport for to remote control: 1. Click the Remote Control icon on the main menu of the NT710 to start TeamViewer QuickSupport. Press for return.

Foxwell NT710 Manual

Quick Links

Need help?

Questions and answers

Related Manuals for Foxwell NT710

Summary of Contents for Foxwell NT710

Table of Contents