Advertisement
Quick Links
HERITAGE/MODE MODELS:
100M, 100W, 200M & 200W
INSTALLATION AND OPERATING INSTRUCTIONS
STOVES MUST BE FITTED BY APPROVED, QUALIFIED AND
PLEASE LEAVE THIS BOOKLET WITH THE HOUSEHOLDER
Penman Stoves operate at very high temperatures. All persons
including children and the infirm should be warned of this and not
allowed to touch any surfaces whilst in use. The operator must use
17JUL14_HERMOD_V3
APPROVED ‐ CONFORMING TO EN13240:2001 and
EN13240 A2:2004
COMPETENT INSTALLERS
the glove provided.
www.penmancollection.com
Advertisement
Related Manuals for Penman Collection 100M
Summary of Contents for Penman Collection 100M
- Page 1 HERITAGE/MODE MODELS: 100M, 100W, 200M & 200W APPROVED ‐ CONFORMING TO EN13240:2001 and EN13240 A2:2004 INSTALLATION AND OPERATING INSTRUCTIONS ...
- Page 2 The following is a list of stove accessories your retailer will be able to supply: • Penman matching graphite high temperature paint • Stove Glass Cleaner • Spare Rope • Rope Seal Adhesive • CO Detector • Penman Stove Fan • Penman Stove Thermometer • Wood Moisture Meter • Spare Gloves • Permanent Ventilators • Purpose‐built Ash Vacuum Cleaner • Penman Ash Carrier • Penman Fire Screens • Penman Companion Sets • Penman Log Baskets • Penman Soot Box HETAS LTD APPROVAL ...
- Page 3 Contents PAGE YOUR STOVE CONTROLS, ITS OUTPUT AND EFFICIENCY 1 LIFETIME GUARANTEE 2 INSTALLATION, OPERATION AND MAINTENANCE 3 SAFETY NOTES AND TROUBLESHOOTING 21 COMPONENT DRAWING AND SPARES LIST 24 Your Stove Controls, Output and Efficiency Heritage 100M with Lattice shown Secondary Air Control Primary Air Control Riddling Mechanism ANTHRACITE WOOD FUEL EFFICIENCY EFFICIENCY WITHOUT WOOD WITHOUT WOOD STOVE CLEAN BURN CLEAN BURN CLEAN BURN KIT CLEAN BURN KIT HERITAGE/MODE ...
- Page 4 LIFETIME GUARANTEE All Penman Stoves are covered by a lifetime guarantee (valid for original purchases only) from date of sale. This guarantee excludes the following naturally wearing consumable items: Door Glass, Firebricks, Rope Seals, Baffle & Grate (including riddling system). In addition, the following criteria must be met. • Sight ...
- Page 5 Installation, Operation and Maintenance IMPORTANT: THIS APPLIANCE MUST BE INSTALLED BY A COMPETENT PERSON AND THE INSTALLATION MUST COMPLY WITH BS8303 – CODE OF PRACTICE FOR INSTALLATION OF DOMESTIC HEATING AND COOKING APPLIANCES BURNING SOLID MINERAL FUEL, NATIONAL BUILDING REGULATIONS, LOCAL BY‐LAWS AND STANDARDS AND THE REQUIREMENTS OF THE HEALTH AND SAFETY AT WORK ACT ‐ IN PARTICULAR: ...
- Page 6 Installation Once the installation is complete, the installer must advise the householder on the correct use of the stove and warn them to use only the recommended fuels listed in this document. The installer must also advise the householder on the actions to be taken should smoke or fumes be emitted from the stove. Your Penman stove must not share a chimney with any other appliance Where the chimney is believed to have previously served an open fire installation it is possible that the higher flue gas temperature from a closed appliance may loosen deposits that were previously firmly adhered, with the consequent risk of flue blockage. It is therefore recommended that the chimney ...
- Page 7 The chimney must be swept before connection to the stove and swept every twelve months thereafter. It is recommended that your chimney is swept every six months. An existing fireplace opening can be modified to accommodate the stove. The following pages identify some typical installation scenarios and provides the necessary specific installation information for your new stove. Always consult your stove supplier for a detailed survey of your particular circumstances. To make it easier to handle the stove on installation, remove the baffle plates, bricks ...
- Page 8 Typical Installation for Inglenook Fireplaces – rear flue – Side View Heritage 200M shown 17JUL14_HERMOD_V3 ...
- Page 9 Ideally, the old fireplace should be filled in so that there is a smooth streamlined entry into the flue. The length of the horizontal run of the flue pipe must not exceed the flue outlet diameter on the stove. It is essential that all connections between the stove and chimney flue are sealed and made airtight. Both chimney and flue pipe must be accessible for cleaning and if ALL parts of the chimney cannot be reached through the stove, a soot door must be fitted to enable this to be done. SOOT DOOR Heritage 100M shown 17JUL14_HERMOD_V3 ...
