Table of Contents
Advertisement
Quick Links
Please read the instructions completely before beginning the installation.
Vantage I Collection
Model Number: 2920EY-TM
Vantage Crystal I Collection
Model Number: 2920EC-TM
Flush both supply lines before installation, then shut off both supply lines.
Minimum hole size for the spout and handle trim is 1-1/4" and maximum of 1-1/2"
SPOUT INSTALLATION
- Remove the tee connector, spout mounting hardware and tee
1
connector washer from the bottom of the spout assembly. Apply
a ring of silicon caulking around the center hole on the top of the sink.
Do not use plumbers' putty which can damage the finish of the faucet.
- From the top of the deck, insert the spout's threaded shank through
the center hole of the sink. Make sure the spout flange washer is
properly placed underneath of the flange and gently pressed against
the sink top.
The measurements shown are for reference only. Products and specifications shown are subject to change without notice.
www.santecfaucet.com | P: 310.542.0063 F: 310.542.5681
Vantage II Collection
Model Number: 2920ET-TM
Rev 06/2016
Installation Instruction
VANTAGE COLLECTIONS
Widespread Lavatory Set
Rubber washer
1/8
Advertisement
Table of Contents
Related Manuals for Santec Vantage I 2920EY-TM
Summary of Contents for Santec Vantage I 2920EY-TM
- Page 1 Rev 06/2016 Installation Instruction VANTAGE COLLECTIONS Widespread Lavatory Set Please read the instructions completely before beginning the installation. Vantage I Collection Vantage II Collection Model Number: 2920EY-TM Model Number: 2920ET-TM Vantage Crystal I Collection Model Number: 2920EC-TM Flush both supply lines before installation, then shut off both supply lines. Minimum hole size for the spout and handle trim is 1-1/4”...
- Page 2 - Slip the spout mounting hardware back onto the spout. First the notched rubber washer, then the notched metal washer and lastly the brass lock nut. Hand tighten the lock nut. - Place the pop-up lift rod with the knob through the back hole in the spout and rotate the notched washers until the lift rod passes through the notch.
-
Page 3: Complete Assembly
COMPLETE ASSEMBLY INLET HOSE INLET HOSE TO THE HOT SUPPLY LINE TO THE COLD SUPPLY LINE The measurements shown are for reference only. Products and specifications shown are subject to change without notice. www.santecfaucet.com | P: 310.542.0063 F: 310.542.5681... - Page 4 POP-UP INSTALLATION Remove the decorative drain flange, drain plug and gasket from pop-up assembly. Do not remove the washer and lock nut. Place the flange gasket onto the drain tube beveled side upward and on top of the washer. Apply a ring of silicon caulking around the top of sink drain opening.
-
Page 5: Parts Drawing
PARTS DRAWING PART DESCRIPTION PART # PART DESCRIPTION PART # Vantage Tall W. Spout Head & Tube PS-2VT00-U-8 Vantage Widespread Bell PA3021 Washer PM-184 PM-473 Shank K-2500 Insert Stem for E/S SA240 Spout Mounting Hardware Assembly P0431 Screw PM-181 T-Connector P0427 Teflon Washer for Insert PM-099... -
Page 6: Specification Sheets
SPECIFICATION SHEETS 2" 2 " 4 7 8 " 13 1 3" " 2" 4 " " POP-UP Ø 2 " " " 12" Ø 1 " The measurements shown are for reference only. Products and specifications shown are subject to change without notice. www.santecfaucet.com | P: 310.542.0063 F: 310.542.5681... -
Page 7: To Obtain Warranty Service
Doing so may ruin your faucet finish and/or void the warranty. Thank you for making SANTEC a part of your lifestyle and luxury spa experience. Our products have been created as works of enduring quality and sophisticated design. -
Page 8: Lifetime Limited Warranty
SANTEC reserves the product components of the covered product will be repaired, refinished, or replaced at the sole discretion of SANTEC. SANTEC reserves the right to examine any product claimed defective prior to any warranty claim being accepted or processed, at its sole discretion. This warranty gives you specific legal rights and you may have other rights which may vary from state to state.