Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Greenlee ES750
Summary of Contents for Greenlee ES750
- Page 1 Battery-powered Cable Cutter 45380—with 120 V Charger 45381—with 220 V Charger 99926288 ES750 Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. © 2007 Greenlee Textron Inc. IM 1322 REV 7 2/07...
-
Page 2: Table Of Contents
Parts List ... 15–16 Description The Greenlee Battery-powered Cable Cutter is intended to cut up to 750 Kcmil copper and aluminum cable. The cable cutter is driven by a 12-volt motor and is powered by a rechargeable NiCd (nickel cadmium) battery. The motor is protected by a circuit breaker. -
Page 3: Important Safety Information
Hazards or unsafe practices which, if not avoided, MAY result in injury or property damage. Read and understand all of the instructions and safety informa- tion in this manual before operating or servicing this tool. Failure to observe this warning could result in severe injury or death. ES750... - Page 4 • Do not cut steel or ACSR. • Inspect the tool before each use. Replace any worn, damaged, or missing items with Greenlee replacement parts. A damaged or improperly assembled tool can break and strike nearby personnel. Failure to observe these precautions may result in injury or property damage.
- Page 5 • Do not store the battery at more than 140 °F (60 °C). Damage to the battery can result. • Do not use another manufacturer’s charger. Other manufacturers’ chargers may overcharge and damage the battery. Failure to observe these precautions may result in injury or property damage. ES750...
- Page 6 IMPORTANT SAFETY INFORMATION Battery (cont’d) • Do not expose the battery to liquids such as water, oil, or solvents. Liquids will damage the battery. • Do not attempt to open the battery. It contains no user-serviceable parts. • Use this battery for manufacturer’s intended use only. Use other than that which is described in this manual can result in injury or property damage.
- Page 7 Failure to observe these warnings could result in severe injury or death. Greenlee recommends plugging the charger directly into a receptacle. If an extension cord must be used: • Select an extension cord with a configuration that exactly matches that of the charger’s plug.
- Page 8 IMPORTANT SAFETY INFORMATION Charger (cont’d) Use this charger to charge the supplied 12-volt rechargeable NiCd (nickel cadmium) batteries only. Other batteries may burst if charged with this charger. Failure to observe this warning could result in severe injury or death. Do not place anything other than the supplied 12-volt rechargeable NiCd (nickel cadmium) battery into the battery pocket.
-
Page 9: Specifications
Depth ... 4-1/8" Wire Type ... Copper or aluminum Maximum Wire Size ... 750 Kcmil Motor ... 12 VDC Battery Type ... Rechargeable nickel-cadmium Voltage ... 12 V Charger Voltage ... 120 VAC or 220 VAC Trigger ES750 RESET (yellow button) -
Page 10: Operation
Operation 1. Slide the direction control lever to select either FORWARD or REVERSE. Press the switch to activate the cable cutter. Release the switch after the movable blade is disengaged from the driver. 2. Place the cable to be cut against the stationary blade until it is engaged by the driver. Close the movable blade around the cable. -
Page 11: Charger
After approximately one hour, the LED will turn off to indicate that the battery is fully charged. 4. Remove the battery from the charger. Note: Allow the charger to cool for at least 15 minutes before charging another battery. ES750... -
Page 12: Troubleshooting
Troubleshooting Problem Cutter does not operate. Charging LED does not illuminate. Battery life has decreased. Probable Cause Battery is discharged. The internal circuit breaker has tripped. Movable blade is not completely engaged. Control lever in LOCK position. The battery contacts are dirty. The battery cartridge is too warm. -
Page 13: Maintenance
(1A) on top. Make sure circuit breaker button is in its proper location. Also make sure the internal wires are not pinched. Turn unit over and tighten screws (42). Do not overtighten screws. Make sure hanging ring is reattached. 12. Install brush (13) with screws (38). Use pin to align holes before reassembling screws. ES750... -
Page 14: Illustration
Illustration 24 x 4 20 x 7 39 x 2 40 x 5 13 16 x 7 40 x 5 39 x 3 42 x 6... -
Page 15: Parts List
Gear plate ... 1 Gear ... 4 Washer ... 1 Gear case ... 1 Ring Gear Kit (includes items 27–31) Bearing ... 1 Gear ... 1 Pin ... 2 Gear washer ... 1 Gear ... 1 Gear plate ... 2 ES750... - Page 16 Contact ... 1 Decal, WEEE recycle symbol ... 1 12 V battery 120 V charger 220 V charger Plastic case 800-435-0786 815-397-7070 800-435-0786 Greenlee Textron Inc. is a subsidiary of Textron Inc. • Fax: 800-451-2632 Fax: 815-397-1865 Fax: 800-524-2853 Fax: +1-815-397-9247...