Next POE2424SFP-380 Quick Installation And Initial Configuration

Next POE2424SFP-380 Quick Installation And Initial Configuration

Advertisement

Quick Links

www.ez-net.co.kr
NEXT-POE2424SFP-380
24Port 10/100/1000M + 2 GbE SFP
POE+ Switch
Quick Installation and
Initial Configuration
i

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the POE2424SFP-380 and is the answer not in the manual?

Questions and answers

Summary of Contents for Next POE2424SFP-380

  • Page 1 NEXT-POE2424SFP-380 24Port 10/100/1000M + 2 GbE SFP POE+ Switch Quick Installation and Initial Configuration...
  • Page 2: Table Of Contents

    www.ez-net.co.kr Contents Chapter 1 Introduction ............ 1 Overview ................1 Front View of the Switch ............ 1 Rear View of the Switch ............1 LED Descriptions ..............2 Mode/Reset Button ............4 Chapter 2 Installing the Switch ........5 Package Contents ............... 5 Mounting the Switch in a 19-inch Rack .......
  • Page 3: Chapter 1 Introduction

    Introduction Overview This user guide describes how to install, configure, and troubleshoot the NEXT-POE2424SFP-380, 26 Ports Unmanaged+GbE PoE+ Switch. By reading this user guide, users can perform the following tasks: To check the switch status by reading the LED behavior ...
  • Page 4: Led Descriptions

    www.ez-net.co.kr LED Descriptions The LEDs on the front panel provide users with switch status checking and monitoring. There are three types of LEDs as follows: System LED  indicates if the switch is powered up correctly or not, or, indicates if there is a system alarm triggered for troubleshooting.
  • Page 5 www.ez-net.co.kr The RJ45 Port Status LEDs are displayingPoE powering status of each port. By pressing the MODE button in less than 2 seconds to change LED modes (Link/Act/Speed Mode or PoE Mode), users can check the port status by reading the LED behaviors per the table below. Table 3:Port Status LEDs When Link/Act/Speed Mode LED Lit LED Color...
  • Page 6: Mode/Reset Button

    www.ez-net.co.kr The port has no active network cable connected, or it is not connected a PoE PD device. Otherwise, the port may have been disabled through the switch user interface. Mode/Reset Button By pressing the Mode/Reset Button for certain period of time, users can perform the following tasks.
  • Page 7: Chapter 2 Installing The Switch

    www.ez-net.co.kr Chapter 2 Installing the Switch Package Contents The Switch  AC Power cord (Option)  Four adhesive rubber feet  Installation Guide  Mounting kit(Option)  Note The switch is an indoor device. If it is to be used with outdoor devices such as outdoor IP cameras or outdoor WiFi APs, then users are strongly suggested to install a surge protector or surge suppressor in order to protect the switch.
  • Page 8: Mounting The Switch On Desk Or Shelf

    www.ez-net.co.kr Step2: Place the switch on a rack shelf in the rack. Push it in until the oval holes in the brackets align with the mounting holes in the rack posts. Step 3: Attach the brackets to the posts. Insert screws and tighten them. Figure 4:Attaching Brackets to the Rack Post Mounting the Switch on Desk or Shelf Step1:...
  • Page 9: Installing Sfp Modules

    www.ez-net.co.kr Step 3: Check the SYS LED. If it is ON, the power connection is correct. Figure 6:Connecting AC power cord Installing SFP Modules You can install or remove a mini-GBIC SFP module from a SFP portwithout having to power off the switch. Step1: Insert the module into the SFP port.
  • Page 10 www.ez-net.co.kr Chapter 3 Initial ConfigurationofSwitch Initial Switch Configuration Using Web Browsers After powering up the switch for the first time, you can perform the initial switch configuration using a web browser. For managing other switch features, please refer to the Web interface user guide for details. To begin with theinitial configuration stage, you need to reconfigure your PC’s IP address and subnet mask so as to make sure the PC can communicate with the switch.
  • Page 11: Chapter 4 Troubleshooting

    www.ez-net.co.kr Chapter 4 Troubleshooting The following table provides information for users to easily troubleshoot problems by taking actions based on the suggested solutions within. Table 5:Troubleshooting Table Possible Symptoms Suggested Solutions Causes 1. Check if correct power cord is connected firmly to the switch and to the AC outlet socket.
  • Page 12 제 품 보 증 서 24Port 10/100/1000M + 제 품 명 모 델 명 NEXT-POE2424SFP-380 2 GbE SFP POE+ Switch 구입일자 보증 기간 2년 고객성명 전 화 고객주소 판 매 점 전 화 판매점 주소 제조자 (주)이지넷유비쿼터스 전 화...

Table of Contents