Service Prevention Checklist - Electrolux EFLS210TIW00 Use & Care Manual

Service Prevention Checklist

Before calling for service, review this list. It may save both time and expense. The list includes common occurrences that are not
the result of defective workmanship or materials in this washer.
OCCURRENCE POSSIBLE CAUSE
NOISE
High pitch "jet engine" A certain amount of motor whine is normal
noise. during the spin cycle.
Rattling and clanking Foreign objects such as coins or safety pins
noise. may be in drum or pump.
Belt buckles and metal fasteners are hitting
wash drum.
Thumping sound. Heavy wash loads may produce a thumping
sound. This is usually normal. If sound con-
tinues, washer is probably out of balance.
Vibrating noise. Washer is not resting firmly on floor.
Shipping bolts and foam block have not
been removed during installation.
Wash load unevenly distributed in drum.
OPERATING
Washer does not start. Electrical power cord may not be plugged in
or connection may be loose.
House fuse blown, circuit breaker tripped, or
a power outage has occurred.
Water supply faucets are not turned on.
Motor is overheated. Washer motor will stop
if it becomes overheated.
Washer door is not completely closed.
Washer won't spin. Load is too small.
Residue left in drum. Heavily soiled items.
SHOWN IN LED DISPLAY
"Check the tap" Water inlet hoses are not installed.
Water supply valves are not turned on.
No or slow water fill
Water supply is not adequate in installation.
Water is being used elsewhere in the house.
Water inlet hoses are kinked.
Water inlet screens are clogged.
"Check drain filter" Drain pipe blocked.
Washer experiencing drain
Pump filter clogged.
problems during cycle
"Check the door"
Washer door is open or
not closed completely
"Water safety alert" Drain pipe position too low and water
siphoning out drain hose.
Washer not maintaining
water level
If drain pipe height is adequate, error
detected can only be resolved by calling
service technician.
"Detergent overdosing" An excessive amount of detergent has been
added, causing extra suds; additional rins-
Too many suds detected ing has not corrected the issue.
Solutions to Common Problems
SOLUTION
Stop washer and check drum. If noise continues after washer is restarted,
objects may be in pump. Call your authorized servicer.
To prevent unnecessary noise and damage to drum, fasten fasteners and
turn items inside out.
Stop washer and redistribute wash load.
Move washer so it rests firmly on floor. Adjust leveling legs. See INSTALLA-
TION INSTRUCTIONS for details.
See INSTALLATION INSTRUCTIONS for removing shipping bolts and foam
block.
Stop washer and rearrange wash load.
Make sure plug fits tightly in wall outlet.
Reset circuit breaker or replace fuse. Do not increase fuse capacity. If prob-
lem is a circuit overload, have it corrected by a qualified electrician. If problem
is a power outage, call local electric company.
Turn on water supply faucets.
It will automatically restart after a cool down period of up to 30 minutes (if
washer has not been manually turned off).
Close door completely.
Add 1 or 2 similar items to help balance the load.
Wipe drum with a nonabrasive household cleanser, then rinse. Shake or
brush excess dirt and sand from items before washing
Install Hot and Cold water hoses and turn on Hot and Cold water supply valves.
Turn on Hot and Cold water supply valves.
Test water pressure at another faucet in the house. Water pressure must be
at least 30 psi (260 kPa).
Avoid running water elsewhere while washer is filling.
Straighten hoses.
Remove hoses and clean sediment from screens.
Unclog drain pipe.
See Care and Cleaning for pump filter cleaning instructions.
Close door completely.
Drain pipe height must be minimum 24" above bottom of unit. Refer to
Installation Instructions for correct drain pipe installation requirements and
adjust accordingly
Close all water supply faucets and call your authorized servicer.
Use less detergent. Verify detergent is fit for use in front load washers. Look
for this symbol on the detergent label:
25
.