Advertisement
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Gemtek WLTGG-122
Summary of Contents for Gemtek WLTGG-122
- Page 1 LTE CPE Quick installation Guide WLTGG-122 LTE Outdoor CPE...
-
Page 2: Table Of Contents
Contents CONTENTS ............1 1. CONNECTORS ..........2 2. LED INDICATORS .......... 3 3. INSTALLING LTE OUTDOOR CPE ....4 4. CONNECTING THE CABLES ......7 5. WEB INTERFACE ........... 9... -
Page 3: Connectors
Connectors 1. One RJ-45 connector for connecting to the PoE adaptor. 2. LED indicator inside and SIM card slot for inserting SIM card. GPS Antenna (The GPS function is optional. It will activated base on the different SW customization) 4. A grounding screw on the rear panel. -
Page 4: Led Indicators
LED Indicators LED name Location Color LED Behavior Status Indication LED List ●●● ●●●●● MAIN power Blue Power On ●○○ ○○○○○ Power Off Ethernet Orange Detect Ethernet ○●○ Steady ON status Device Connected ○○○○○ Blinking No Ethernet connection SIM status Green ○○●... -
Page 5: Installing Lte Outdoor Cpe
Installing LTE outdoor CPE Selecting a Location: LTE Outdoor CPE should be pole-mounted outdoors and aligned so its antenna faces the nearest LTE eNB. When selecting a suitable location for the unit, consider these guidelines: Place LTE Outdoor CPE as high as possible to achieve the best •... - Page 6 [ With 16dBi antenna ] Using the clamp [adjustable angle] • 1. Thread the M10*20mm bolt through a spring washer, flat washer and the bracket holes, and tighten the bolts to the LTE Outdoor CPE. 2. Thread the M10*100mm bolt through a spring washer, flat washer and the holes of bracket A.
- Page 7 3. With the connector facing downward, and assembling two brackets together. Thread the M10*20mm bolt through a spring washer, flat washer and the bracket holes. 4. Adjust the required angle and lock the screws.This is an angle that can be adjusted 10 degrees above and below. [ With 13dBi antenna ] [ With 16dBi antenna ]...
-
Page 8: Connecting The Cables
Connecting the Cables Outdoor Connection: Connect a grounding cable between the Ground terminal of the LTE outdoor CPE and a good ground connection. Preparing and connecting the cable: Use only 5E 4x2x24# FTP (or from an approved manufacturer. above) outdoor Shielded Patch Cable 1. - Page 9 the gland base from the bracket. • Insert the cable into the sealing gland base and connect it to the RJ-45 connector at the bottom of the CPE. Make sure the connector is completely inserted and tightened. • Insert the rubber bushing on the cable into the gland base. •...
-
Page 10: Web Interface
Web Interface Please follow the steps below to configure your device through the web interface: Open the Web browser (Internet Explorer) and enter the default IP Step1: address of the ODU CPE, which is : http://192.168.15.1 Enter ODU administrator login username/password to access the Step2: web management interface. - Page 11 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
- Page 12 RF exposure requirement. 3. External antenna Use only the antennas which have been approved by Gemtek, BLiNQ. The non-approved antenna(s) may produce unwanted spurious or excessive RF transmitting power which may lead to the violation of FCC limit and is prohibited.
Need help?
Do you have a question about the WLTGG-122 and is the answer not in the manual?
Questions and answers