Related Manuals for SealerSales W-300DAT
Summary of Contents for SealerSales W-300DAT
- Page 1 Table-Top Direct Heat Sealers Models: W-300DAT, W-300DATS Distributed By: Version 1.0_2014...
-
Page 2: General Information
General Information Thank you for purchasing our W-Series Direct Heat Sealers. This owner’s manual contains information relating to your sealer. The manual will provide you with basic information concerning both operation and maintenance of your new machine. Please read it carefully as failure to do so may result in bodily injury and/or damage to the equipment. Please fill in the information below. -
Page 3: Safety Instructions
W H D H W H D H I N S T R U C T I O N I N S T R U C T I O N M A N M A N U A L Safety Instructions Safety Instructions WARNING! WARNING! - Page 4 W H D H I N S T R U C T I O N M A N U A L Never touch the sealing bars with your bare hands while the sealer is plugged into a power source, in operation or just finished operation.
- Page 5 Hands free sealing activated by footswitch Sealing width: 1/2" (15mm) Sealing length: 12" (300mm) Adjustable work table Options: meshed (W-300DAT) or serrated (W-300DATS) sealing bars Figure 2. Serrated seal line Figure 1. Meshed seal line...
-
Page 6: Specifications
The operator places material on lower sealing bar of sealer and activates foot switch to bring the upper sealing bar down. Upper sealing bar will release automatically based on timer settings. Specifications W-300DAT W-300DATS Power 110V/60Hz 110V/60Hz... - Page 7 Getting to Know your Direct Heat Sealer T em per a t ur eCont r ol l er P r otec torBa r s Adjust temperature Bars protect operator P ow erS w i tc h depending on material from the sealing bars Turn on when you are to be sealed (0˚C-300˚C) ready to use your sealer...
-
Page 8: Electrical Circuit Diagram
Electrical Circuit Diagram Figure 4. Electrical Circuit Diagram for W-Series Direct Heat Sealers... -
Page 9: Operation
Operating your Operating your Sealer Assembly Instructions Assembly Instructions 1. Connect the footswitch to the sealer unit. Connect the footswitch to the sealer unit. 2. To install the optional working plate and table optional working plate and table, remove screws located at the front of the unit and at the front of the unit and install the working plate. - Page 10 7. When sealer is not in use, turn off the power switch When sealer is not in use, turn off the power switch. Please note: Sealing bars will be extremely hot. Do not touch the Please note: Sealing bars will be extremely hot. Do not touch the sealing bars as this could cause severe burns.
-
Page 11: Maintenance
Maintenance The following maintenance procedures should be followed to ensure the longevity of your The following maintenance procedures should be followed to ensure the longevity of your The following maintenance procedures should be followed to ensure the longevity of your W-Series Direct Heat Sealer. - Page 12 Replacing Heater (s) Our W-Series Direct Heat Sealers will require new heaters from time to time. There are two heaters found on the unit, one in the upper sealing jaw and one in the lower sealing jaw. Remove the old heater on either the top and/or bottom sealing jaw. Unscrew the heater loose from the sealing jaw and base of sealer.
- Page 13 3. Unscrew the heaters from the bottom sealing jaw in order to remove the thermostat sensor from the sealing jaw. Note: In order to fully remove and install the thermostat, one may also need to separate the head of the sealer from the base. Figure 11.
-
Page 14: Parts Diagram
Parts Diagram Figure 14. Spare Parts Diagram Overview... - Page 15 WHDH-3B PTFE Coated Sealing Bar, Pair Coated, Serrated WHDH-5 Rubber Foot WHDF-6 Pressing Spring, Small W-00403 W-300T-12 Pressing Spring, Large (W-300T and W-300DAT) TMC-WHDH Thermostats (E.G.O) E-010 WHLH-7 Power Switch, 3P, 15A/125V (W-Series) WHI-11a Circuit Breaker, 7A, W-350I and W-300DAT(S)
-
Page 16: Troubleshooting
Troubleshooting Problem Possible Causes Solution Upper and/or lower sealing bars 1. Heater(s) are worn out. 1. Replace heaters(s) on the unit. not heating Unit does not heat up (both jaws are 1. Heater(s) are worn out. 1. Replace heaters(s) on the unit. not heating up) 2.
Need help?
Do you have a question about the W-300DAT and is the answer not in the manual?
Questions and answers