Table of Contents
Advertisement
Available languages
Available languages
B
VENTILACIÓN SUPERIOR EXTERIOR
VISIÓN GENERAL DE LA
INSTALACIÓN
B1. Adjunte la Placa de Montaje a la
Pared
B2. Prepare el Gabinete Superior
B3. Ajuste el Motor del Calentador
B4. Ventilación Externa
B5. Nstalación Del Adaptador
B6. Montar El Horno
B7. Cómo Ajustar El Adaptador
De Escape
B8. Cómo Conectar
El Conducto
ADHIERA LA PLACA DE
B1
MONTAJE A LA PARED
Adhiera la placa a la pared usando tornillos con
resortes. Por lo menos un tornillo de madera deberá
ser usado para adherir la placa al montaje de pared.
Las ubicaciones recomendadas sobre la placa de
pared están indicadas por A, B, C y D.
1
Retire las tuercas mariposa de los tornillos.
2
Inserte los tornillos en la placa de montaje a
través de los agujeros designados para entrar en
la placa de yeso y vuelva a ajustar las tuercas
mariposa a 3/4" sobre cada tornillo.
16
Instrucciones de Instalación
12"
OPTION 1
NOTE: IT IS VERY IMPORTANT TO
READ AND FOLLOW THE DIRECTIONS
IN THE INSTALLATION INSTRUCTIONS
F. CUT OUT FOR HORIZONTAL
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
4"
OUTSIDE EXHAUST
This Rear Wall Template serves to position the bottom
mounting plate and to locate the horizontal exhaust
outlet.
CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR
1. Use a level to check that the template is positioned
accurately.
2. Locate and mark at least one stud on the left or
right side of the centerline.
NOTE:
It is important to use at least one wood
screw mounted firmly in a stud to support the weight
of the microwave. Mark two additional, evenly spaced
locations for the supplied toggle bolts.
3. Drill holes in the marked locations. Where there is
a stud, drill a 3/16" hole for wood screws. For holes
that do not line up with a stud, drill 5/8" holes for
toggle bolts.
NOTE::
D O NOT INSTALL THE MOUNTING PLATE
AT THIS TIME.
4. Remove the template from the rear wall.
5. Review the Installation Instruction book for your
installation situation.
Darle vuelta a la hoja para consultar la
versión en Español.
CAUTION - IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDED DIMENSION, GREASE-LADEN AIR WILL
DISCHARGE INTO HOUSE STRUCTURE
30" MINIMUM WIDTH REQUIRED
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
REAR WALL TEMPLATE
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
C
Trim the rear wall template along the dotted line.
D
B
IMPORTANTE: NO retire los
espaciadores de cartón entre el
protector de calor y la puerta.
3/8" TO EDGE
OPTION 2
STEP 1:
mark is made by using the stampled slot in bracket.
Installer uses bracket to make 2 marks. First
Second mark is made on the ouside edge of bracket.
Horizontal line
STEP 4:
here,
Make a mark
Make a mark here, along
even with
inside bottom of the
stamped slot provided.
bottom of
stamped
slot
STEP 2:
Installer moves bracket to the other side of
the cabinets and makes 2 more marks. Marks are the
same as STEP 1, just opposite side.
mark here,
Make a
Make a mark here, along
inside bottom of the
even with
stamped slot provided
bottom of
stamped
(same as Step 1).
slot
NOTES:
- 13" Max Cabinet Depth
- 15" deep cabinets require additional steps using
an additional installation kit: JX36BUMP
A
C
PARA USAR TORNILLOS CON RESORTE:
Espacio para Tornillos con Resorte
Superior al Grosor de la Pared
Placa
de
Tuercas Mariposa
Montaje
Tornillo con
Resorte
Pared
Inserte las tuercas mariposa en los agujeros de la
3
pared y coloque la placa de montaje contra la pared.
PRECAUCIÓN
entre la parte trasera de la placa de montaje y la
pared.
Ajuste todos los tornillos. Empuje la placa hacia
4
afuera de la pared para ayudar a ajustar los
tornillos.
(Conducto Vertical)
Extremo del Tornillo
Placa de Montaje
Tenga cuidado para evitar
pellizcos en los dedos
31-7000173 Rev. 0
Advertisement
Table of Contents
