Related Manuals for Next POE2429L2-370
Summary of Contents for Next POE2429L2-370
-
Page 1: Initial Configuration
NEXT-POE2429L2-370 Web Smart+ GbE PoE+ Switch Quick Installation and Initial Configuration... -
Page 2: Table Of Contents
Contents Chapter 1 Introduction ............ 1 Overview ................... 1 Front View of the Switch ............1 Rear View of the Switch .............. 1 LED Descriptions ................2 Mode/Reset Button ..............4 Chapter 2 Installing the Switch ........5 Package Contents ................. 5 Mounting the Switch in a 19-inch Rack ....... -
Page 3: Chapter 1 Introduction
Overview This user guide describes how to install, configure, and troubleshoot the NEXT-POE2429L2-370, 28 Ports Web Smart+ GbE PoE+ Switch. By reading this user guide, users can perform the following tasks: To check the switch status by reading the LED behavior ... -
Page 4: Led Descriptions
LED Descriptions The LEDs on the front panel provide users with switch status checking and monitoring. There are three types of LEDs as follows: System LED indicatesif the switch is powered up correctly or not, or, indicates if there is a system alarm triggered for troubleshooting. Mode LEDs ... - Page 5 By pressing the MODE button in less than 2 seconds to change LED modes (Link/Act/Speed Mode or PoE Mode), users can check the port status by reading the LED behaviors per the table below. Table 3:Port Status LEDs When Link/Act/Speed Mode LED Lit LED Color State Description...
-
Page 6: Mode/Reset Button
Mode/Reset Button By pressing the Mode/Reset Button for certain period of time, users can perform the following tasks. Change Port Status LED Mode to read the port status correctly in the twodifferent modes (Link/Act/Speed mode or PoE mode). Reset the Switch ... -
Page 7: Chapter 2 Installing The Switch
Chapter 2 Installing the Switch Package Contents The Switch AC Power cord (Option) Four adhesive rubber feet Installation Guide Mounting kit(Option) Note The switch is an indoor device. If it is to be used with outdoor devices such as outdoor IP cameras or outdoor WiFi APs, then users are strongly suggested to install a surge protector or surge suppressor in order to protect the switch. -
Page 8: Mounting The Switch On Desk Or Shelf
Step2: Place the switch on a rack shelf in the rack. Push it in until the oval holes in the brackets align with the mounting holes in the rack posts. Step 3: Attach the brackets to the posts. Insert screws and tighten them. Figure 4:Attaching Brackets to the Rack Post Mounting the Switch on Desk or Shelf Step1:... -
Page 9: Connecting The Ac Power Cord
Connecting the AC Power Cord Step 1: Connect the AC power cord to the AC power receptacle of switch. Step 2: Connect the other end of the AC power cord to the AC power outlet. Step 3: Check the SYS LED. If it is ON, the power connection is correct. Figure 6:Connecting AC power cord Installing SFP Modules You can install or remove a mini-GBIC SFP module from a SFP port... - Page 10 Figure 7:Installing a SFP Module into a SFP Port Note The SFP ports should use UL Listed Optional Transceiver product, Rated 3.3Vdc, Laser Class 1.
-
Page 11: Chapter 3 Initial Configurationofswitch
Chapter 3 Initial ConfigurationofSwitch Initial Switch Configuration Using Web Browsers After powering up the switch for the first time, you can perform the initial switch configuration using a web browser. For managing other switch features, please refer to the Web interface user guide for details. To begin with theinitial configuration stage, you need to reconfigure your PC’s IP address and subnet mask so as to make sure the PC can communicate with the switch. - Page 12 Step 2: Select Network and Sharing Center Step 3: Click on Change adapter settings on the left of PC screen Note Users can also skip step 1 to 3, by pressing WinKey+R and type ”ncpa.cpl”command to get to step 4 directly. Step 4:Right-click on your local adapter and select Properties Step...
- Page 13 If your PC is configured correctly, you will see the login page of the switch as shown by Figure 9 below. Figure 8:Web Interface login page If you do not see the above login page, please perform the following steps: - Refresh the web page.
-
Page 14: Chapter 4 Troubleshooting
Chapter 4 Troubleshooting The following table provides information for users to easily troubleshoot problems by taking actions based on the suggested solutions within. Table 5:Troubleshooting Table Possible Symptoms Suggested Solutions Causes 1. Check if correct power cord is connected firmly to the switch and to the AC outlet socket. - Page 15 제 품 보 증 서 24-Port 10/100/1000T POE + 4-Port 1000X SFP 제 품 명 모 델 명 NEXT-POE2429L2-370 Gigabit Managed Web Smart Switch / 370W 구입일자 보증 기간 2년 고객성명 전 화 고객주소 판 매 점 전 화 판매점 주소...
Need help?
Do you have a question about the POE2429L2-370 and is the answer not in the manual?
Questions and answers