- Page 10 Typical Installation Into In‐filled Masonry Fireplaces Heritage 200M shown 17JUL14_HERMOD_V3 ...
- Page 11 Carefully lay the stove on its back and using the screws provided fit the legs in place. Carefully set the stove upright and replace the internal components. The following information applies to all variants of the Heritage/Mode 100M, Heritage/Mode 100w, Heritage/Mode 200M, Heritage/Mode 200w stoves. Clearances ...
- Page 12 should be taken to level the stove and secure the hearth. If existing floors do not have adequate load bearing capacity then suitable modifications must be adopted. All other standard thickness hearths are suitable too. When the stove is in the desired position, fix the brackets provided to the back feet and level the stove using the levelling screws, then mark the hearth through the holes, remove the stove, and drill and plug the hearth for securing the stove. Ventilation Into a Room For Combustion Air is an Essential Requirement. Any apertures provided for this purpose must not be restricted or blocked Flues Without a Flue Draft Stabiliser When installing the Heritage/Mode 100 stoves without a flue draft stabiliser into houses built before 2008, no additional permanent ventilation will be required. ...
- Page 13 Lattice Installation Remove the glass panel as shown on page 20 and locate the lattice in place from the back of the door. Ensure that the steel tabs are located against the window frame and the heat resistant pads are in place over the steel tabs to protect the glass panel. Replace the glass panel as described on page 20. Top or Rear Flue Remove the collar and accessory pack from the stove. The stove will arrive with the blanking plate fitted to the rear. This can be removed if required allowing the collar to be fitted for rear flue installations. The circular cut out in the rear heat shield must be removed to enable this style of connection – see image below. Remove the panel from the stove by unscrewing the four screws and then remove the circular cut out for rear flue installations. Replace the rear heat shield. Remember to fit the blanking plate to the unused flue position if it has been removed. ...
- Page 14 Dimensions DIM 100M 100W 200M 200W HERITAGEE MODEE HERITAGEE MODEE HERITAGEE MODEE HERITAGEE MODEE [mm] A 573 568 573 568 630 630 630 630 B 474 451 474 451 578 551 578 551 C 225 213 225 213 275 ...
- Page 15 Operation ALWAYS OPEN THE STOVE DOOR SLOWLY AND ALWAYS USE THE GLOVE Primary Air Primary air is controlled via the rotating vent in the bottom of the door. This provides an air draught to the bed of the fire. Rotate anti‐clockwise to open and clockwise to close. Open this when you start a fire and to manage anthracite fires. It should be closed when a wood fire is established for the best efficiency. Secondary Air ...
- Page 16 Once established and for the best results from your Heritage/Mode 100W or 100M stove, load about 1.5 to 2 kg of good quality dry wood per hour with the primary air control fully closed and the secondary air control about half to two thirds closed. Logs can be up to 300mm or 12” long. Do not overload. Once established and for the best results from your Heritage/Mode 200W or 200M stove, load about 2 to 3 kg of good quality dry wood per hour with the ...
- Page 17 With some solid fuels a residue of burnt fuel or clinker will accumulate on the grate, allow the fire to go out periodically to remove this. Once established and for the best results from your Heritage/Mode 100M stove, load about 1 kg of anthracite or equivalent per hour with the primary air control about half to three quarters open and the secondary air control fully ...
- Page 18 Recommended Fuels Please note that HETAS Ltd Appliance Approval only covers the use of wood logs and approved smokeless fuels on this appliance. HETAS Ltd Approval does not cover the use of other fuels either alone or mixed with the recommended fuels listed above, nor does it cover instructions for the use of other fuels Wood ‐ Only kiln‐dried or well‐seasoned wood with a moisture content reading of less than 18% is recommended. A Penman moisture meter is a handy device to have and is available from your supplier. As a rule‐of‐thumb, wood seasons at about 1” (25mm) per year, so a log split such that along its length no dimension is greater than 3” (75mm), it would take about 3 years to dry. A dry log will produce ...
- Page 19 Further information on the requirements of the Clean Air Act can be found at: http://smokecontrol.defra.gov.uk/ Your stove, as listed, below has been recommended as suitable for use in smoke control areas when burning dry wood and the “authorised” fuels listed below. It is supplied with a small kit in a blister pack which must be fitted if you intend to burn dry wood in a smoke control area. Please note the table below and follow the instructions if you intend to operate your stove in smoke control zone. DRY SMOKE FREE FIT KIT IF WOOD STOVE WOOD SOLID FUEL IS TO BE BURNT Heritage/Mode 100M FIT KIT Heritage/Mode 100W N/A NOT REQUIRED Heritage/Mode 200M FIT KIT Heritage/Mode 200W N/A ...
