Related Manuals for Fujitsu FTP-62HWSL001 Series
Summary of Contents for Fujitsu FTP-62HWSL001 Series
- Page 1 FUJITSU Component Thermal Printer Mobile Printer FTP-62HWSL001 Series User's Guide FUJITSU COMPONENT LIMITED...
- Page 2 Thank you for purchasing the FTP-62HWSL001 Series Mobile Printer (hereafter referred to as “this product”). This User's Guide (hereafter referred to as “this guide”) contains precautions to use it safely and correctly. Before using this product, please read the complete this guide.
- Page 3 If you wish to use this product in an environment that requires high safety, please consult with our sales representatives. ■ Copyright This product and this guide are copyrighted works of FUJITSU COMPONENT LIMITED. This product and this manual must not be reproduced, duplicated, used, or modified, partially or in full, without permission.
- Page 4 ■ Export This device may contain commodities, technology or software subject to export laws and regulations from the US and other countries. Diversion contrary to the country law is prohibited. ■ Warranty We shall not be responsible for any failure caused by wrong operation or usage in the wrong environment.
- Page 5 ■ For USA This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 6 ■For CANADA This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
- Page 7 ■ Explanation of Symbols The following symbols are used in this guide. Please read and understand the meaning of each symbol in this guide. If this product should malfunction, immediately stop using it, and contact your sales representative. Indicates an imminent risk of causing severe personal Danger injury or death if not used properly.
- Page 8 ■ General Cautions Warning - Do not use in the environment with corrosive gas or salt wind is present. Break- down Failure to observe this may cause failure. - Do not modify or disassemble. Failure to observe this may cause fire, explosion or Modify breakdown.
- Page 9 Caution - Do not use while driving a vehicle or walking. Failure to observe this may cause traffic accidents and injuries. Injury - Do not use the printer near the equipment that generates large radiation noise, such as a high voltage device and a large motor. Break- down Failure to observe this may cause malfunction or breakdown.
- Page 10 ■ Printer Warning - Do not use the printer in a location where radio wave generation is prohibited. Accident Might cause accidentally a malfunction of the instrument. - During or immediately after operation, do not touch the print head, the support plate and the motor. Heat is not immediately Burn discharged.
- Page 11 ■ Battery Warning - Do not use the battery for other device or purpose. Failure to observe this may cause destruction. Break- down - Do not disassemble the battery. Failure to observe this may cause heat, fire or destruction. Modify - Only use the specified battery.
- Page 12 ■ AC Adapter Warning - Do not use the AC adapter for any other devices or purposes. Failure to observe this may cause damage to the printer and/or Break- down battery. - Only connect the AC adapter to the specified voltage and/or frequency.
- Page 13 ■ Warning Label of Product This product comes with the following warning label. This label must not be peeled off or erased from the display. Moreover, please contact the distributor when the label is difficult to see due to dirt, scratching etc. Warning display Content ヘッド...
-
Page 14: Table Of Contents
1 Preparation to Print ................. 14 Packaging ..................14 Getting to Know the Printer ............15 Inserting the Battery ..............19 Connecting AC Adapter (Charging) ..........20 Inserting the Paper ..............21 2 Operating Procedures ................22 Power On ..................22 Test Print .................. -
Page 15: Preparation To Print
1 Preparation to Print 1.1 Packaging The following items are included. There may be attachment of optional parts depending on a product type. If anything is missing, please contact the distributor. Printer AC adapter Battery AC Cable... -
Page 16: Getting To Know The Printer
1 Preparation to Print 1.2 Getting to Know the Printer ■ Front Side (Cover Closed) : Cover to open and load paper. Paper Cover : To cut paper. Paper Cutter : Operates and Displays status of the printer. Operation Panel : To open the cover. - Page 17 1 Preparation to Print ■ Operation Panel : To turn the power supply ON or OFF. Power Switch : To Feed paper. Feed switch : Displays printer status. Status LED : Displays Communication status. Communication LED...
