GE JNM3161RFSS Installation Instructions Manual

GE JNM3161RFSS Installation Instructions Manual

Over the range microwave oven
Hide thumbs Also See for JNM3161RFSS:
Table of Contents

Advertisement

Available languages

Available languages

Installation
Instructions
Questions? Call 800.GE.CARES (800.432.2737)

BEFORE YOU BEGIN

Read these instructions completely and carefully.
IMPORTANT –
instructions for local inspector's use.
IMPORTANT –
governing codes and ordinances.
Note to Installer –
instructions with the consumer.
Throughout this manual, features and appearance may
vary from your model.
49-40675-1
(06-13 GE)
Save these
Observe all
Be sure to leave these
AVM4160, JNM3161, and JVM3160
or
Visit our Website at:
Note to Consumer –
for future reference.
– Installation of this appliance requires basic
mechanical and electrical skills.
Proper installation is the responsibility of the installer.
Product failure due to improper installation is not
covered under the warranty.
GEAppliances.com
Keep these instructions
Co ok ing
Co ok ing
Co nv en ien ce
Co nv en ien ce
Pot ato
Pot ato
Bev era ge
Bev era ge
Pop cor n
Pop cor n
Coo k
Coo k
De fro st
De fro st
Tim e
Tim e
Reh eat
Reh eat
Wei ght/ Time
Wei ght/ Time
Tim er
Tim er
On/ Off
On/ Off
Exp res s Co ok
Exp res s Co ok
Add
Add
3
2
3
30 Sec .
2
30 Sec .
1
1
Tur nta ble
6
Tur nta ble
6
5
4
5
4
Sur fac e
Sur fac e
9
9
Lig ht
8
8
Lig ht
7
7
Set
Ven t
Set
Ven t
Pow er
0
Pow er
0
Clo ck
Clo ck
Lev el
Lev el
Sta rt
Sta rt
Ca nc el
Ca nc el
Pau se
Pau se
Off
Off
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.

Advertisement

Chapters

Table of Contents
loading

Summary of Contents for GE JNM3161RFSS

  • Page 1: Before You Begin

    Installation Instructions AVM4160, JNM3161, and JVM3160 Questions? Call 800.GE.CARES (800.432.2737) GEAppliances.com Visit our Website at: BEFORE YOU BEGIN Read these instructions completely and carefully. Note to Consumer – Keep these instructions for future reference. IMPORTANT – Save these – Installation of this appliance requires basic instructions for local inspector’s use.
  • Page 2: Table Of Contents

    Installation Instructions Outside Back Exhaust ........20-23 CONTENTS Installation Overview ........ 20 General information Preparing Rear Wall for Important Safety Instructions........3 Outside Back Exhaust ........20 Electrical Requirements ..........3 Attach Mounting Plate to Wall ..20, 21 Tools You Will Need ............4 Preparation of Top Cabinet.......21 Hood Exhaust ..............
  • Page 3: Important Safety Instructions

    Installation Instructions IMPORTANT SAFETY INSTRUCTIONS A qualified electrician must perform a ground continuity check on the wall receptacle before beginning the encountered, it must be replaced with a properly installation to ensure that the outlet box is properly grounded. If not properly grounded, or if the wall qualified electrician.
  • Page 4: Tools You Will Need

    Installation Instructions TOOLS YOU WILL NEED #1 and #2 Phillips Pencil Carpenter square screwdriver (optional) Ruler or tape measure and straight edge Scissors (to cut template, if necessary) Tin snips (for cutting damper, if required) Filler blocks or scrap wood pieces, if needed Electric drill with 3 16 7 16...
  • Page 5: Hood Exhaust

    Installation Instructions HOOD EXHAUST NOTE: The following chart describes an example of one possible ductwork installation. EQUIVALENT NUMBER EQUIVALENT DUCT PIECES LENGTH x USED LENGTH Roof Cap 24 Ft. 24 Ft. 12 Ft. Straight Duct 12 Ft. 12 Ft. (6 Round) Rectangular-to-Round 5 Ft.
  • Page 6 Installation Instructions NOTE: If you need to install ducts, note that the total duct length of 3 x 10 rectangular or 6 diameter round duct For satisfactory air movement, the total duct length of x 10 rectangular or 6 diameter round duct should Outside ventilation requires a HOOD EXHAUST DUCT.
  • Page 7: Parts Included

