Advertisement
Quick Links
Advertisement
Related Manuals for Digitus DK-1P16-A-050
Summary of Contents for Digitus DK-1P16-A-050
- Page 1 1-Phase AC EV Portable Charger Quick Installation Guide DK-1P16-A-050 – Rev 1.0...
- Page 2 Please read this manual carefully before installation and use, otherwise, it may interfere with the normal use of the equipment and even risk causing personal injury. Safety and Points for Attention 1.1. Installation It shall be installed in the place without violent vibration ...
- Page 3 1.3. Operation Strictly forbidden for Children or persons of restricted capacity to approach the charging device to avoid injury. Forced charging is strictly forbidden when the electric vehicle fails. Electric vehicle can only be charged with the engine is ...
- Page 4 DO not contact metal conductor to prevent electric shock accident. Flame Lightning-proof resistance Overvoltage Waterproof protection IP55 Overcurrent Leakage protection protection Overheat IEC 62196-2 protection connector...
-
Page 5: Package Content
2. Feature Compact size design for good portability • Charging plug meets IEC 62196-2 standard. • • Charging adapter is with IP55 waterproof rating for outdoor usage. EV Charger meets IEC 61851 control principle. • Long durability: Charging adapter at •... - Page 6 AC Input Schuko Input Cable Rated voltage 250V Rated power 3.7kW 8A/10A/13A/16A Rated current (adjustable current) No. of phase 1-Phase Over voltage protection, Under voltage Protection protection, Over current protection, Over temperature protection Residual Electric spec current RCD Type-A protection Terminal temperature ≤50K...
- Page 7 Working -20°C～+50°C temperature Working 5% -95% non condensed Environmental humidity spec Flammability UL94 V-0 standard IP Protection IP55 Insertion life Mechanical spec > 10000 times cycles 5. Led Screen Description Temperatur for the Charging Time Control Box Transpertised Energy Charging Voltage Charging Current Connection and charging status...
- Page 8 5.1. For the Connection and charging status Waiting for connection Charging Charging full 6. How to adjust the max current rating Current adjustment is in the step of 8A,10A, 13A, 16A. Please touch the button “A” on the portable charger to adjust the max. current rating to set an upper limitation with following steps: Power on the device with Schuko AC connected.
- Page 9 The control box can only be touch-switched when it is waiting for connection. During charging process, or when the charging is completed or at the event of failure/error, the touch-switch operation is invalid. Memory function: The max current setting is stored in the memory of the device even after power-off.
-
Page 10: Led Indicator Status Description
7. LED Indicator Status Description Con- POWER CHARGER FAULT Remark dition Bright Initial mode Bright Bright (0.5s) (0.5s) (0.5s) Waiting for charging Normal working mode Flash/1s Charge complete Circuit Board Fault (0.5s Overheat on 0.5s off) protection 1 time Fault (0.5s Undervoltage on 0.5s off) Protection... -
Page 11: Charging Status Indicator
Fault (0.5s Overcurrent on 0.5s off) Protection 5 time Fault (0.5s Leakage on 0.5s off) Protection 7 time Fault (0.5s Communication on 0.5s off) Fail 9 time 8. Charging Status Indicator Please check the power cable is without any damage before powering up. - Page 12 Waiting for charging Charging complete When the charging process is complete: Disconnect the AC power cord. Disconnect the charging cable from the electric vehicle. Cover the charging plug with its protective cover Hereby Assmann Electronic GmbH, declares that the Declaration of Conformity is part of the shipping content. If the Declaration of Conformity is missing, you can request it by post under the below mentioned manufacturer address.
Need help?
Do you have a question about the DK-1P16-A-050 and is the answer not in the manual?
Questions and answers