Control Panel And Features - Whirlpool 7MWTW1700EM1 Use And Care Manual

Control Panel and Features

1
TAMAÑO DE CARGA (Load Size)
1
Select the setting most suitable for your load. CH (Small)
will add a low amount of water for smaller loads and EG
(Extra Large) will add the most amount of water for large
or bulky loads. Items need to move freely. Tightly packing
can lead to poor cleaning performance and may increase
wrinkling and tangling.
TEMPERATURA (Temperature)
2
the washer senses and maintains uniform water
temperatures by regulating incoming hot and cold water.
Select a wash temperature based on the type of fabric
and soils being washed. For best results and following
the garment label instructions, use the warmest wash
water safe for your fabric.
• On some models and cycles, warm and hot water may
be cooler than your previous washer.
• Even in a cold and cool water wash, some warm water
may be added to the washer to maintain a minimum
temperature.
ENJUAGUE ADICIONAL (Extra Rinse)
3
This option can be used to automatically add a second rinse
to most cycles.
WASH CYCLE KNOB
4
Use the Wash Cycle knob to select cycles on your washer.
Knob does not advance during the progress of the cycle, see
cycle status/progress lights for each stage of the process.
See "Cycle Guide" for detailed descriptions of cycles.
INICIO/PAUSA (Start/Pause) Button
5
Press to start the selected cycle; press again to pause the
cycle and unlock the lid. Press and hold for 3 seconds
to cancel a cycle.
NOTE: If the washer is spinning, it may take several
minutes to unlock the lid.
TAPA (Lid Locked)
6
To allow for higher spin speeds, the lid will
lock and the Tapa (Lid Locked) light will turn
on. When this light is lit, the lid is locked
and cannot be opened. When this light is
blinking, the washer is paused. When this
light is off, the lid can be opened.
2
4
6
7 5
If you need to open the lid, press
INICIO/PAUSA (Start/Pause). The lid will
unlock once the washer movement has
stopped. This may take several minutes
if the load was spinning at high speed.
Press INICIO/PAUSA again to resume the cycle.
ETAPAS DE LAVADO (Cycle Status Indicator)
7
The Cycle Status Lights show the progress of a cycle.
At each stage of the process, you may notice sounds or
pauses that are different from traditional washers.
LLENANDO (Sensing Fill)
When the Inicio/Pausa (Start/Pause) button is pressed,
the washer will fill to the selected water level. If the lid is
closed when the washer is done filling, the washer will
begin operation.
If the lid is opened or the Inicio/Pausa button is pressed,
the cycle will pause. Closing the lid and/or pressing the
Start/Pause button will resume the cycle. If the cycle
remains paused with the lid open for 10 minutes, the
washer will pump out the water.
NOTE: The lid will remain unlocked throughout the wash
cycle, then lock before the first spin cycle begins.
LAVADO (Wash)
You will hear the agitator moving the load. The motor
sounds may change at different stages in the cycle.
The wash time is determined by the selected soil level.
ENJUAGUE (Rinse)
You will hear sounds similar to the wash cycle as the
washer rinses and moves the load. You may hear the
motor turning on briefly (short hum) to move the basket
while filling.
Some cycles use spray rinsing. After draining and
spinning out wash water, the washer will continue to spin
and spray in rinse water for the entire rinse time.
DRENADO/EXPRIMIDO (Drain/Spin)
The washer spins the load at increasing speeds for
proper water removal, based on the selected cycle and
spin speed.
LISTO (Done)
Once the cycle is complete, this light will come on.
Remove the load promptly for best results.
3
19