Leviton Decora IllumaTech RTF01-10X Installation Instructions

WARNINGS AND CAUTIONS:
• To be installed and/or used in accordance with appropriate electrical codes and regulations.
• If you are unsure about any part of these instructions, consult a qualified electrician.
• To avoid overheating and possible damage to this device and other equipment, do not install to
control a receptacle, fluorescent lighting, a motor- or a transformer-operated appliance other than
appropriate ceiling fans.
• To reduce the risk of fire or electrical shock, this control is to be used with ceiling fans that are rated
120VAC, total load 1.5 amperes maximum.
Tools needed to install your Fan Speed Control:
Slotted/Phillips Screwdriver Electrical Tape
Pliers Pencil
Cutters Ruler
Color Change Option:
If a color change kit is provided with your device, proceed with the
following step if you need to change the color. Otherwise, proceed with
the "Installing Fan Speed Control by itself or with other devices"
section.
CHANGING THE COLOR OF YOUR FAN SPEED
CONTROL
Your Fan Speed Control includes two color options. The Control ships with
the White frame attached. To change color of frame, proceed as follows:
Push in side at tab
to release. Remove
frame and knob.
Installing Fan Speed Control by itself or with other
devices
If installing Control in a single device application, proceed with the
MULTI-FAN CONTROL section. If installing Control in a multi-device
application, proceed as follows:
MULTI-DEVICE APPLICATION
NOTE: There is NO derating necessary for multi-gang installations of
this Fan Speed Control.
Quiet Fan Speed Control - Single Pole (One location)
INSTALLATION INSTRUCTIONS
MULTI-FAN CONTROL
Any number of fans of the same type may be controlled by a single fan
speed control provided that the total amperage of the fans do not
exceed the amperage of the fan speed control.
INSTALLING YOUR FAN SPEED CONTROL
NOTE: Use check boxes
WARNING:
Step 1
POWER at circuit breaker or fuse and test that power is off
before wiring!
OFF
OFF
OFF
OFF
OFF
OFF
Removing existing switch:
Step 2
wallplate and switch mounting screws. Carefully pull switch
from wall box. DO NOT remove wires attached to the switch
at this time.
Press on knob. Line up
Identifying your wiring application (most
Step 3
tabs on back of frame and
common):
press in side to attach
NOTE: If the wiring in the wall box does not resemble this
single pole configuration, consult a qualified electrician.
Single-Pole:
Look at the back of your switch. There should be 2 wires connected to
two screw terminals (not including a green or bare copper wire used for
grounding), you have a Single-Pole switch.
Fan Speed Control
Cat. No. RTFØ1-1Ø
Rated: 1.5A-120VAC, 60Hz
WARNINGS AND CAUTIONS:
• For use on ceiling paddle fans with split-capacitor or shaded pole motors only. Please refer to
manufacture's instructions or rating label on the motor to confirm type. Use with any other types of
motors or equipment may cause overheating and/or damage to the motors or equipment.
• Disconnect power at circuit breaker or fuse when servicing fixture.
• Use this device only with copper or copper clad wire. With aluminum wire use only devices marked
CO/ALR or CU/AL.
√
when Steps are completed.
To avoid fire, shock, or death; TURN OFF
OFF ON
ON
OFF ON
ON
ON OFF ON
OFF ON
ON
ON OFF ON
ON OFF ON
Remove existing
Disconnecting switch wires and preparing wires:
Step 4
• Disconnect wires from screw terminals or
Quickwire™ slots (shown).
• Pull off pre-cut insulation from Control
leads.
• Make sure that the ends of the wires from
the wall box are straight (cut if
necessary).
• Remove 5/8" (1.6 cm) of insulation from
each wire in the wall box (shown).
Cut
Press in slot and
(if necessary)
pull out wire
Single-Pole Wiring Application:
Step 5
Black
Neutral
Green
Ground
Red
DI-000-RTF01-02C
Strip 5/8"
(1.6 cm)
5/8"
(1.6 cm)
Strip Gage
Electrical
Tape
Insert wires
straight then twist
clockwise