2. Install the Battery 1. Open the back cover. 2. Insert the battery. 3. Put the cover back.
Page 4
3. Insert the nano-SIM Card 1. Insert the tip of the tray eject tool into the hole. 2. Pull out the card tray and place the nano-SIM card on the tray, as shown. Carefully slide the tray back into place.
Page 5
4. Start Your Device Press and hold the power button until the screen lights up and then the device will connect to the Internet automatically. NOTE: If the battery is extremely low, you may be unable to power on the device. Please charge your device first.
5. Access the Internet Wi-Fi: Touch the icon on the screen to get the default Wi-Fi SSID and password. Connect to the Wi-Fi network with your mobile deviceand then access the Internet. USB Type-C cable: Connect with the computer via USB port and then access the Internet.
6. Change Your Device Settings You can change the device settings by logging in to the configuration web page. Touch >Advanced Setting to get thedefault device manager website URLandpassword. Launch the Internet browser. Enter the URL in the Address bar. Click Login.
Page 8
7. E-label You can touch the Support icon on the screen to get the E-lable information.
Page 10
Press and hold for about 2 seconds to power Power button on your device. nano-SIM card Insert your nano-SIM card. tray Touch screen Description icons Signal strength Network type Wi-Fi signal strength Internet connection status New software available. Battery power level Set whether data usage is displayed on the screen and the max data amount.
Page 11
View or change your device settings. Use the WPS function. Show your device information. Describe the icons displayed on the screen. Charging/USB Charge the device or connect to the USB port Type-C jack of a computer.
Troubleshooting Problem Recommended Action If the driver of your device is abnormal, connection reinstall the software. You need to between your uninstall the software first. device and a PC through a cable cannot established automatically. Ensure that the Wi-Fi function is connection enabled.
Page 13
Troubleshooting Problem Recommended Action client Ensure that your nano-SIM card is connected to available. device Change the location and find a place cannot access with good signal. the Internet. Check the settings of the WAN connection mode. ...
Images and screenshots used in this guide may differ from the actual product. Content in this guide may differ from the actual product or software. Trademarks ZTE and the ZTE logos are trademarks of ZTE Corporation. Other trademarks and trade names are those of their respective owners. Version No.: R1.0...
Warning and Notice To the User • If inadequately shielded, some electronic devices, for example, the electronic system of vehicles, may be affected by the electromagnetic interference caused by the device. Consult the manufacturers of such devices before using the device if necessary.
If the battery shows signs of swelling or leakage, please stop use immediately. Battery Safety • Using ZTE-unapproved or incompatible battery, charger or power adapter may damage your device, shorten its lifespan or cause a fire, explosion or other hazards.
Page 18
• If the battery damages or shows signs of swelling or leakage, please stop use immediately and contact ZTE or ZTE authorized service provider for replacement. • Return the worn-out battery to the provider or put it in the designated recycle place.
ZTE under the above-mentioned situations. This warranty is end users’ sole remedy and ZTE’s sole liability for defective or nonconforming items, and is in lieu of all other warranties, expressed, implied or statutory, including but not...
Page 20
• This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. •...
FCC RF Exposure Information (SAR) • This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the United States. • • During SAR testing, this device is set to transmit at its highest certified power level in all tested frequency bands, and placed in positions that simulate RF exposure in usage against the head with no separation, and near the body with the...
10 mm between this and your body. Limitation of Liability ZTE shall not be liable for any loss of profits or indirect, special, incidental or consequential damages resulting from or arising out of or in connection with using of this product, no matter...