Advertisement
2. Without a Security Code (If You Have Forgotten or Lost the Security Code)
Remove JP1 (as shown to the right). For the K-1900W-2 and K-1900D-2,
Step 1.
the plastic cover must be removed to expose the circuit board.
Connect the K-1900 Series device to a C.O. line, analog PABX/KSU station
Step 2.
or to a DLE-200B Line Simulator.
Step 3.
From a Touch Tone phone, call into the K-1900 Series phone).
Listen for at least one ringback in the calling phone and then take the K-
Step 4.
1900 Series phone off-hook (answer the phone).
A double beep indicates the K-1900 Series phone is in the programming
Step 5.
mode (see sections B-G ).
Step 6.
When programming is finished, replace JP1 and replace cover on phone.
B. Quick Programming Features
Speed dial number (see section C) 1-32 digits or pauses .................................................................. Phone Number
Security Code, factory set to 845464 (see section E) ......................................................................... 6 digits
To add a Q anywhere in the dialing string............................................................................................ QQ
To add a # anywhere in the dialing string............................................................................................. Q#
To set dialing speed to normal - 120ms tones/10 pps (factory setting) ............................................... Q1
To set dialing speed to fast - 50ms tones/20pps ................................................................................. Q2
To restrict Touch Tone user dialing (factory setting) ............................................................................ Q3
To enable Touch Tone user dialing....................................................................................................... Q4
Toggles between pulse and Touch Tone dialing (see section C).......................................................... Q6
To add a 4 second pause anywhere in the dialing string (see section C)............................................. Q7
To add a 1 second pause anywhere in the dialing ............................................................................... Q8
To clear all programming and change back to factory settings............................................................. ###
C. Programming Examples
To Program the K-1900 Series Phone to .....
...to Touch Tone dial 555-1234
...to pulse dial 555-1234 followed by a Touch Tone 9
...to dial a 9, a 4 second pause and then 555-1234
...to set the dialing speed to fast
...to enable unlimited user dialing after the phone has speed dialed
...to clear the speed dial number or disable speed dialing
D. Touch Tone and Pulse Dial Speeds
The K-1900 Series phone can be programmed to dial at normal or fast dialing speeds. While in the programming mode, enter Q1
for normal dialing speed - 120ms on/off Touch Tones or 10 pps pulse dialing. Enter Q2 for fast dialing speed - 50ms on/off Touch
Tones or 20 pps pulse dialing.
E. Security Code
A six digit security code is required to access the programming mode. The factory set security code is 845464 (V-I-K-I-N-G). It is
recommended that you change the security code to a personal 6 digit (0-9) number in memory position #9 while in the programming
mode. Note: The security code must be six digits in length and cannot contain a Q or #.
F. Touch Tone or Pulse Dialing
The K-1900 Series phones are factory set to automatically dial using Touch Tones. A Q6 entered in the speed dial number will toggle
the dialing mode between Touch Tone and pulse (see section C).
Note: You can NOT program a Q or # to be pulse dialed.
G. Touch Tone User Dialing Restriction (factory enabled)
The K-1900 Series phones is factory set to restrict fraudulent calls from hand held pocket dialers. After speed dialing, the K-1900
Series phones will restrict (hang up) when they detect any Touch Tone that they did not generate. To restrict user dialing, enter Q3
while in the programming mode. To enable user dialing, enter Q4 while in the programming mode.
An optional Q170600 internal ringer is available.
For more information, see DOD# 834.
Adding an Internal Ringer
3
Step 1 - See Section A
Enter Programming
Enter Programming
Enter Programming
Enter Programming
Enter Programming
Enter Programming
.47 mF @ 250V
(included with ringer)
T
R
Note: JP1 MUST be in place
for normal operation.
Enter Digits
+
Location
+
+
Step 2- Enter Digits
5551234 + #0
Q6 5551234 Q6 9 + #0
9 Q7 5551234 + #0
Q2
Q4
#0
Q170600
Electronic Ringer
JP1
#0
#9
Advertisement
