Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for SmartRG DB120-WL
Summary of Contents for SmartRG DB120-WL
- Page 1 ４ PORTS ＋ WIRELESS ADSL2+ Router DB120-WL User Manual V 1.１...
-
Page 2: Table Of Contents
DSL Gateway/Router — User Manual CONTENTS 1.OVERVIEW............................... 3 1.1 ABOUT ADSL ............................. 3 1.2 ABOUT ADSL2/2+ ..........................3 1.3 FEATURES ............................3 2 SPECIFICATION.............................. 4 2.1 INTERFACE INTRODUCTION ......................4 2.1.1 INDICATOR AND INTERFACE....................4 2.1.2 SPLITTER SPEC .......................... 4 2.2 HARDWARE CONNECTION...................... -
Page 3: Overview
DSL Gateway/Router — User Manual 1.OVERVIEW 1.1 ABOUT ADSL An ADSL MODEM is a broadband Internet access device, which utilizes the high frequency segment of the phone line to transmit high-speed data without affecting the voice transmission. The frequency of the ADSL signal is higher than that of voice, so voice and ADSL signal can coexist in one line by using a splitter to insulate each from the other. -
Page 4: Specification
DSL Gateway/Router — User Manual 2 SPECIFICATION 2.1 INTERFACE INTRODUCTION 2.1.1 INDICATOR AND INTERFACE Table 2.1 ITEM Name State introduction POWER A steady red light means the power connection works properly Yellow, shows DSL line status. Indicator INTERNET Green, Flashing means the Modem is transmitting or receiving data WLAN Green, Indicates status of connection to the wireless device Connected with phone line or “ADSL”... -
Page 5: Hardware Connection
DSL Gateway/Router — User Manual 2.2 HARDWARE CONNECTION Introduction： 1、 Use a telephone cord to connect the LINE port of the splitter with the RJ-11 port (the phone jack) on the wall. 2、 Use another telephone cord to connect the ADSL port of the splitter with the LINE port of the ADSL Modem. -
Page 6: Configuration
DSL Gateway/Router — User Manual 3. CONFIGURATION 3.1 DEFAULT CONFIGURATION ADSL MODEM has pre-configured with the VCI/VPI which is in common use. The default dial-up mode is bridge encapsulation. For bridge mode, no need to configure any more parameter. However, the third party dial-up software is needed for connection with the Internet. -
Page 7: Wan Configuration
DSL Gateway/Router — User Manual Note ： When you save the settings, the web page will be refreshed slowly, please wait it finished. After you save the settings, it will take effect until next reboot. Some settings only take effect after rebooting the router. 3.4 WAN CONFIGURATION If the configuration is bridge encapsulation, there is no need to configure any more parameters. - Page 8 DSL Gateway/Router — User Manual Figure 3.3 The value for VPI/VCI is assigned by your ISP. After inputting the PVC value, press “Next” into “connection type”. As Figure 3.4. Figure 3.4 The Modem supports five ADSL protocol modes. Choose the protocol which is appointed by ISP and PVC encapsulation, click “Next”...
-
Page 9: Rfc1483 Bridge Configuration
DSL Gateway/Router — User Manual 3.4.2 RFC1483 BRIDGE CONFIGURATION Select the Bridging mode. Then press “Next” to specify the Service Name, and select the “Enable Service” as Figure 3.5. Figure 3.5 Press “Next” to enter into “WAN configuration”, click “save” to save configuration, if you need to modify the parameter, click “back”... - Page 10 DSL Gateway/Router — User Manual Figure 3.7 Page 10 Total 20 Pages...
-
Page 11: Pppoe Configuration
DSL Gateway/Router — User Manual 3.4.3 PPPOE CONFIGURATION PPPoE is also known as RFC 2516. It is a method of encapsulating PPP packets over Ethernet. PPPoA is also known as RFC2364 and named as Peer to Peer Protocol over ATM. As PPPoE, it also has all the features of PPP. -
Page 12: Static Address
DSL Gateway/Router — User Manual disconnected. Press “Next step” when configuration is finished. The following operation is same with Figure 3.5. Notice that PPPoE mode does not work until the modem is reset. 3.4.4 STATIC ADDRESS In Figure3.4, select MAC Encapsulation Routing (MER), press “Next”, and the configuration can be queried from your ISP, the result as Figure3.9. -
Page 13: Wireless Configuration
DSL Gateway/Router — User Manual 3.5 WIRELESS CONFIGURATION Press “Wireless” on the top of web pages to enter wireless section. You can select to configure wireless setup, security and management. 3.5.1 WIRELESS SETUP Click “Setup” on the left menu to setup basic wireless parameters. In default, check “Enable Ｗireless” box to launch wireless AP. - Page 14 DSL Gateway/Router — User Manual Encryption Strength: Key length: 128bits or 64bits. Network Key 1-4: Up to four keys that are in form of hex digitals could be set. Mobile users can’t access the AP if they haven’t set the same key as AP. For 64bits and 128bits keys, you should input 10 and 26 hexadecimal digitals or 5 and 13 ASCII characters respectively.
-
Page 15: Wireless Mac Filter
DSL Gateway/Router — User Manual 3.5.3 WIRELESS MAC FILTER In fact, the Access List function is just like MAC address filtering and selected to permit or forbid access of wireless station with specified MAC address. Method: select “Allow” or “Deny” mode, and click “Add” button, and input MAC address which you want to allow or deny. -
Page 16: Other Configuration
DSL Gateway/Router — User Manual 4 OTHER CONFIGURATION 4.1 LAN CONFIGURATION Configuration of Modem’s IP address and password 4.1.1 CONFIGURATION OF MODEM’S IP ADDRESS As a network device, ADSL Modem has its own IP address and MAC address. The factory sets the MODEM, at a default IP address of 192.168.1.1 and subnet mask of 255.255.255.0. -
Page 17: Dhcp Configuration
DSL Gateway/Router — User Manual 4.1.2 DHCP CONFIGURATION • click“LAN ” • click“DHCP server” ； • Define the “Start IP address” and the “End IP address” of DHCP server (for example, from 10.10.10.11 to 10.10.10.254). • Input the value of lease (Measured by the second, 0 indicates permanently valid). As Figure 4.2, open DHCP server, computer will set the IP Address of network card with one of the address 10.10.10.11 ～... -
Page 18: Troubleshooting
DSL Gateway/Router — User Manual 5. TROUBLESHOOTING 5.1 UNABLE TO ACCESS INTERNET 5.1.1 CHECK THE LINE AND THE DEVICE 1、 Check the indicator of power supply is on, if not, Make sure the connection of power supply is correct; Make sure the output of power supply is correct; Make sure the switch of power supply is turned on； 2、... -
Page 19: Annex：shipping List
DSL Gateway/Router — User Manual subsequently popped up is the command line window. Note 3：The returned values of ping command in the following format show the standard of “reachable” Figure 5.1 6、 If ping of the modem is reachable but ping of the outer fixed IP is unreachable, attention should be concentrated upon device settings. - Page 20 DSL Gateway/Router — User Manual FCC INFORMATION This equipment complies with CFR 47, Part 15.19 of the FCC rules. Operation of the equipment is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received; including interference that may cause undesired operation.
Need help?
Do you have a question about the DB120-WL and is the answer not in the manual?
Questions and answers