- Page 18 1 Preparation to Print ■ Front Side (Cover Open) : To feed paper. Platen Roller : This shows warning when using printer. Warning Label : This sensor detects the status of paper. Paper Sensor ■ Back view (Cover Open) : This applies heat to paper. Thermal Head...
- Page 19 1 Preparation to Print ■ Side : Displays printer type and Product Label other product information. Charge Terminal : Charge with the Cradle (Optional)
-
Page 20: Inserting The Battery
1 Preparation to Print 1.3 Inserting the Battery Caution Life of the battery is about 500 charges. (At the normal temperature) If an old battery is used, not only the equipment malfunctions and this might cause destruction. 1. Please slide cover lock and lift the Cover open ③... -
Page 21: Connecting Ac Adapter (Charging)
1 Preparation to Print 1.4 Connecting AC Adapter (Charging) The battery is charged by the printer's built-in charger. Caution Please stop charging immediately if an abnormal charge is generated. 1. Please connect the AC cable with the AC adapter, and connect the AC plug to an outlet. -
Page 22: Inserting The Paper
1 Preparation to Print 1.5 Inserting the Paper 1. Please push up the cover open lever to open the paper cover. Cover open lever 2. Please insert the paper in the printer. Thermal Paper (Thermosensitive Side) 2. Please put out the edge of the paper and close the paper cover. -
Page 23: Operating Procedures
2 Operating Procedures 2.1 Power On 1. Please push the POWER Switch until the LED light turns green. 2. It is possible to turn the power off by pushing the POWER Switch until the LED turns off. -
Page 24: Test Print
2 Operating Procedures 2.2 Test Print This product has a test print function. The setting of the printer can be confirmed by this test print. 1. Please turn the power off and push the Feed switch. 2. Please turn the power on while holding with the Feed switch down.Then, the test print starts. - Page 25 2 Operating Procedures Check pattern The thermal head open circuit etc. can be confirmed. Version The firmware and CG version can be confirmed. Interface Available interface can be confirmed. Bluetooth information The Bluetooth Addres can be confirmed. Setting information etc The setting information etc can be confirmed.
-
Page 26: Bluetooth Communication
2 Operating Procedures 2.3 Bluetooth Communication Explanation of how to communicate and print with a Bluetooth device from a terminal such as a personal computer: 1. Please turn the printer on. 2. Please find the Bluetooth device in the host terminal. 3. -
Page 27: Printer Error
2 Operating Procedures 2.4 Printer Error The error occurs when the printer cannot print/work normally. The type of error is shown by the LED when the error is occurring. Please reset the status when the error occurs. The following example explains reasons and solutions for problems. Error Cause Solution... - Page 28 2 Operating Procedures Error Cause Solution Supply Voltage - The battery charge is low. - Please charge Error the battery. Mark Undetection - The mark of paper is not - Please use the paper on correctly printed. which mark - Particles have correctly printed.
-
Page 29: Indicator Lights
3 Indicator Lights The LED displays printer error status. Important It may be difficult to see the LED display in a bright place such as in direct sunshine etc. 3.1 Normal Operation Lighting Pattern Printer Status Status LED Communication LED Power ON G (about 5sec) Power OFF... -
Page 30: Printer Error
3 Indicator Lights 3.3 Printer Error Lighting Pattern Printer Status Status LED Communication LED Low Battery O (Lighting) Supply Voltage Error R (Lighting) MCU Operation Error R (Blinking) / RAM Error Hardware Error R (Blinking) Bluetooth Error R (Blinking) Paper Cover Open R (Blinking) Paper End R (Blinking) -
Page 31: Maintenance
4 Maintenance Please service this printer regularly. Caution Do not service the printer while the battery is inserted or the AC adapter connected. Do not completely service, disassemble and repair any parts that are not explained in this chapter. 4.1 Thermal Head Please service the thermal head once a month. -
Page 32: Platen Roller
4 Maintenance 4.2 Platen Roller Please service the platen roller once a month. 1. Please open the paper cover. (Refer to chapter 1.5) 2. Soak a cotton ball with some alcohol and wipe the platen roller gently until it is clean. Please use isopropyl alcohol. 3. -
Page 33: Troubleshooting
5 Troubleshooting ■ Power Problem Cause Solution Printer does not Is a battery inserted? or Is it Please insert the battery turn on inserted reversed? correctly. (C. 1.3) Is the battery fully charged? Please charge the battery. (C. 1.4) Is the POWER Switch Please push the POWER correctly pushed? Switch correctly. - Page 34 5 Troubleshooting ■ Communication Problem Cause Solution Printer does not Is the power turned off? Please turn on the communicate power. (C. 2.1) Is the application or the Please use the driver for this product application or the driver used? for this product.