    Installation Instructions PARTS INCLUDED INSTALLATION ADDITIONAL PARTS return PART QUANTITY the unit to the store in which it was bought for repair or replacement. repair or Top Cabinet replacement is the responsibility of the customer. Template (if other than the customer), repair or replacement must be made by arrangement between customer ≤...
  • Page 8: Mounting Space

    Installation Instructions MOUNTING SPACE NOTES: The space between the cabinets must be 30 wide and free of obstructions. If the space between the cabinets is greater than 12¾ 30 , a Filler Panel Kit may be used to fill in the gap max.
  • Page 9: Removing The Mounting Plate

    Installation Instructions PLACEMENT OF THE MOUNTING PLATE REMOVING THE MICROWAVE FINDING THE WALL STUDS REMOVING THE MOUNTING PLATE Open the box and fold back all four carton flaps fully against the carton sides. Remove the following items from the protective foam: installation instructions, Wall filters, exhaust adaptor, damper, and the small Studs...
  • Page 10: Determining Mounting Plate Location

    Installation Instructions DETERMINING MOUNTING PLATE LOCATION UNDER YOUR CABINET Plate Position – recessed cabinet bottom Plate Position – flat bottom cabinet Mounting Plate Tabs Touching the Mounting Plate Tabs Back Frame of the Touching the Cabinet Cabinet Bottom 30 to Cooktop Your cabinets may have decorative trim that interferes with the microwave oven installation.
  • Page 11: Aligning The Mounting Plate

    Installation Instructions ALIGNING THE MOUNTING PLATE 30” Hole B Draw a Hole A Vertical Line on Wall from Center of Top Cabinet Hole D Hole C Area E CAUTION: Notch Draw a vertical line on the wall at the center of the 30 NOTE: Holes C and D are inside area E.
  • Page 12: Installation Types

    Installation Instructions INSTALLATION TYPES This microwave oven is designed for adaptation to the following 3 types of ventilation: your installation and proceed to that section. RECIRCULATING OUTSIDE TOP EXHAUST Adaptor in Place for Outside Top Exhaust Cookin g Conven ience Beverag e Potato Popcorn...
  • Page 13: Recirculating

    Installation Instructions RECIRCULATING INSTALLATION OVERVIEW A1. Attach Mounting Plate to Wall A2. Prepare Top Cabinet A3. Install Charcoal Filter (Supplied with AVM4160 and JVM3160 models) A4. Mount the microwave oven A5. Installing/Replacing the Charcoal Filter Without Conven ience Cooking Potato Beverage Popcorn Cook...
  • Page 14: Installing The Charcoal Filter

    Installation Instructions INSTALLING THE CHARCOAL FILTER MOUNT THE MICROWAVE OVEN Remove 2 screws on top of microwave oven, just above the grille panel, using a Phillips screwdriver. If two screws are not accessible, see section A6. Open the door. Remove the grille. Grille CAUTION: Convenience Cooking...
  • Page 15: Mount The Microwave Oven

    Installation Instructions A4 MOUNT THE MICROWAVE OVEN CHARCOAL FILTER WITHOUT ACCESS TO TOP SCREWS AND THE Insert 3 self-aligning screws ( -28 x 2 ”) through UNIT HAS ALREADY BEEN MOUNTED outer top cabinet holes. Turn two full turns on each screw.
  • Page 16: Outside Top Exhaust

    B2. Prepare Top Cabinet B3. Adjust Blower Motor B4. Install Exhaust Adaptor B5. Mount Microwave Oven B6. Adjust Exhaust Adaptor B7. Connect Ductwork Cooki ng Conve nienc e Potato Bevera ge Popco rn Cook Defros t Time Rehea t Weight/T ime Timer On/Off Expre ss Cook 30 Sec.
  • Page 17: Preparation Of Top Cabinet

    Installation Instructions USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET Rotate 90° You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adaptor. Back of Mircrowave Roll the blower so that fan blade openings are...
  • Page 18: Assemble And Install Adaptor

    Installation Instructions MOUNT THE MICROWAVE OVEN ASSEMBLE AND INSTALL ADAPTOR Damper Blower Plate CAUTION: Place the microwave oven in its upright position, with the top of the unit facing up and the front of the unit IMPORTANT: Do not grip or use handle during facing toward you.
  • Page 19: Adjust The Exhaust Adaptor

