Monogram ZDIS15 Design Manual With Installation Instructions
Automatic ice maker
Hide thumbs
Also See for ZDIS15:
- Installation instructions manual (12 pages) ,
- Owner's manual (16 pages)
Subscribe to Our Youtube Channel
Related Manuals for Monogram ZDIS15
Summary of Contents for Monogram ZDIS15
- Page 1 Installation Instructions Automatic Ice maker ZDIC150 ZDIS15 Design Guide With Installation Instructions monogram.com...
-
Page 2: Table Of Contents
In the absence of local codes, the ice maker should be installed in accordance with National Electrical Code ANSI/NFPA 70-1990 or latest edition. For Monogram local service in your area, call 1.800.444.1845. For Monogram Service in Canada, call 1.800.561.3344. -
Page 3: Design Information
Design Information MODELS AVAILABLE ZDIS150HSSLH, ZDIS150HSSRH, and ZDIC150HBB The ice maker may be installed below a countertop Available in black and stainless steel. or used free-standing. OPTIONAL ACCESSORIES For the installation of a trimless ZPK2 Drain Pump Kit - For use when a floor drain is 3/4”... -
Page 4: Cutout & Product Dimensions
Installation Instructions ADVANCE PLANNING CUTOUT & PRODUCT DIMENSIONS (Cont.) CAUTION: Cutout dimensions shown allow for a full door swing. Due to excessive weight, TWO PEOPLE ARE REQUIRED TO MOVE AND INSTALL THIS Flush Installation, Top View Ice maker. Failure to do so can result in back or other injury. -
Page 5: Water Supply
Installation Instructions ADVANCE PLANNING (cont.) ADVANCE PLANNING (cont.) IMPORTANT: LOCATION REQUIREMENTS: This unit must NOT be on a GFCI (Ground Fault Circuit Interrupter) equipped outlet • Not designed for outdoor installation. or nuisance tripping may occur resulting in loss of •... -
Page 6: Power Supply
Installation Instructions POWER SUPPLY REMOVE PACKAGING AND PARTS WARNING : • Lay the carton on rear (Please read carefully). face and break open the FOR PERSONAL SAFETY, THIS APPLIANCE MUST bottom flap. BE PROPERLY GROUNDED. Failure to follow these • Set the carton upright instructions can result in death, fire or electrical with all four bottom flaps shock. -
Page 7: Adjust Height Of Ice Maker
Installation Instructions ADJUST HEIGHT AND LEVEL THE WATER SUPPLY SET-UP ICE MAKER • A cold water supply with water pressure Height adjustments may be necessary to install between 30 and the ice maker below a countertop, and may be 120 p.s.i. is required accomplished by adjusting both the front and rear for ice maker leveling legs. -
Page 8: Connect Water Supply To Appliance
Installation Instructions CONNECT WATER SUPPLY TO CONNECT WATER LINE (cont.) APPLIANCE For GE SmartConnect Tubing: ™ • Insert the molded end of the tubing into the ice • The water line should be flushed to clear any foreign maker connection. Tighten the compression nut material before connecting to the ice maker. -
Page 9: Connect The Drain
Installation Instructions CONNECT DRAIN This ice maker is equipped with a gravity drain to prevent water from flowing back into the storage bin and Drain Hose overflowing onto 1” Min. Gap the floor. The ideal installation has a 1-7/8” standpipe with a 2” to 1-1/2”... -
Page 10: Reverse Door Swing
Installation Instructions REVERSE THE DOOR SWING (cont.) REVERSE THE DOOR SWING (Black Door Models Only) STEP 2 - DOOR STOP AND END-CAP REVERSAL IMPORTANT: 1. Remove the hinge pin from the top hinge. Disconnect power to the ice maker. 2. Remove the door from the hinges and replace the Tools Required: top hinge pin. - Page 11 Installation Instructions REVERSE THE DOOR SWING REVERSE THE DOOR SWING (cont.) (cont.) STEP 3 - REVERSE HINGES STEP 4 - REPLACE DOOR 1. Unscrew hinge screws and remove the top hinge. Align handle with the holes in the door and replace Replace screws in empty hinge holes.
-
Page 12: Accessories Zpk2 Auxiliary Pump Kit
Installation Instructions for ZPK2 BEFORE YOU BEGIN: KIT CONTENTS: • Read these instructions completely and carefully. • Auxiliary drain pump IMPORTANT: • • Drain tube, 5/8” ID x 5-1/8” (bin to pump reservoir inlet) Save these instructions for local inspector’s use. IMPORTANT: •... - Page 13 Installation Instructions STEP 1 - REMOVE ORIGINAL PARTS STEP 2 - CONNECT ELECTRICAL 1. Position pump at the right side, just outside of the opening. NOTE: If pump is being installed on a ice maker that has not been completely installed, please proceed to Drain Pump Install section.
- Page 14 Installation Instructions STEP 4 -INSERT DRAIN PUMP STEP 6 - SECURE VENT TUBE 1. Carefully slide the auxiliary drain pump into the 1. Place rear cover against the back of the ice bottom of the ice machine. The tab on the back of machine.
- Page 15 Installation Instructions for ZIP75BB Kit NOTE: If installing a 3/4” trimless custom panel, BEFORE YOU BEGIN: • a 1-1/2” wide filler strip may be required. The filler Read these instructions completely and carefully. strip will act as a spacer between the ice maker IMPORTANT: •...
-
Page 16: Zip75Bb Kit For 3/4" Thick Panels
4. Place the panel with trim against the door to be 2. The Monogram nameplate is held in place with sure that trim and panel fits the door side to side adhesive. Remove the nameplate. and top to bottom. Adjust as needed. - Page 17 Notes...
- Page 18 NOTE: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram local service in your area, call ® 1.800.444.1845. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice.
Need help?
Do you have a question about the ZDIS15 and is the answer not in the manual?
Questions and answers