- Page 35 5 Troubleshooting ■ Print Problem Cause Solution Printer does not Is the power turned off? Please turn on the feed the paper power. (C. 2.1) Is the paper correctly Please insert the paper Paper jam inserted? correctly. (C. 1.5) occurs Is the paper cover Please close the paper closed?
- Page 36 5 Troubleshooting ■ Others Problem Cause Solution Print starting Does the mark detection Please remove the location is operate correctly? reason for the mark incorrect (C. 3.2) detection error. (C. 2.4) Printing is slow Is the battery charge low? Please charge the battery.
-
Page 37: Specifications
6 Specifications 6.1 Printer Specifications Items Contents Print Method Thermal Line-dot Printing Resolution 8dot/mm (203dpi) Dimensions 103.5×86×44mm Weight About 300g (Including battery, excluding paper) Max Print Width About 48mm Print Speed Max 120mm/sec Battery full charge, Print ratio 12.5% Character Alphanumeric, Katakana : 8x16, 16x16, 12x24, 24x24 International and Special... -
Page 38: Paper Specifications
6 Specifications 6.2 Paper Specifications Items Contents Type Thermal Roll Paper Width Outer Up to φ40mm Diameter Inner φ 12mm or more Diameter Thickness 60 to 115μm Specified Type Name Manufacture Standard Paper HW54S Nippon Paper Group Medium Term PD150R Oji Imaging Media Storage Long Term... -
Page 39: Recycle
7 Recycle This symbol means: Do not dispose of this product together with your household waste! Please refer to your local community or contact our dealers to properly handle the end-of-life of electric and electronic equipment. Recycling this product will help to conserve natural resources and prevent potential negative impact on the environment and human health caused by inappropriate handling. -
Page 40: Appendix
8 Appendix 8.1 Bluetooth Communication (1) Android Terminal 1. Please turn on the power of printer. 2. Please open "Settings" - " WIRELESS ＆ NETWORKS" from the menu of terminal, and turn on Bluetooth. 3. Please open the "Bluetooth”, and tap "FTP-62HWSL…". (Please tap "SEARCH FOR DEVICES", if it does not appear) 4. - Page 41 8 Appendix (2) iOS Terminal 1. Please turn on the power of printer. 2. Please open "Settings" - "Bluetooth" from the menu of terminal, and turn on Bluetooth. 3. Please tap "FTP-62HWS…" from "Devices". 4. When the connection with the printer succeeds, "Connected" is displayed to "FTP-62HWS…".
-
Page 42: Product Support
Moreover, when you request repair, please provide the model name and the product serial number in addition to information on the actual failure etc. Technical Support Section FUJITSU COMPONENT LIMITED (Japan) Global Marketing Dept.2 Tel: +81-3-3450-1645 Fax: +81-3-3474-2385 E-mail: fcl-contact@cs.jp.fujitsu.com... - Page 44 Mobile Printer FTP-62HWSL001 Series User's Guide L0NA02301-L011RS Published by FUJITSU COMPONENT LIMITED Jan. 2016 Rev. 1...