    Installation Instructions MOUNT THE MICROWAVE OVEN ADJUST THE EXHAUST ADAPTOR Open the top cabinet and adjust the exhaust adaptor Insert a self-aligning screw through top-center to connect to the house duct. cabinet hole. Temporarily secure the microwave oven by turning the screw at least two full Damper turns after the threads have engaged.
  • Page 20: Outside Back Exhaust

    C1. Prepare Rear Wall C2. Attach Mounting Plate to Wall C3. Prepare Top Cabinet C4. Adjust Blower C5. Mount the Microwave Oven Cooki ng Conve nienc e Potato Bevera ge Popco rn Defros t Cook Rehea t Time Weight/T ime Timer...
  • Page 21: Outside Back Exhaust

    Installation Instructions ATTACH THE MOUNTING PLATE ADAPTING BLOWER FOR TO THE WALL cont OUTSIDE BACK EXHAUST 1 Remove the blower motor screws that holds the blower plate to the microwave oven. Slide the plate toward the Spacing for Toggles More back of the microwave and lift up to remove.
  • Page 22: Mount The Microwave Oven

    Installation Instructions ADAPTING BLOWER FOR MOUNT THE MICROWAVE OVEN OUTSIDE BACK EXHAUST cont. Gently place the fan back into the cavity with the exhaust portion of the fan at the top and facing the back of the unit. CAUTION: IMPORTANT: Do not grip or use handle during Note: Make sure the wires remain routed through installation.
  • Page 23 Installation Instructions MOUNT THE MICROWAVE OVEN Insert a self-aligning screw through top-center cabinet hole. Temporarily secure the microwave oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Insert 2 self-aligning screws ( -28 x ) through outer top cabinet...
  • Page 24: Before You Use Your Microwave Oven

    Installation Instructions BEFORE YOU USE YOUR MICROWAVE OVEN Make sure the microwave oven has been Read the Owner’s Manual. installed according to instructions. Remove all packing material from the KEEP INSTALLATION INSTRUCTIONS microwave oven. FOR THE LOCAL INSPECTOR’S USE. Install turntable and turntable ring in cavity. Replace house fuse or turn breaker back on.
  • Page 25 Horno microondas para Instrucciones colocar encima de la estufa de Instalación AVM4160, JNM3161, y JVM3160 ¿Preguntas? Llame a 800.GE.CARES (800.432.2737) o visite nuestro sitio web en: GEAppliances.com ANTES DE COMENZAR Nota para el Comprador – Conserve estas Lea estas instrucciones en su totalidad y instrucciones para referencia futura.
  • Page 26 Instrucciones de Instalación Escape de Salida Trasero ......20-23 CONTENIDOS Visión General de la Instalación ....20 Información General Preparación de la Pared Trasera Instrucciones Importantes de Seguridad ....3 para el Escape de Salida Trasero ....20 Requisitos Eléctricos ............3 Adjunte la Placa de Montaje a la Pared ..20 Herramientas Que Necesitará...
  • Page 27: Instrucciones Importantes De Seguridad

    Instrucciones de Instalación INSTRUCCIONES IMPORTANTES DE SEGURIDAD Un electricista calificado deberá realizar un control de Cuando se encuentre un tomacorriente de pared de dos la continuidad de la conexión a tierra en el receptáculo de la pared antes de comenzar con la instalación, a fin de asegurar que la caja del tomacorriente esté...
  • Page 28 Instrucciones de Instalación HERRAMIENTAS NECESARIAS Destornillador Lápiz Escuadra de Phillips nº1 y nº2 carpintero (opcional) Regla o cinta métrica y extremo recto Tijeras (para cortar plantillas, si es necesario) Tijeras para hojalata (para cortes en reguladores, si se requiere) Bloques de llenado o piezas de fragmentos de madera, si son necesarios para para generar Taladro eléctrico con brocas...
  • Page 29: Campana De Escape