- Page 20 Clean Burn Kit Installation Instructions FOR INSTALLER ONLY 1. Open the stove door. 2. Slide the secondary air control completely to the right. 3. Remove the small screw under the top of the stove positioned to the left of the secondary air control 4. Fit the screw from the blister pack and ensure it is screwed in tightly. This kit will prevent the secondary air from fully closing, whilst still providing good control. It reduces the maximum efficiency of the anthracite burn by a few percentage points – see the chart at the beginning of these instructions. Some additional key points relating to burning fuel on this appliance when used in the Clean Burn mode follow: Refuelling Onto a Low Fire Bed If the fire bed is not sufficient to light a new fuel charge, excessive smoke emission can occur. Refuelling must be carried out onto a bed of glowing embers ...
- Page 21 The throat plate locates on the back firebricks/tertiary air plenum and side firebricks so note its position before removal. To remove, lift plate and bring forwards, dropping the left side as you bring it forwards. Tilt it at an angle to withdraw it, left side first from the front of the stove. It may help to remove the ...
- Page 22 Inner Grate Removal and Replacement Lift the inner grate vertically until it clears the locating pin of the riddling mechanism housed in the ash pan chamber, then manoeuvre the grate out of the stove. When replacing, ensure the slot engages with the pin. Outer Grate Removal and Replacement Remove all the bricks and the inner grate. Lift the outer grate up at an angle left higher than right and manoeuvre the grate out left side first. There is always a knack to such a task, but it is easy once learnt! Stove Body The stove is finished with a heat‐resistant paint and this can be cleaned with a soft brush. Do not clean whilst the stove is hot, wait until it has cooled down. The finish can be renovated with Penman stove paint available from your supplier. Glass Panels Clean the glass panels when cool with Penman glass cleaner. Highly abrasive substances ...
- Page 23 Seasonal Maintenance If your stove is be unused for any length of time, e.g. summer months, then it is recommended that it is cleaned out thoroughly. Air slides should be lightly oiled with WD40 or similar and left partially open to allow air circulation. Regular monitoring of the inside components will identify condensation or water ingress. If these problems occur, then your stove needs to be dried and the cause of the problem rectified. After a shut down, and before reuse, the appliance should be cleaned again and the chimney swept, it is essential to have the chimney swept at least once annually and it is recommended that it is swept twice a year. Safety Notes and Troubleshooting IT IS ESSENTIAL AND REQUIRED BY BUILDING REGULATIONS THAT A CO ALARM IS INSTALLED IN THE SAME ROOM AS THIS APPLIANCE Fires Can Be Dangerous Always use a fire guard to BS 8423:2002, Fireguards for Use With Solid Fuel Appliances, ...
- Page 24 Smoke and Fumes Entering the Room When properly installed and operated, this appliance will not emit fumes into the room. Occasional fumes from de‐ashing and refuelling may occur and is normal. Persistent fume emission with closed doors must not be tolerated. If fume emission does persist, then the following immediate action should be taken – ...
- Page 25 Poor Heat Output Stove too small for room Seek advice from a qualified heating engineer as to (kW) output required for room size. As a guideline the volume of the room in cubic feet divided by 500 i.e. room 15’ x 15’ x 8’ would require 3.6kW approx. Chimney and / or flue pipe restricted, room ventilation restricted. On Installation these will have been checked but regular maintenance is necessary as conditions can change i.e. soot build up, birds nesting, masonry fall, dust build up or furniture blocking vents. Poor quality fuel. Only burn dry seasoned timber, soft woods have a lower heat output than hard woods. Use a Moisture Meter. Solid fuels vary in heat value, check with your coal merchant as to suitability. Dirty Glass ...
- Page 26 Component Parts Refer to the key on the following page. Many spare parts are stocked – please refer to your retailer or supplier if you require any replacement parts. Please only use components made specifically for your stove. Parts List 17JUL14_HERMOD_V3 ...
- Page 27 KEY DESCRIPTION 1 PRIMARY AIR CONTROL KNOB 2 HANDLE 3 DOOR CASTING 4 HANDLE BRACKET 5 REMOVABLE LATTICE 6 WINDOW ROPE 7 GLASS WINDOW 8 WINDOW RETAINING FRAME 9 WINDOW RETAINING CLIP AND SCREW 10 FRONT CASTING 11 HANDLE CATCH BRACKET 12 BAR/LOG RETAINER 13 INNER GRATE 14 OUTER GRATE 15 ASH PAN 16 LEFT AND RIGHT BOTTOM BRICKS 17 BOTTOM CASTING 18 RIDDLING MECHANISM 19 RIDDLING ACTUATOR ...
- Page 28 Product Fiches 17JUL14_HERMOD_V3 ...
- Page 29 17JUL14_HERMOD_V3 ...
- Page 30 Brought to you by Percy Doughty & Co Imperial Point, Express Trading Estate, Stone Hill Road, Farnworth, Bolton. BL4 9TN 01204 868 550 17JUL14_HERMOD_V3 ...