Subscribe to Our Youtube Channel
Related Manuals for Case CX470B
Summary of Contents for Case CX470B
- Page 1 CX470B Crawler Excavator SERVICE MANUAL Part number 48004716 English March 2016 © 2016 CNH Industrial Italia S.p.A. All Rights Reserved.
- Page 2 CRAWLER EXCAVATOR CX470B SERVICE MANUAL TABLE OF CONTENTS DIVISION/SECTION SECTION N° GENERAL INFORMATION Safety, general information and standard torque data..................1001 General specifications and special torque setting ....................1002 ENGINE Removal and installation of the engine.......................2000 Removal and installation of the fuel cooler, engine inter-cooler, radiator and oil cooler ............................2001...
- Page 3 DIVISION/SECTION SECTION N° UPPERSTRUCTURE HYDRAULICS Specifications, troubleshooting, checks and hydraulic pressure settings..........................8001 Removal and installation of the hydraulic reservoir ................... 8002 Removal and installation of the main hydraulic pump..................8003 Removal and installation of the main hydraulic control valve................8004 Removal and installation of the attachment cylinders..................
- Page 4 Section 1001 SAFETY, GENERAL INFORMATION AND TORQUE SPECIFICATIONS Copyright 2016 CNH France S.A. Printed in France March 2016...
- Page 5 Thanks very much for your reading, Want to get more information, Please click here, Then get the complete manual NOTE: If there is no response to click on the link above, please download the PDF document first, and then click on it. Have any questions please write to me: admin@servicemanualperfect.com...
-
Page 6: Table Of Contents
1001-2 TABLE OF CONTENTS GENERAL INFORMATION ............................. 3 SAFETY ................................... 4 STANDARD TORQUE DATA FOR CAP SCREWS AND NUTS ................6 ............................ 6 BOLT AND NUT TIGHTENING ..............................6 ORQUE TABLE Issued 03-16... -
Page 7: General Information
Parts Catalog for the correct par t to prevent early failures. number of the genuine Case replacement items. Fail- ures due to the use of other than genuine Case Bearings replacement parts are not covered by warranty. -
Page 8: Safety
Operator’s and Service WARNING: Read the operator’s manual to Manuals may be obtained from your Case familiarize yourself with the correct control dealer. functions. WARNING: If you wear clothing that is too... - Page 9 1001-5 WARNING: Use insulated gloves or mittens WARNING: When servicing or repairing the when working with hot parts. machine, keep the shop floor and operator’s compartment and steps free of oil, water, grease, tools, etc. Use an oil absorbing material and/or shop cloths as required. Use WARNING: Lower all attachments to the safe practices at all times.
-
Page 10: Standard Torque Data For Cap Screws And Nuts
1001-6 STANDARD TORQUE DATA FOR CAP SCREWS AND NUTS Bolt and nut tightening • Tighten alternating between left and right and top and bottom so that uniform tightening force is applied. • For bolts at critical locations, apply engine oil to the threads for a uniform tightening force without catching on the thread peaks. - Page 11 Section 1002 SPECIFICATIONS AND SPECIAL TORQUE SETTINGS Copyright 2016 CNH France S.A. Printed in France March 2016...
- Page 12 1002-2 TABLE OF CONTENTS WARNING: This symbol is used in this manual to indicate important safety messages. Whenever you see this symbol, carefully read the message which follows. Your safety depends on it. TYPE, SERIAL NUMBER AND YEAR OF MANUFACTURE OF THE MACHINE..................... 4 Machine ..................................
- Page 13 1002-3 Upper roller .................................30 Lower roller .................................32 Track shoe (grouser shoe)............................34 DIMENSIONS AND WEAR LIMITS OF ATTACHEMENT MOBILE JOINTS ..............35 1. Boom and frame installation section........................35 2. Boom cylinder and swing frame installation section ....................36 3. Boom and boom cylinder installation section......................36 4.
-
Page 14: Type, Serial Number And Year Of Manufacture Of The Machine
For all part orders, request for information or assistance, always specify the type and the serial number of the machine to your Case dealer. Fill in the following lines with the required information: Type, serial number, year of manufacture of the machine and the serial numbers of the hydraulic and mechanical components. -
Page 15: Fluids And Lubricants
CASE/AKCELA: HYDRAULIC EXCAVATOR FLUID (MS 1230. ISO VG 46. DIN 51524 PART 2 HV) Hot climates: 0°C to +50°C (32° to 122° F) CASE/AKCELA: AW HYDRAULIC FLUID 68 HV (MS 1216. ISO VG 68. DIN 51524 PART 3 CATEGORY HVLP) Cold climates: -25°C to +20°C (-13° to 68° F) CASE/AKCELA: AW HYDRAULIC FLUID 32 (MS 1216. -
Page 16: Engine Oil
1002-6 Engine Oil THE CASE/AKCELA No. 1 engine oil is recommended for your engine. This oil ensures proper lubrication of your engine for all operating conditions. If the CASE/AKCELA Multigrade "No. 1 ENGINE OIL" cannot be obtained, use the oil corresponding to one of the following categories: ACEA E7. -
Page 17: Engine Fuel, Maintenance Of Fuel Filters And Fuel Storage
1002-7 Engine fuel, maintenance of fuel filters and fuel storage In order to meet the emission control regulation of 3rd-stage, the engine components have been made precisely and they are to be used under high-pressure conditions. Therefore, the specified fuel must be used for the engine. As a matter of course, not only the guarantee will not be given for the use of a fuel other than the specified but also it may invite a serious breakdown. - Page 18 In this case, do not use these fuels because damage to the engine may result as the fuel has been contaminated. It is natural that the emission control regulation of 3rd-stage will not be cleared in case where a fuel that does not meet the specifications and the requirements is used.
-
Page 19: Anti-Freeze/Anti-Corrosion
Never throw oil or fluid on the ground and never place it in leaking receptacles. Contact your local ecological recycling centre or your CASE Dealer to obtain information on the correct method of dis- posing of these lubricants. -
Page 20: Main Equipment Layout
1002-10 MAIN EQUIPMENT LAYOUT Engine Front idler Boom cylinder Radiator Bucket Travel motor Control valve Tool box Boom Hydraulic pump Bucket cylinder Battery Hydraulic oil tank Air conditioner condenser Air cleaner Fuel tank Swing motor Arm cylinder Issued 03-16... -
Page 21: Consumable Part Layout
1002-11 CONSUMABLE PART LAYOUT Housing left side Pump chamber Air conditioner outside filter Washer tank Air cleaner Battery Reserve tank Pilot filter Fuel prefilter Issued 03-16...
Need help?
Do you have a question about the CX470B and is the answer not in the manual?
Questions and answers