    Instrucciones de Instalación CAMPANA DE ESCAPE ESCAPE DE SALIDA SUPERIOR (SÓLO EJEMPLO) En el siguiente cuadro se describe un ejemplo de una posible instalación de conductos. LONGITUD NÚMERO EQUIVALENT PIEZAS DEL CONDUCTO EQUIVALENTE x USADO =EQUIVALENTE Tapa del Techo 24 pies 24 pies Conducto Recto 12 pies...
  • Page 30 Instrucciones de Instalación NOTA: Si necesita instalar tuberías, deberá observar que la longitud total de una tubería rectangular de 3 1/4” x 10” o Para un movimiento satisfactorio del aire, la longitud total una circular de 6” de diámetro de la tubería rectangular de 3 ¼” x 10” o circular 6” de diámetro La ventilación externa requiere un CONDUCTO DE SALIDA DE Los codos, transiciones, pared y tapas para...
  • Page 31: Partes Incluidas

    Instrucciones de Instalación PARTES INCLUIDAS INSTALACIÓN PIEZAS ADICIONALES devuelva PARTE CANTIDAD la unidad a la tienda donde fue comprada para su reparación o reemplazo. Plantilla del Si la unidad es dañada por el cliente, la reparación Gabinete o reemplazo es responsabilidad del cliente. Superior (si no es el cliente), la reparación o reemplazo deberá...
  • Page 32: Espacio De Montaje

    Instrucciones de Instalación ESPACIO DE MONTAJE NOTAS: El espacio entre los gabinetes debe ser de 30” de ancho y estar libre de obstrucciones. Si el espacio entre los gabinetes es superior a 30”, Máx. de se podrá usar un Kit de Panel de Relleno para 12¾...
  • Page 33: Colocación De La Placa De Montaje

    Instrucciones de Instalación COLOCACIÓN DEL PLATO DE MONTAJE RETIRO DEL HORNO MICROONDAS BÚSQUEDA DEL MONTAJE DE PARED DE MONTAJE Abra la caja y vuelva a doblar las cuatro lengüetas de la caja completamente contra los costados de la caja. Retire los siguientes artículos de la gomaespuma Montaje de protectora: instrucciones de instalación, filtros, Pared...
  • Page 34 Instrucciones de Instalación DETERMINACIÓN DE LA PLACA DE MONTAJE DEBAJO DE SU GABINETE Las Lengüetas de Las lengüetas la Placa de Montaje de la Placa de Tocan la Estructura Montaje Tocan la Inferior del Gabinete Parte Inferior del Gabinete 30” a la Placa de Cocción saliente Es posible que sus gabinetes posean bordes decorativos...
  • Page 35 Instrucciones de Instalación ALINEE LA PLACA DE MONTAJE 30” Hole B Dibuje una Línea Agujero A Vertical en la Pared desde el Centro a la Parte Superior del Gabinete Hole D Agujero C Área E PRECAUCIÓN Ranura dedos en extremos puntiagudos. Dibuje una línea vertical en la pared en el centro del NOTA: Los agujeros C y D están dentro del área E.
  • Page 36: Tipos De Instalación

    Instrucciones de Instalación TIPOS DE INSTALACIÓN (Elija A, B o C) Este horno microondas está diseñado para ser adaptado a los siguientes 3 tipos de ventilación: A. Recirculación (Sin Conductos no Ventilados) B. Escape Exterior Superior (Conducto Vertical) RECIRCULACIÓN (SIN ESCAPE EXTERIOR SUPERIOR CONDUCTOS NO VENTILADOS) (CONDUCTO VERTICAL)
  • Page 37: Arecirculación

    Instrucciones de Instalación RECIRCULACIÓN (Sin Conductos No Ventilados) VISIÓN GENERAL DE LA INSTALACIÓN A1. ADHERA LA PLACA DE MONTAJE A LA PARED A2. USE LA PLANTILLA DEL GABINETE SUPERIOR PARA LA PREPARACIÓN DEL GABINETE SUPERIOR A3. CÓMO INSTALAR EL FILTRO DE CARBÓN (Suministrado de modelos de AVM4160 y JVM3160) A4.
  • Page 38: Cómo Instalar El Filtro De Carbón

    Instrucciones de Instalación CÓMO INSTALAR EL FILTRO DE CARBÓN MONTE EL HORNO MICROONDAS Retire los 2 tornillos en la parte superior del horno microondas, justo arriba del panel de la rejilla, usando un destornillador Phillips. Si los dos tornillos no están accesibles, lea la sección Abra la puerta.
  • Page 39 Instrucciones de Instalación A4 MONTE EL HORNO (cont.) FILTRO DE CARBÓN SIN ACCESO A Inserte 3 tornillos autoalineantes (1/4” – 28 x 2 ¼”) a LOS TORNILLOS SUPERIORES Y LA través de los agujeros del gabinete superior externo. UNIDAD YA FUE MONTADA Dé...
  • Page 40: Adjunte La Placa De Montaje A La Pared

