Advertisement
To maintain the sound quality we recommend the
valves be changed every 2-5 years* to maintain the
full sound quality. A new set of valves will give you
back a "NEW" HP 205D amplifier! (* depending upon
use and not withstanding valve failure).
Icon Audio can supply a new set of valves which are
ideal for the HP 205D ranging from standard to
"premium" types. The will be matched and tested for
quality, and audio tested again to check that they are
sonically perfect.
It is essential that only the correct valves are used as
some similar looking valves have a different pin
connection and insertion could result in damage to
the amplifier and risk of electric shock. 5U4/5Z3
rectifier is not suitable.
It is
not
good
practice to
unnecessarily as this can strain the pins and cause micro
air leaks. Icon Audio are happy to check valves and
check the performance of your amplifier, and advise on
the latest upgrades available FOC.
Method:
Switch off, disconnect from mains and allow to stand for
10 mins to allow voltages to discharge. You should
carefully remove the valves, these should be held by the
base when removing to prevent damage. Care should be
taken when removing and inserting the valves. The
rectifier valve has a centre location "spigot" observe
correct orientation. Do not operate without valves!
CAUTION – HEALTH & SAFETY!
When making any adjustments remember to isolate
from power supply, and remember that high voltages
can remain present inside for some time after switch
off.
Service: Should you suspect a problem you could return
the unit to your dealer or Icon Audio for a periodic service
or return the valves for testing free of charge. You should
carefully remove the valves they should be well packed in
cardboard & foam or similar and returned to Icon Audio.
(Valves are very rugged if packed properly).
We welcome any comments you may have regarding
errors or omissions in this manual.
Should you need further advice or information regarding
the use of this unit please contact us.
NEW OWNER?
If you have bought this unit from someone else, please
register with us by email or post stating your name,
address, model, serial number and whom you purchased
from in order that we can keep you up to date with
upgrades and improvements
remove
the valves
Specifications and Features
• All hand wired point to point
• No printed circuit board to 'colour' sound
• Japanese Blue ALPS volume pot.
• High quality Bluetooth receiver (option)
• Class A, all Triode circuit
• Output impedance matching from 16 to 600Ω
• 2 x 205D or 300B output valves
• 2x 6922/E88CC/6DJ8/ECC88 first stage valve
• 1x GZ34/5AR4/274B (not 5U4)
• 2x 1W output per channel max (depending upon load)
• Signal to noise level -90db
• Freq response 20hz-20kHz
• Total harmonic distortion typically less than 0.2% 1khz
• Custom hand wound output transformers
• EI transformers with low oxygen copper
• High quality 2W metal film, & wire-wound resistors
• LED mains indicator
• Polypropylene audio capacitors or Mundorf upgrade option.
• Silver PTFE audio cable
• Gold plated Input terminals
• One line input with "loop out" facility
• 400mV input sensitivity for full output
• 230/117volts 50 watts. Fuse 500mA (2A USA) "T" anti-surge.
• Internal Fuse 100mA "T" type.
• C E, ROHS and WEEE compliant where applicable.
• Dimensions:-
• Amplifier section 22cm W x 32 cm D x 17 H, 7.5 kg (allow
space for connections)
• Power supply – 13cm W x 31cm D x 19cm H, 8.5kg (allow
space for power lead to amp at rear and ventilation for
valves)
• Boxed unit – 45cm D x 40cm W x 32cm H, 20 kgs
(Specifications subject to change, errors & omissions excepted. General 31/05/22)
icon Audio
351 Aylestone Road
Leicester LE2 8TA
www.iconaudio.com
Ph +44 (0) 116 244 0593 +44 (0) 7787 158791
(UK) Ltd
Page 5
Advertisement
