Contents I Use ……………………………………………………………1 II Safety Instructions ………………………………………1 III Specifications ………………………………………………2 IV Performance Features…………………………………3 V Structure & Working Principle…………………………4 VI Operation Instruction……………………………………6 VII Circuit Diagram …………………………………………13 VIII Breakdown Drawing of Machine………………………14 IX Troubleshooting……………………………………………30...
I. Use This sealer is suitable for sealing all kinds of plastic films, which is widely used in fields of food, medicine, chemicals, daily use and vegetable seeds etc. It is the best sealing equipment for packing batch products from factories and shops. II.
III. Specifications Model FRM-1120LD FR-1370LD Parameter Solid-ink coding continuous band Continuous band sealer sealer Item Voltage AC 220/50 110/60 Motor power 245W Sealing power 300×2W 300×4W Printing power 40×2W Sealing speed 0~10m/min Sealing width 10mm 0~300(℃) (Stepless adjustable) Temperature control range...
3. FRM-1120LD series can use solid-ink roller to print desired colored label while sealing, with the characteristics of high definition, instant print, instant dry and strong adhesion;...
V. Structure & Working Principle 1. This machine is made up of machine frame, speed-adjusting mechanism, sealing temperature control system, transmission and conveying system, and printing assembly etc (see Diagram 1-Diagram 2). FRM-1120W Solid–ink coding continuous band sealer Diagram 1 1.
Page 6
FR-1370LD Continuous band sealer with two sets of heating blocks Diagram 2 2. After the power supply being connected, the heating element produces heat that rapidly raise the temperature of both upper and lower heat blocks. By using the temperature controller and speed-adjusting mechanism, adjust it to the needed temperature and speed.
VI. Operation Instruction 1. Control Panel (See Diagram 3) FRM-1120LD Diagram 3 FR-1370LD Diagram 4 2. Prepare the machine for use 1) This machine is equipped with a three-pin crust-grounded socket. Please check if it is well connected so as to ensure safe operation.
Page 8
approximately equal to the thickness of packing bag in one layer. The firmness of sealing and high definition of embossing shall be guaranteed, also suitable length extended from two ends of sealing part shall be ensured. 3. Ways of replacing and adjusting the sealing belt: 1) Remove the safety cover, when heating blocks become cooled, rotate retaining washer in the upper heating block and lower cooling blocks by 30 degrees, and lift these two sections.
Page 9
4. The selection of the type arrange way: The type in longitude arrange is R arrange, while types in axial arrange is T arrange (see Diagram 6). T arrange R arrange Diagram 6 (This manual introduces the solid-ink roller coding mechanism which is controlled by electromagnetic clutch intermittent mechanism.
Page 10
6.set screw of printing wheel; 7.printing wheel Diagram 7 2) The adjustment of the clearance between ink roller and types: Adjust the adjusting screw (5) for the ink roller’s swing pole, rotate the printing wheel, and make the types’ surface touch the ink roller’s (1) surface slightly. If the ink roller can be easily driven by rotating the printing wheel with hand, it should be ok (see Diagram 8).
Page 11
1.printing wheel; 2.silicone wheel; 3.eccentric sleeve; 4.screw Diagram 9 4) Temperature adjustment for printing wheel and ink roller: All the knobs of this machine are set to position 0 before leaving factory. Users need to make adjustment by themselves. For a new ink roller, during previous time of using, the temperature should be relatively lower, after a period time of using, the temperature can be raised to higher degree, which can make the deep-seated ink ooze and prolong the ink roller’s life-span.
Page 12
6. Adjustment of coding position: Users can locate the coding position by adjusting coding position knob according to the length of bag opening. 7. Adjustment of number of lines in printing label: Arrange types within stipulated range, and then use the provided silicone bar to fix the types in required axial position.
Page 13
left end of the slot. Then remove screw (1) (total 6 pcs), loosen screw (3) (front two pcs) to drag off the front baseplate (6) and motor safety cover(4). At this point, the conveyor belt is in a fully loosened state and finally unload conveyor belt.
VIII. Breakdown Drawing of Machine Body 1. Main Body (Part 1) Picture 1 Code Description Quantity Remark Base Plate Bearing Seat Spacer Deep Groove Ball Bearing 6201-2RS Circlip for Hole Ф32mm Driving Wheel Shaft Driving Wheel Flat Washer (Ф5×Ф28×2) Guiding Belt 678×4.5×3.5 Copper Block Pad 1-10...
IX. Troubleshooting Problem Reason Solution Fail to work Power supply disconnected Check the power socket Fuse broken or Circuit breaker Replace fuse or circuit breaker tripped Reset the Emergency Switch Emergency Switch fail to reset after being Pressed Sealing belt Driving wheel shaft is not parallel to driven Adjust two adjusting screws on driven off-tracking.
Page 32
Problem Reason Solution 1. Check whether the power line is 1. The power supply is not connected. connected and indicating light is on. roller printing 2. Main control PC board is not 2. Check whether plug for PC board is mechanism doesn’t work inserted in place or poor contact.
Page 33
▲ Motor maintenance 1. Stop machine when any abnormal occurs to motor, continue to use till problem solved. 2. Dedust and clean motor at regular intervals. Alcohol, gasoline and liquid with benzene chemicals should be avoid using, otherwise affecting paint of motor cover 3.
Need help?
Do you have a question about the FRM-1120LD and is the answer not in the manual?
Questions and answers