    B3. Ajuste el Motor del Calentador B4. Instale el Adaptador del Escape B5. Monte el Horno Microondas B6. Ajuste el Adaptador del Escape B7. Conecte la Tubería Cookin g Conve nience Bevera ge Potato Popcor n Defros t Cook Time Reheat...
  • Page 41: Preparación Del Gabinete Superior

    Instrucciones de Instalación AJUSTE EL MOTOR DEL USE LA PLANTILLA DEL GABINETE CALENTADOR (cont.) SUPERIOR PARA LA PREPARACIÓN DEL GABINETE SUPERIOR Gire 90° Es necesario que haga agujeros para los tornillos de soporte de la parte superior, un agujero lo suficientemente grande para que el cable de corriente pueda pasar, y un disyuntor lo suficientemente grande Parte trasera...
  • Page 42: Ensamble E Instale El Adaptador

    Instrucciones de Instalación MONTE EL HORNO MICROONDAS ENSAMBLE E INSTALE EL ADAPTADOR Regulador Plato Calentador PRECAUCIÓN: riesgo de lesión personal (lesión en la espalda u contar con la ayuda de dos personas para instalar Coloque el horno microondas en su posición vertical, con la parte superior de la unidad hacia arriba y el IMPORTANTE: No tome ni use la manija durante la frente hacia usted.
  • Page 43: Ajuste El Adaptador Del Escape

    Instrucciones de Instalación MONTE EL HORNO MICROONDAS AJUSTE EL ADAPTADOR DEL ESCAPE (cont.) Abra el gabinete superior y ajuste el adaptador del Inserte un tornillo autoalineante a través del escape para realizar la conexión al conducto del hogar. agujero de la parte superior del centro del gabinete. En forma temporaria asegure el horno dando al Regulador tornillo por lo menos dos giros completos una...
  • Page 44: Visión General De La Instalación

    C2. Adjunte la Placa de Montaje a la Pared C3. Prepare el Gabinete Superior C4. Ajuste el Calentador C5. Monte el Horno Microondas Cooki ng Conve nienc e Potato Bevera ge Popco rn Defros t Cook Rehea t Time Weight/T ime Timer...
  • Page 45: Preparación Del Gabinete Superior

    Instrucciones de Instalación ADHIERA LA PLACA DE MONTAJE ADAPTACIÓN DEL CALEFACTOR A LA PARED (cont.) PARA EL ESCAPE EXTERIOR TRASERO Para usar tornillos con resorte: 1 Retire el tornillo del motor del calentador que Espacio para Tornillos con Resorte sostiene el plato calentador sobre el horno Superior al Grosor de la Pared microondas.
  • Page 46 Instrucciones de Instalación ADAPTACIÓN DEL CALEFACTOR PARA MONTE EL HORNO MICROONDAS EL ESCAPE TRASERO EXTERIOR (cont.) De forma suave vuelva a colocar el ventilador en la cavidad con la parte del escape del ventilador arriba y enfrentando la parte trasera de la unidad. PRECAUCIÓN: riesgo de lesión personal (lesión en la espalda u contar con la ayuda de dos personas para instalar...
  • Page 47 Instrucciones de Instalación MONTE EL HORNO MICROONDAS (cont.) Inserte un tornillo autoalineante a través del agujero de la parte superior del centro del gabinete. En forma temporaria asegure el horno dando al tornillo por lo menos dos giros completos una vez que las roscas fueron colocadas.
  • Page 48: Antes De Usar Su Horno Microondas

    Instrucciones de Instalación ANTES DE USAR EL HORNO MICROONDAS Asegúrese de que el horno microondas haya Lea el Manual del Propietario. sido instalado de acuerdo con las instrucciones. Retire todos los materiales de embalaje del horno MANTENGA LAS INSTRUCCIONES DE microondas.

This manual is also suitable for:

Jvm3160rfssAvm4160dfbsAvm4160dfws

Table of Contents